#define CONFIG_TSEC_ENET 1 /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for DDR setup*/
-#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
-
#define CONFIG_SYS_CLK_FREQ 33000000
/*
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_CMD_SDRAM 1 /* SDRAM DIMM SPD info printout */
+#define CONFIG_CMD_SDRAM 1 /* SDRAM DIMM SPD info printout */
#define CONFIG_ENABLE_36BIT_PHYS 1
#undef CFG_DRAM_TEST
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define PCI_SPEED 33333000 /* CPLD currenlty does not have PCI setup info */
#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#else
- /*
- * Manually set up DDR parameters
- */
- #define CFG_SDRAM_SIZE 1024 /* DDR is 1024MB */
- #define CFG_DDR_CS0_BNDS 0x0000000f /* 0-1024 */
- #define CFG_DDR_CS0_CONFIG 0x80000102
- #define CFG_DDR_TIMING_0 0x00260802
- #define CFG_DDR_TIMING_1 0x38355322
- #define CFG_DDR_TIMING_2 0x039048c7
- #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
- #define CFG_DDR_MODE 0x00000432
- #define CFG_DDR_INTERVAL 0x05150100
- #define DDR_SDRAM_CFG 0x43000000
-#endif
+#define CFG_DDR_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
+
+/* Manually set up DDR parameters */
+#define CFG_SDRAM_SIZE 1024 /* DDR is 1024MB */
+#define CFG_DDR_CS0_BNDS 0x0000000f /* 0-1024 */
+#define CFG_DDR_CS0_CONFIG 0x80000102
+#define CFG_DDR_TIMING_0 0x00260802
+#define CFG_DDR_TIMING_1 0x38355322
+#define CFG_DDR_TIMING_2 0x039048c7
+#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE 0x00000432
+#define CFG_DDR_INTERVAL 0x05150100
+#define DDR_SDRAM_CFG 0x43000000
#undef CONFIG_CLOCKS_IN_MHZ
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER 1
+#define CONFIG_FLASH_CFI_DRIVER 1
#define CFG_FLASH_CFI 1
#define CFG_FLASH_EMPTY_INFO
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#if defined(CONFIG_PCI)
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
-#define CFG_ENV_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */