+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
-
/*
* B4860 QDS board configuration file
*/
-#define CONFIG_B4860QDS
-#define CONFIG_PHYS_64BIT
-
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#else
-#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-#define CONFIG_SYS_TEXT_BASE 0x00201000
#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
#define CONFIG_SPL_PAD_TO 0x40000
#define CONFIG_SPL_MAX_SIZE 0x28000
#define RESET_VECTOR_OFFSET 0x27FFC
#define BOOT_PAGE_OFFSET 0x27000
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#define CONFIG_SYS_NO_FLASH
#endif
#endif
#endif
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_NO_FLASH
#endif
/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_MP /* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC /* Enable IFC Support */
-#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
-#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
+#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#ifndef CONFIG_PPC_B4420
+#ifndef CONFIG_ARCH_B4420
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
#define CONFIG_SRIO2 /* SRIO port 2 */
#define CONFIG_SRIO_PCIE_BOOT_MASTER
#endif
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR 0x77
#define CONFIG_ENV_OVERWRITE
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
+#ifndef CONFIG_MTD_NOR_FLASH
#else
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_ENV_SECT_SIZE 0x10000
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (512 * 1097)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR 0xffe20000
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_ENV_IS_NOWHERE)
#define CONFIG_ENV_SIZE 0x2000
#else
-#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_FSL_DDR3
#ifndef CONFIG_SPL_BUILD
#define CONFIG_FSL_DDR_INTERACTIVE
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_RAMBOOT
#endif
-#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
* open - index 2
* shorted - index 1
*/
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-#endif
-
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
/* I2C */
#define CONFIG_SYS_I2C
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS 25
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#ifdef CONFIG_PHYS_64BIT
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
#ifdef CONFIG_FMAN_ENET
#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/
#define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6 /*SLOT 2*/
-
#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c
#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d
#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e
#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC1"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
#define CONFIG_SYS_FSL_B4860QDS_XFI_ERR
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * Command line configuration.
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
-
-/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
#endif
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
#define __USB_PHY_TYPE ulpi
-#ifdef CONFIG_PPC_B4860
+#ifdef CONFIG_ARCH_B4860
#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \
"bank_intlv=cs0_cs1;" \
"en_cpc:cpc2;"
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=b4860qds/ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
+ "fdtaddr=1e00000\0" \
"fdtfile=b4860qds/b4860qds.dtb\0" \
"bdev=sda3\0"
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
+ "setenv fdtaddr 0x01e00000;" \
"setenv loadaddr 0x1000000;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#include <asm/fsl_secure_boot.h>
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff