#include <linux/dma-mapping.h>
#include <linux/scatterlist.h>
#include <linux/slab.h>
+#include <linux/gpio.h>
#ifdef CONFIG_SUPERH
#include <asm/sh_bios.h>
struct clk *fclk;
char *irqstr[SCIx_NR_IRQS];
+ char *gpiostr[SCIx_NR_FNS];
struct dma_chan *chan_tx;
struct dma_chan *chan_rx;
},
/*
+ * Common SH-2(A) SCIF definitions for ports with FIFO data
+ * count registers.
+ */
+ [SCIx_SH2_SCIF_FIFODATA_REGTYPE] = {
+ [SCSMR] = { 0x00, 16 },
+ [SCBRR] = { 0x04, 8 },
+ [SCSCR] = { 0x08, 16 },
+ [SCxTDR] = { 0x0c, 8 },
+ [SCxSR] = { 0x10, 16 },
+ [SCxRDR] = { 0x14, 8 },
+ [SCFCR] = { 0x18, 16 },
+ [SCFDR] = { 0x1c, 16 },
+ [SCTFDR] = sci_reg_invalid,
+ [SCRFDR] = sci_reg_invalid,
+ [SCSPTR] = { 0x20, 16 },
+ [SCLSR] = { 0x24, 16 },
+ },
+
+ /*
* Common SH-3 SCIF definitions.
*/
[SCIx_SH3_SCIF_REGTYPE] = {
if (!reg->size)
return;
- if (!(cflag & CRTSCTS))
- sci_out(port, SCSPTR, 0x0080); /* Set RTS = 1 */
+ if ((s->cfg->capabilities & SCIx_HAVE_RTSCTS) &&
+ ((!(cflag & CRTSCTS)))) {
+ unsigned short status;
+
+ status = sci_in(port, SCSPTR);
+ status &= ~SCSPTR_CTSIO;
+ status |= SCSPTR_RTSIO;
+ sci_out(port, SCSPTR, status); /* Set RTS = 1 */
+ }
}
static int sci_txfill(struct uart_port *port)
} else {
for (i = 0; i < count; i++) {
char c = sci_in(port, SCxRDR);
+
status = sci_in(port, SCxSR);
#if defined(CONFIG_CPU_SH3)
/* Skip "chars" during break */
/* Store data and status */
if (status & SCxSR_FER(port)) {
flag = TTY_FRAME;
+ port->icount.frame++;
dev_notice(port->dev, "frame error\n");
} else if (status & SCxSR_PER(port)) {
flag = TTY_PARITY;
+ port->icount.parity++;
dev_notice(port->dev, "parity error\n");
} else
flag = TTY_NORMAL;
*/
if (s->cfg->overrun_bit != SCIx_NOT_SUPPORTED) {
if (status & (1 << s->cfg->overrun_bit)) {
+ port->icount.overrun++;
+
/* overrun error */
if (tty_insert_flip_char(tty, 0, TTY_OVERRUN))
copied++;
struct sci_port *sci_port = to_sci_port(port);
if (!sci_port->break_flag) {
+ port->icount.brk++;
+
sci_port->break_flag = 1;
sci_schedule_break_timer(sci_port);
} else {
/* frame error */
+ port->icount.frame++;
+
if (tty_insert_flip_char(tty, 0, TTY_FRAME))
copied++;
if (status & SCxSR_PER(port)) {
/* parity error */
+ port->icount.parity++;
+
if (tty_insert_flip_char(tty, 0, TTY_PARITY))
copied++;
if ((sci_in(port, SCLSR) & (1 << s->cfg->overrun_bit))) {
sci_out(port, SCLSR, 0);
+ port->icount.overrun++;
+
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
tty_flip_buffer_push(tty);
/* Debounce break */
s->break_flag = 1;
#endif
+
+ port->icount.brk++;
+
/* Notify of BREAK */
if (tty_insert_flip_char(tty, 0, TTY_BREAK))
copied++;
}
}
+static const char *sci_gpio_names[SCIx_NR_FNS] = {
+ "sck", "rxd", "txd", "cts", "rts",
+};
+
+static const char *sci_gpio_str(unsigned int index)
+{
+ return sci_gpio_names[index];
+}
+
+static void __devinit sci_init_gpios(struct sci_port *port)
+{
+ struct uart_port *up = &port->port;
+ int i;
+
+ if (!port->cfg)
+ return;
+
+ for (i = 0; i < SCIx_NR_FNS; i++) {
+ const char *desc;
+ int ret;
+
+ if (!port->cfg->gpios[i])
+ continue;
+
+ desc = sci_gpio_str(i);
+
+ port->gpiostr[i] = kasprintf(GFP_KERNEL, "%s:%s",
+ dev_name(up->dev), desc);
+
+ /*
+ * If we've failed the allocation, we can still continue
+ * on with a NULL string.
+ */
+ if (!port->gpiostr[i])
+ dev_notice(up->dev, "%s string allocation failure\n",
+ desc);
+
+ ret = gpio_request(port->cfg->gpios[i], port->gpiostr[i]);
+ if (unlikely(ret != 0)) {
+ dev_notice(up->dev, "failed %s gpio request\n", desc);
+
+ /*
+ * If we can't get the GPIO for whatever reason,
+ * no point in keeping the verbose string around.
+ */
+ kfree(port->gpiostr[i]);
+ }
+ }
+}
+
+static void sci_free_gpios(struct sci_port *port)
+{
+ int i;
+
+ for (i = 0; i < SCIx_NR_FNS; i++)
+ if (port->cfg->gpios[i]) {
+ gpio_free(port->cfg->gpios[i]);
+ kfree(port->gpiostr[i]);
+ }
+}
+
static unsigned int sci_tx_empty(struct uart_port *port)
{
unsigned short status = sci_in(port, SCxSR);
return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
}
+/*
+ * Modem control is a bit of a mixed bag for SCI(F) ports. Generally
+ * CTS/RTS is supported in hardware by at least one port and controlled
+ * via SCSPTR (SCxPCR for SCIFA/B parts), or external pins (presently
+ * handled via the ->init_pins() op, which is a bit of a one-way street,
+ * lacking any ability to defer pin control -- this will later be
+ * converted over to the GPIO framework).
+ *
+ * Other modes (such as loopback) are supported generically on certain
+ * port types, but not others. For these it's sufficient to test for the
+ * existence of the support register and simply ignore the port type.
+ */
static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- /* This routine is used for seting signals of: DTR, DCD, CTS/RTS */
- /* We use SCIF's hardware for CTS/RTS, so don't need any for that. */
- /* If you have signals for DTR and DCD, please implement here. */
+ if (mctrl & TIOCM_LOOP) {
+ struct plat_sci_reg *reg;
+
+ /*
+ * Standard loopback mode for SCFCR ports.
+ */
+ reg = sci_getreg(port, SCFCR);
+ if (reg->size)
+ sci_out(port, SCFCR, sci_in(port, SCFCR) | 1);
+ }
}
static unsigned int sci_get_mctrl(struct uart_port *port)
{
- /* This routine is used for getting signals of: DTR, DCD, DSR, RI,
- and CTS/RTS */
-
- return TIOCM_DTR | TIOCM_RTS | TIOCM_CTS | TIOCM_DSR;
+ /*
+ * CTS/RTS is handled in hardware when supported, while nothing
+ * else is wired up. Keep it simple and simply assert DSR/CAR.
+ */
+ return TIOCM_DSR | TIOCM_CAR;
}
#ifdef CONFIG_SERIAL_SH_SCI_DMA
static void sci_enable_ms(struct uart_port *port)
{
- /* Nothing here yet .. */
+ /*
+ * Not supported by hardware, always a nop.
+ */
}
static void sci_break_ctl(struct uart_port *port, int break_state)
{
- /* Nothing here yet .. */
+ /*
+ * Not supported by hardware. Most parts couple break and rx
+ * interrupts together, with break detection always enabled.
+ */
}
#ifdef CONFIG_SERIAL_SH_SCI_DMA
static void sci_reset(struct uart_port *port)
{
+ struct plat_sci_reg *reg;
unsigned int status;
do {
sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
- if (port->type != PORT_SCI)
+ reg = sci_getreg(port, SCFCR);
+ if (reg->size)
sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
}
struct ktermios *old)
{
struct sci_port *s = to_sci_port(port);
+ struct plat_sci_reg *reg;
unsigned int baud, smr_val, max_baud;
int t = -1;
- u16 scfcr = 0;
/*
* earlyprintk comes here early on with port->uartclk set to zero.
}
sci_init_pins(port, termios->c_cflag);
- sci_out(port, SCFCR, scfcr | ((termios->c_cflag & CRTSCTS) ? SCFCR_MCE : 0));
+
+ reg = sci_getreg(port, SCFCR);
+ if (reg->size) {
+ unsigned short ctrl = sci_in(port, SCFCR);
+
+ if (s->cfg->capabilities & SCIx_HAVE_RTSCTS) {
+ if (termios->c_cflag & CRTSCTS)
+ ctrl |= SCFCR_MCE;
+ else
+ ctrl &= ~SCFCR_MCE;
+ }
+
+ /*
+ * As we've done a sci_reset() above, ensure we don't
+ * interfere with the FIFOs while toggling MCE. As the
+ * reset values could still be set, simply mask them out.
+ */
+ ctrl &= ~(SCFCR_RFRST | SCFCR_TFRST);
+
+ sci_out(port, SCFCR, ctrl);
+ }
sci_out(port, SCSCR, s->cfg->scscr);
struct uart_port *port = &sci_port->port;
int ret;
+ sci_port->cfg = p;
+
port->ops = &sci_uart_ops;
port->iotype = UPIO_MEM;
port->line = index;
port->dev = &dev->dev;
+ sci_init_gpios(sci_port);
+
pm_runtime_irq_safe(&dev->dev);
pm_runtime_enable(&dev->dev);
}
p->error_mask |= (1 << p->overrun_bit);
}
- sci_port->cfg = p;
-
port->mapbase = p->mapbase;
port->type = p->type;
port->flags = p->flags;
struct uart_port *port = &sci_port->port;
if (uart_console(port)) {
+ struct plat_sci_reg *reg;
+
sci_port->saved_smr = sci_in(port, SCSMR);
sci_port->saved_brr = sci_in(port, SCBRR);
- sci_port->saved_fcr = sci_in(port, SCFCR);
+
+ reg = sci_getreg(port, SCFCR);
+ if (reg->size)
+ sci_port->saved_fcr = sci_in(port, SCFCR);
+ else
+ sci_port->saved_fcr = 0;
}
return 0;
}
sci_reset(port);
sci_out(port, SCSMR, sci_port->saved_smr);
sci_out(port, SCBRR, sci_port->saved_brr);
- sci_out(port, SCFCR, sci_port->saved_fcr);
+
+ if (sci_port->saved_fcr)
+ sci_out(port, SCFCR, sci_port->saved_fcr);
+
sci_out(port, SCSCR, sci_port->cfg->scscr);
}
return 0;
cpufreq_unregister_notifier(&port->freq_transition,
CPUFREQ_TRANSITION_NOTIFIER);
+ sci_free_gpios(port);
+
uart_remove_one_port(&sci_uart_driver, &port->port);
clk_put(port->iclk);