Merge git://git.denx.de/u-boot-mpc85xx

[platform/kernel/u-boot.git] / include / commproc.h

diff --git a/include/commproc.h b/include/commproc.h
index 6e0a233..9d4cb10 100644 (file)
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -51,20 +51,6 @@
 /*
  * DPRAM defines and allocation functions
  */
-
-/* The dual ported RAM is multi-functional.  Some areas can be (and are
- * being) used for microcode.  There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#ifdef  CONFIG_SYS_ALLOC_DPRAM
-
-#define CPM_DATAONLY_BASE      ((uint)0x0800)
-#define CPM_DATAONLY_SIZE      ((uint)0x0700)
-#define CPM_DP_NOSPACE         ((uint)0x7fffffff)
-
-#else
-
 #define CPM_SERIAL_BASE                0x0800
 #define CPM_I2C_BASE           0x0820
 #define CPM_SPI_BASE           0x0840
@@ -74,8 +60,6 @@
 #define CPM_POST_BASE          0x0980
 #define CPM_WLKBD_BASE         0x0a00
 
-#endif
-
 #ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
 #define CPM_POST_WORD_ADDR     0x07FC
 #else
@@ -456,62 +440,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT        ((uint)0x00002c00)
 #endif /* CONFIG_BSEIP */
 
-/***  ESTEEM 192E  **************************************************/
-#ifdef CONFIG_ESTEEM192E
-/* ESTEEM192E
- * This ENET stuff is for the MPC850 with ethernet on SCC2. This
- * is very similar to the RPX-Lite configuration.
- * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
- */
-
-#define        PROFF_ENET      PROFF_SCC2
-#define        CPM_CR_ENET     CPM_CR_CH_SCC2
-#define        SCC_ENET        1
-
-#define PA_ENET_RXD    ((ushort)0x0004)
-#define PA_ENET_TXD    ((ushort)0x0008)
-#define PA_ENET_TCLK   ((ushort)0x0200)
-#define PA_ENET_RCLK   ((ushort)0x0800)
-#define PB_ENET_TENA   ((uint)0x00002000)
-#define PC_ENET_CLSN   ((ushort)0x0040)
-#define PC_ENET_RENA   ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT        ((uint)0x00003d00)
-
-#define PB_ENET_LOOPBACK ((uint)0x00004000)
-#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
-
-#endif
-
-/***  IP860  **********************************************************/
-
-#if defined(CONFIG_IP860)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define        PROFF_ENET      PROFF_SCC1
-#define        CPM_CR_ENET     CPM_CR_CH_SCC1
-#define        SCC_ENET        0
-#define PA_ENET_RXD    ((ushort)0x0001)        /* PA 15 */
-#define PA_ENET_TXD    ((ushort)0x0002)        /* PA 14 */
-#define PA_ENET_RCLK   ((ushort)0x0200)        /* PA  6 */
-#define PA_ENET_TCLK   ((ushort)0x0100)        /* PA  7 */
-
-#define PC_ENET_TENA   ((ushort)0x0001)        /* PC 15 */
-#define PC_ENET_CLSN   ((ushort)0x0010)        /* PC 11 */
-#define PC_ENET_RENA   ((ushort)0x0020)        /* PC 10 */
-
-#define PB_ENET_RESET  (uint)0x00000008        /* PB 28 */
-#define PB_ENET_JABD   (uint)0x00000004        /* PB 29 */
-
-/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT        ((uint)0x0000002C)
-#endif /* CONFIG_IP860 */
-
 /***  KM8XX  *********************************************************/
 
 /* The KM8XX Service Module uses SCC3 for Ethernet */