powerpc/p4080ds: Move ICS refclk define into P4080DS.h

[platform/kernel/u-boot.git] / include / configs / ATUM8548.h

diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h
index 49a86fd..78757ec 100644 (file)
--- a/include/configs/ATUM8548.h
+++ b/include/configs/ATUM8548.h
@@ -47,6 +47,10 @@
 #define CONFIG_MPC85xx         1       /* MPC8540/60/55/41/48 */
 #define CONFIG_MPC8548         1       /* MPC8548 specific */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xfff80000
+#endif
+
 #define CONFIG_PCI             1       /* enable any pci type devices */
 #define CONFIG_PCI1            1       /* PCI controller 1 */
 #define CONFIG_PCIE1           1       /* PCIE controler 1 (slot 1) */
@@ -91,9 +95,6 @@
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
 #define PCI_SPEED              33333000        /* CPLD currenlty does not have PCI setup info */
-#define CONFIG_SYS_PCI1_ADDR   (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCI2_ADDR   (CONFIG_SYS_CCSRBAR+0x9000)
-#define CONFIG_SYS_PCIE1_ADDR  (CONFIG_SYS_CCSRBAR+0xa000)
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -176,7 +177,7 @@
 #define CONFIG_SYS_FLASH_WRITE_TOUT    8000    /* Flash Write Timeout (ms) */
 
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER    1
 #define CONFIG_SYS_FLASH_CFI           1
@@ -190,12 +191,11 @@
 /* Memory */
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xe4010000      /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END        0x4000          /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       0x4000          /* Size of used area in RAM */
 
 #define CONFIG_SYS_INIT_L2_ADDR        0xf8f80000      /* relocate boot L2SRAM */
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128             /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (256 * 1024) /* Reserve 256 kB for Mon */
@@ -203,7 +203,6 @@
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -382,14 +381,6 @@
  */
 #define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */