#define CONFIG_ARM7 1 /* This is a ARM7 CPU */
#define CONFIG_B2 1 /* on an B2 Board */
#define CONFIG_ARM_THUMB 1 /* this is an ARM7TDMI */
-#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */
+#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */
+#define CONFIG_SYS_NO_CP15_CACHE
+#define CONFIG_ARCH_CPU_INIT
#define CONFIG_S3C44B0_CLOCK_SPEED 75 /* we have a 75Mhz S3C44B0*/
/*
* Size of malloc() pool
*/
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_ENV_SIZE 1024 /* 1024 bytes may be used for env vars*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024 )
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_ENV_SIZE 1024 /* 1024 bytes may be used for env vars*/
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024 )
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_LAN91C96
+#define CONFIG_LAN91C96
#define CONFIG_LAN91C96_BASE 0x04000300 /* base address */
#define CONFIG_SMC_USE_32_BIT
#undef CONFIG_SHOW_ACTIVITY
/*
* select serial console configuration
*/
+#define CONFIG_S3C44B0_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
+#define CONFIG_S3C44B0_I2C
+#define CONFIG_RTC_S3C44B0
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
-
+#define CONFIG_NET_MULTI
#define CONFIG_BOOTDELAY 5
#define CONFIG_ETHADDR 00:50:c2:1e:af:fb
#define CONFIG_BOOTARGS "setenv bootargs root=/dev/ram ip=192.168.0.70:::::eth0:off \
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0C400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x0C400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C800000 /* 4 ... 8 MB in DRAM */
-#define CFG_LOAD_ADDR 0x0c700000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x0c700000 /* default load address */
-#define CFG_HZ 1000 /* 1 kHz */
+#define CONFIG_SYS_HZ 1000 /* 1 kHz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00400000 /* 4 MB */
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CFG_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CFG_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
-#define CFG_FLASH_READ0 0x0000 /* 0 is standard */
-#define CFG_FLASH_READ1 0x0001 /* 1 is standard */
-#define CFG_FLASH_READ2 0x0002 /* 2 is standard */
+#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x0 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x0 /* environment starts at the beginning of the EEPROM */
/*-----------------------------------------------------------------------
* I2C EEPROM (STM24C02W6) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0xFE
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0xFE
-#define CFG_I2C_EEPROM_ADDR 0xA8 /* EEPROM STM24C02W6 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0xA8 /* EEPROM STM24C02W6 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
-/*#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/* Flash banks JFFS2 should use */
/*
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_FIRST_SECTOR 2
-#define CFG_JFFS2_NUM_BANKS 1
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 2
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
*/
/*
- Linux TAGs (see lib_arm/armlinux.c)
+ Linux TAGs (see arch/arm/lib/armlinux.c)
*/
#define CONFIG_CMDLINE_TAG
#undef CONFIG_SETUP_MEMORY_TAGS