Prepare v2023.10

[platform/kernel/u-boot.git] / drivers / video / ssd2828.c

diff --git a/drivers/video/ssd2828.c b/drivers/video/ssd2828.c
index be68d38..4cdcbe7 100644 (file)
--- a/drivers/video/ssd2828.c
+++ b/drivers/video/ssd2828.c
@@ -1,7 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+
 /*
  * (C) 2015 Siarhei Siamashka <siarhei.siamashka@gmail.com>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -11,9 +10,11 @@
  */
 
 #include <common.h>
+#include <malloc.h>
 #include <mipi_display.h>
 #include <asm/arch/gpio.h>
 #include <asm/gpio.h>
+#include <linux/delay.h>
 
 #include "videomodes.h"
 #include "ssd2828.h"
@@ -340,7 +341,7 @@ static int ssd2828_configure_video_interface(const struct ssd2828_config *cfg,
 int ssd2828_init(const struct ssd2828_config *cfg,
                 const struct ctfb_res_modes *mode)
 {
-       u32 lp_div, pll_freq_kbps, pll_config;
+       u32 lp_div, pll_freq_kbps, reference_freq_khz, pll_config;
        /* The LP clock speed is limited by 10MHz */
        const u32 mipi_dsi_low_power_clk_khz = 10000;
        /*
@@ -374,6 +375,20 @@ int ssd2828_init(const struct ssd2828_config *cfg,
        }
 
        /*
+        * Pick the reference clock for PLL. If we know the exact 'tx_clk'
+        * clock speed, then everything is good. If not, then we can fallback
+        * to 'pclk' (pixel clock from the parallel LCD interface). In the
+        * case of using this fallback, it is necessary to have parallel LCD
+        * already initialized and running at this point.
+        */
+       reference_freq_khz = cfg->ssd2828_tx_clk_khz;
+       if (reference_freq_khz  == 0) {
+               reference_freq_khz = mode->pixclock_khz;
+               /* Use 'pclk' as the reference clock for PLL */
+               cfgr_reg |= SSD2828_CFGR_CSS;
+       }
+
+       /*
         * Setup the parallel LCD timings in the appropriate registers.
         */
        if (ssd2828_configure_video_interface(cfg, mode) != 0) {
@@ -390,10 +405,10 @@ int ssd2828_init(const struct ssd2828_config *cfg,
        /* PLL Configuration Register */
        pll_config = construct_pll_config(
                                cfg->mipi_dsi_bitrate_per_data_lane_mbps * 1000,
-                               cfg->ssd2828_tx_clk_khz);
+                               reference_freq_khz);
        write_hw_register(cfg, SSD2828_PLCR, pll_config);
 
-       pll_freq_kbps = decode_pll_config(pll_config, cfg->ssd2828_tx_clk_khz);
+       pll_freq_kbps = decode_pll_config(pll_config, reference_freq_khz);
        lp_div = DIV_ROUND_UP(pll_freq_kbps, mipi_dsi_low_power_clk_khz * 8);
 
        /* VC Control Register */