#include <config.h>
-#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) \
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI) \
&& defined(CONFIG_TSI108_ETH)
#if !defined(CONFIG_TSI108_ETH_NUM_PORTS) || (CONFIG_TSI108_ETH_NUM_PORTS > 2)
#endif
#if TSI108_ETH_DEBUG > 0
-#define debug_lev(lev, fmt, args...) if (lev <= TSI108_ETH_DEBUG) printf("%s %d: " fmt, __FUNCTION__, __LINE__, ##args)
+#define debug_lev(lev, fmt, args...) \
+if (lev <= TSI108_ETH_DEBUG) \
+printf ("%s %d: " fmt, __FUNCTION__, __LINE__, ##args)
#else
#define debug_lev(lev, fmt, args...) do{}while(0)
#endif
#define RX_PRINT_ERRORS
#define TX_PRINT_ERRORS
-#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000)
+#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000)
-#define ETH_PORT_OFFSET 0x400
+#define ETH_PORT_OFFSET 0x400
#define __REG32(base, offset) (*((volatile u32 *)((char *)(base) + (offset))))
-#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000)
-#define MAC_CONFIG_1_TX_ENABLE (0x00000001)
-#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002)
-#define MAC_CONFIG_1_RX_ENABLE (0x00000004)
-#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008)
-#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010)
-#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020)
-#define MAC_CONFIG_1_LOOP_BACK (0x00000100)
-#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000)
-#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000)
-#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000)
-#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000)
-#define MAC_CONFIG_1_SIM_RESET (0x40000000)
-#define MAC_CONFIG_1_SOFT_RESET (0x80000000)
-
-#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004)
-#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001)
-#define MAC_CONFIG_2_CRC_ENABLE (0x00000002)
-#define MAC_CONFIG_2_PAD_CRC (0x00000004)
-#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010)
-#define MAC_CONFIG_2_HUGE_FRAME (0x00000020)
-#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8)
-#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12)
-#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */
-#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */
-
-#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010)
-
-#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020)
-#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7)
-#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010)
-#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020)
-#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000)
-
-#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024)
-#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001)
-#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002)
-
-#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028)
-#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c)
-#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030)
-
-#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034)
-#define MII_MGMT_INDICATORS_BUSY (0x00000001)
-#define MII_MGMT_INDICATORS_SCAN (0x00000002)
-#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004)
-
-#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c)
-#define INTERFACE_STATUS_LINK_FAIL (0x00000008)
-#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200)
-
-#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040)
-#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044)
-
-#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200)
-#define PORT_CONTROL_PRI (0x00000001)
-#define PORT_CONTROL_BPT (0x00010000)
-#define PORT_CONTROL_SPD (0x00040000)
-#define PORT_CONTROL_RBC (0x00080000)
-#define PORT_CONTROL_PRB (0x00200000)
-#define PORT_CONTROL_DIS (0x00400000)
-#define PORT_CONTROL_TBI (0x00800000)
-#define PORT_CONTROL_STE (0x10000000)
-#define PORT_CONTROL_ZOR (0x20000000)
-#define PORT_CONTROL_CLR (0x40000000)
-#define PORT_CONTROL_SRT (0x80000000)
-
-#define reg_TX_CONFIG(base) __REG32(base, 0x00000220)
-#define TX_CONFIG_START_Q (0x00000003)
-#define TX_CONFIG_EHP (0x00400000)
-#define TX_CONFIG_CHP (0x00800000)
-#define TX_CONFIG_RST (0x80000000)
-
-#define reg_TX_CONTROL(base) __REG32(base, 0x00000224)
-#define TX_CONTROL_GO (0x00008000)
-#define TX_CONTROL_MP (0x01000000)
-#define TX_CONTROL_EAI (0x20000000)
-#define TX_CONTROL_ABT (0x40000000)
-#define TX_CONTROL_EII (0x80000000)
-
-#define reg_TX_STATUS(base) __REG32(base, 0x00000228)
-#define TX_STATUS_QUEUE_USABLE (0x0000000f)
-#define TX_STATUS_CURR_Q (0x00000300)
-#define TX_STATUS_ACT (0x00008000)
-#define TX_STATUS_QUEUE_IDLE (0x000f0000)
-#define TX_STATUS_EOQ_PENDING (0x0f000000)
-
-#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c)
-#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f)
-#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00)
-#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
-#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
-
-#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230)
+#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000)
+#define MAC_CONFIG_1_TX_ENABLE (0x00000001)
+#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002)
+#define MAC_CONFIG_1_RX_ENABLE (0x00000004)
+#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008)
+#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010)
+#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020)
+#define MAC_CONFIG_1_LOOP_BACK (0x00000100)
+#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000)
+#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000)
+#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000)
+#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000)
+#define MAC_CONFIG_1_SIM_RESET (0x40000000)
+#define MAC_CONFIG_1_SOFT_RESET (0x80000000)
+
+#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004)
+#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001)
+#define MAC_CONFIG_2_CRC_ENABLE (0x00000002)
+#define MAC_CONFIG_2_PAD_CRC (0x00000004)
+#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010)
+#define MAC_CONFIG_2_HUGE_FRAME (0x00000020)
+#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8)
+#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12)
+#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */
+#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */
+
+#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010)
+
+#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020)
+#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7)
+#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010)
+#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020)
+#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000)
+
+#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024)
+#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001)
+#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002)
+
+#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028)
+#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c)
+#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030)
+
+#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034)
+#define MII_MGMT_INDICATORS_BUSY (0x00000001)
+#define MII_MGMT_INDICATORS_SCAN (0x00000002)
+#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004)
+
+#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c)
+#define INTERFACE_STATUS_LINK_FAIL (0x00000008)
+#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200)
+
+#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040)
+#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044)
+
+#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200)
+#define PORT_CONTROL_PRI (0x00000001)
+#define PORT_CONTROL_BPT (0x00010000)
+#define PORT_CONTROL_SPD (0x00040000)
+#define PORT_CONTROL_RBC (0x00080000)
+#define PORT_CONTROL_PRB (0x00200000)
+#define PORT_CONTROL_DIS (0x00400000)
+#define PORT_CONTROL_TBI (0x00800000)
+#define PORT_CONTROL_STE (0x10000000)
+#define PORT_CONTROL_ZOR (0x20000000)
+#define PORT_CONTROL_CLR (0x40000000)
+#define PORT_CONTROL_SRT (0x80000000)
+
+#define reg_TX_CONFIG(base) __REG32(base, 0x00000220)
+#define TX_CONFIG_START_Q (0x00000003)
+#define TX_CONFIG_EHP (0x00400000)
+#define TX_CONFIG_CHP (0x00800000)
+#define TX_CONFIG_RST (0x80000000)
+
+#define reg_TX_CONTROL(base) __REG32(base, 0x00000224)
+#define TX_CONTROL_GO (0x00008000)
+#define TX_CONTROL_MP (0x01000000)
+#define TX_CONTROL_EAI (0x20000000)
+#define TX_CONTROL_ABT (0x40000000)
+#define TX_CONTROL_EII (0x80000000)
+
+#define reg_TX_STATUS(base) __REG32(base, 0x00000228)
+#define TX_STATUS_QUEUE_USABLE (0x0000000f)
+#define TX_STATUS_CURR_Q (0x00000300)
+#define TX_STATUS_ACT (0x00008000)
+#define TX_STATUS_QUEUE_IDLE (0x000f0000)
+#define TX_STATUS_EOQ_PENDING (0x0f000000)
+
+#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c)
+#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f)
+#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00)
+#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
+#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
+
+#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230)
#define reg_TX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000270)
-#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
-#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000)
-#define TX_DIAGNOSTIC_ADDR_AI (0x80000000)
-
-#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274)
-
-#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278)
-#define TX_ERROR_STATUS (0x00000278)
-#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f)
-#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010)
-#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020)
-#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040)
-#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080)
-#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00)
-#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000)
-#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000)
-#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000)
-#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000)
-#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000)
-#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000)
-#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000)
-#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000)
-#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000)
-#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000)
-#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000)
-#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000)
-#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000)
-#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000)
-
-#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280)
-#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
-#define TX_QUEUE_0_CONFIG_BSWP (0x00000400)
-#define TX_QUEUE_0_CONFIG_WSWP (0x00000800)
-#define TX_QUEUE_0_CONFIG_AM (0x00004000)
-#define TX_QUEUE_0_CONFIG_GVI (0x00008000)
-#define TX_QUEUE_0_CONFIG_EEI (0x00010000)
-#define TX_QUEUE_0_CONFIG_ELI (0x00020000)
-#define TX_QUEUE_0_CONFIG_ENI (0x00040000)
-#define TX_QUEUE_0_CONFIG_ESI (0x00080000)
-#define TX_QUEUE_0_CONFIG_EDI (0x00100000)
-
-#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284)
-#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
-#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
-#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
-#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
-
-#define OCN_PORT_HLP 0 /* HLP Interface */
-#define OCN_PORT_PCI_X 1 /* PCI-X Interface */
+#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
+#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000)
+#define TX_DIAGNOSTIC_ADDR_AI (0x80000000)
+
+#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274)
+
+#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278)
+#define TX_ERROR_STATUS (0x00000278)
+#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080)
+#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000)
+#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000)
+#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000)
+#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000)
+#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000)
+#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000)
+#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000)
+
+#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280)
+#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
+#define TX_QUEUE_0_CONFIG_BSWP (0x00000400)
+#define TX_QUEUE_0_CONFIG_WSWP (0x00000800)
+#define TX_QUEUE_0_CONFIG_AM (0x00004000)
+#define TX_QUEUE_0_CONFIG_GVI (0x00008000)
+#define TX_QUEUE_0_CONFIG_EEI (0x00010000)
+#define TX_QUEUE_0_CONFIG_ELI (0x00020000)
+#define TX_QUEUE_0_CONFIG_ENI (0x00040000)
+#define TX_QUEUE_0_CONFIG_ESI (0x00080000)
+#define TX_QUEUE_0_CONFIG_EDI (0x00100000)
+
+#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284)
+#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
+#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
+#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
+#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
+
+#define OCN_PORT_HLP 0 /* HLP Interface */
+#define OCN_PORT_PCI_X 1 /* PCI-X Interface */
#define OCN_PORT_PROCESSOR_MASTER 2 /* Processor Interface (master) */
-#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */
-#define OCN_PORT_MEMORY 4 /* Memory Controller */
-#define OCN_PORT_DMA 5 /* DMA Controller */
-#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */
-#define OCN_PORT_PRINT 7 /* Print Engine Interface */
-
-#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288)
-
-#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c)
-#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
-
-#define reg_RX_CONFIG(base) __REG32(base, 0x00000320)
-#define RX_CONFIG_DEF_Q (0x00000003)
-#define RX_CONFIG_EMF (0x00000100)
-#define RX_CONFIG_EUF (0x00000200)
-#define RX_CONFIG_BFE (0x00000400)
-#define RX_CONFIG_MFE (0x00000800)
-#define RX_CONFIG_UFE (0x00001000)
-#define RX_CONFIG_SE (0x00002000)
-#define RX_CONFIG_ABF (0x00200000)
-#define RX_CONFIG_APE (0x00400000)
-#define RX_CONFIG_CHP (0x00800000)
-#define RX_CONFIG_RST (0x80000000)
-
-#define reg_RX_CONTROL(base) __REG32(base, 0x00000324)
-#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f)
-#define GE_E0_RX_CONTROL_GO (0x00008000)
-#define GE_E0_RX_CONTROL_EAI (0x20000000)
-#define GE_E0_RX_CONTROL_ABT (0x40000000)
-#define GE_E0_RX_CONTROL_EII (0x80000000)
-
-#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c)
-#define RX_EXTENDED_STATUS (0x0000032c)
-#define RX_EXTENDED_STATUS_EOQ (0x0000000f)
-#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001)
-#define RX_EXTENDED_STATUS_EOF (0x00000f00)
-#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
-#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
-
-#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330)
-
-#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370)
-#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
-#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000)
-#define RX_DIAGNOSTIC_ADDR_AI (0x80000000)
-
-#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374)
-
-#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380)
-#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
-#define RX_QUEUE_0_CONFIG_BSWP (0x00000400)
-#define RX_QUEUE_0_CONFIG_WSWP (0x00000800)
-#define RX_QUEUE_0_CONFIG_AM (0x00004000)
-#define RX_QUEUE_0_CONFIG_EEI (0x00010000)
-#define RX_QUEUE_0_CONFIG_ELI (0x00020000)
-#define RX_QUEUE_0_CONFIG_ENI (0x00040000)
-#define RX_QUEUE_0_CONFIG_ESI (0x00080000)
-#define RX_QUEUE_0_CONFIG_EDI (0x00100000)
-
-#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384)
-#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
-#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
-#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
-#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
-
-#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388)
-
-#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c)
-#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
+#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */
+#define OCN_PORT_MEMORY 4 /* Memory Controller */
+#define OCN_PORT_DMA 5 /* DMA Controller */
+#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */
+#define OCN_PORT_PRINT 7 /* Print Engine Interface */
+
+#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288)
+
+#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c)
+#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
+
+#define reg_RX_CONFIG(base) __REG32(base, 0x00000320)
+#define RX_CONFIG_DEF_Q (0x00000003)
+#define RX_CONFIG_EMF (0x00000100)
+#define RX_CONFIG_EUF (0x00000200)
+#define RX_CONFIG_BFE (0x00000400)
+#define RX_CONFIG_MFE (0x00000800)
+#define RX_CONFIG_UFE (0x00001000)
+#define RX_CONFIG_SE (0x00002000)
+#define RX_CONFIG_ABF (0x00200000)
+#define RX_CONFIG_APE (0x00400000)
+#define RX_CONFIG_CHP (0x00800000)
+#define RX_CONFIG_RST (0x80000000)
+
+#define reg_RX_CONTROL(base) __REG32(base, 0x00000324)
+#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f)
+#define GE_E0_RX_CONTROL_GO (0x00008000)
+#define GE_E0_RX_CONTROL_EAI (0x20000000)
+#define GE_E0_RX_CONTROL_ABT (0x40000000)
+#define GE_E0_RX_CONTROL_EII (0x80000000)
+
+#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c)
+#define RX_EXTENDED_STATUS (0x0000032c)
+#define RX_EXTENDED_STATUS_EOQ (0x0000000f)
+#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001)
+#define RX_EXTENDED_STATUS_EOF (0x00000f00)
+#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000)
+#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000)
+
+#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330)
+
+#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370)
+#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f)
+#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000)
+#define RX_DIAGNOSTIC_ADDR_AI (0x80000000)
+
+#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374)
+
+#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380)
+#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f)
+#define RX_QUEUE_0_CONFIG_BSWP (0x00000400)
+#define RX_QUEUE_0_CONFIG_WSWP (0x00000800)
+#define RX_QUEUE_0_CONFIG_AM (0x00004000)
+#define RX_QUEUE_0_CONFIG_EEI (0x00010000)
+#define RX_QUEUE_0_CONFIG_ELI (0x00020000)
+#define RX_QUEUE_0_CONFIG_ENI (0x00040000)
+#define RX_QUEUE_0_CONFIG_ESI (0x00080000)
+#define RX_QUEUE_0_CONFIG_EDI (0x00100000)
+
+#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384)
+#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f)
+#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300)
+#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400)
+#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800)
+
+#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388)
+
+#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c)
+#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000)
/*
* PHY register definitions
*/
/* the first 15 PHY registers are standard. */
-#define PHY_CTRL_REG 0 /* Control Register */
-#define PHY_STATUS_REG 1 /* Status Regiser */
-#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */
-#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */
-#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */
-#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */
-#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */
-#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */
+#define PHY_CTRL_REG 0 /* Control Register */
+#define PHY_STATUS_REG 1 /* Status Regiser */
+#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */
+#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */
+#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */
+#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */
/*
* PHY Register bit masks.
*/
-#define PHY_CTRL_RESET (1 << 15)
-#define PHY_CTRL_LOOPBACK (1 << 14)
-#define PHY_CTRL_SPEED0 (1 << 13)
-#define PHY_CTRL_AN_EN (1 << 12)
-#define PHY_CTRL_PWR_DN (1 << 11)
-#define PHY_CTRL_ISOLATE (1 << 10)
-#define PHY_CTRL_RESTART_AN (1 << 9)
-#define PHY_CTRL_FULL_DUPLEX (1 << 8)
-#define PHY_CTRL_CT_EN (1 << 7)
-#define PHY_CTRL_SPEED1 (1 << 6)
-
-#define PHY_STAT_100BASE_T4 (1 << 15)
-#define PHY_STAT_100BASE_X_FD (1 << 14)
-#define PHY_STAT_100BASE_X_HD (1 << 13)
-#define PHY_STAT_10BASE_T_FD (1 << 12)
-#define PHY_STAT_10BASE_T_HD (1 << 11)
-#define PHY_STAT_100BASE_T2_FD (1 << 10)
-#define PHY_STAT_100BASE_T2_HD (1 << 9)
-#define PHY_STAT_EXT_STAT (1 << 8)
-#define PHY_STAT_RESERVED (1 << 7)
-#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */
-#define PHY_STAT_AN_COMPLETE (1 << 5)
-#define PHY_STAT_REM_FAULT (1 << 4)
-#define PHY_STAT_AN_CAP (1 << 3)
-#define PHY_STAT_LINK_UP (1 << 2)
-#define PHY_STAT_JABBER (1 << 1)
-#define PHY_STAT_EXT_CAP (1 << 0)
-
-#define TBI_CONTROL_2 0x11
-#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001
-#define TBI_CONTROL_2_ENABLE_WRAP 0x0002
-#define TBI_CONTROL_2_G_MII_MODE 0x0010
-#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020
-#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100
-#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000
-#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000
-#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000
-#define TBI_CONTROL_2_SOFT_RESET 0x8000
+#define PHY_CTRL_RESET (1 << 15)
+#define PHY_CTRL_LOOPBACK (1 << 14)
+#define PHY_CTRL_SPEED0 (1 << 13)
+#define PHY_CTRL_AN_EN (1 << 12)
+#define PHY_CTRL_PWR_DN (1 << 11)
+#define PHY_CTRL_ISOLATE (1 << 10)
+#define PHY_CTRL_RESTART_AN (1 << 9)
+#define PHY_CTRL_FULL_DUPLEX (1 << 8)
+#define PHY_CTRL_CT_EN (1 << 7)
+#define PHY_CTRL_SPEED1 (1 << 6)
+
+#define PHY_STAT_100BASE_T4 (1 << 15)
+#define PHY_STAT_100BASE_X_FD (1 << 14)
+#define PHY_STAT_100BASE_X_HD (1 << 13)
+#define PHY_STAT_10BASE_T_FD (1 << 12)
+#define PHY_STAT_10BASE_T_HD (1 << 11)
+#define PHY_STAT_100BASE_T2_FD (1 << 10)
+#define PHY_STAT_100BASE_T2_HD (1 << 9)
+#define PHY_STAT_EXT_STAT (1 << 8)
+#define PHY_STAT_RESERVED (1 << 7)
+#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */
+#define PHY_STAT_AN_COMPLETE (1 << 5)
+#define PHY_STAT_REM_FAULT (1 << 4)
+#define PHY_STAT_AN_CAP (1 << 3)
+#define PHY_STAT_LINK_UP (1 << 2)
+#define PHY_STAT_JABBER (1 << 1)
+#define PHY_STAT_EXT_CAP (1 << 0)
+
+#define TBI_CONTROL_2 0x11
+#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001
+#define TBI_CONTROL_2_ENABLE_WRAP 0x0002
+#define TBI_CONTROL_2_G_MII_MODE 0x0010
+#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020
+#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100
+#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000
+#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000
+#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000
+#define TBI_CONTROL_2_SOFT_RESET 0x8000
/* marvel specific */
-#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */
-#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */
-#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */
+#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */
+#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */
+#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */
/*
* MARVELL 88E1111 PHY register bit masks
*/
/* PHY Specific Status Register (MV1111_EXT_CTRL1_REG) */
-#define SPEC_STAT_SPEED_MASK (3 << 14)
-#define SPEC_STAT_FULL_DUP (1 << 13)
-#define SPEC_STAT_PAGE_RCVD (1 << 12)
-#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */
-#define SPEC_STAT_LINK_UP (1 << 10)
-#define SPEC_STAT_CABLE_LEN_MASK (7 << 7) /* Cable Length (100/1000 modes only) */
-#define SPEC_STAT_MDIX (1 << 6)
-#define SPEC_STAT_POLARITY (1 << 1)
-#define SPEC_STAT_JABBER (1 << 0)
+#define SPEC_STAT_SPEED_MASK (3 << 14)
+#define SPEC_STAT_FULL_DUP (1 << 13)
+#define SPEC_STAT_PAGE_RCVD (1 << 12)
+#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */
+#define SPEC_STAT_LINK_UP (1 << 10)
+#define SPEC_STAT_CABLE_LEN_MASK (7 << 7)/* Cable Length (100/1000 modes only) */
+#define SPEC_STAT_MDIX (1 << 6)
+#define SPEC_STAT_POLARITY (1 << 1)
+#define SPEC_STAT_JABBER (1 << 0)
-#define SPEED_1000 (2 << 14)
-#define SPEED_100 (1 << 14)
-#define SPEED_10 (0 << 14)
+#define SPEED_1000 (2 << 14)
+#define SPEED_100 (1 << 14)
+#define SPEED_10 (0 << 14)
-#define TBI_ADDR 0x1E /* Ten Bit Interface address */
+#define TBI_ADDR 0x1E /* Ten Bit Interface address */
/* negotiated link parameters */
-#define LINK_SPEED_UNKNOWN 0
-#define LINK_SPEED_10 1
-#define LINK_SPEED_100 2
-#define LINK_SPEED_1000 3
+#define LINK_SPEED_UNKNOWN 0
+#define LINK_SPEED_10 1
+#define LINK_SPEED_100 2
+#define LINK_SPEED_1000 3
-#define LINK_DUPLEX_UNKNOWN 0
-#define LINK_DUPLEX_HALF 1
-#define LINK_DUPLEX_FULL 2
+#define LINK_DUPLEX_UNKNOWN 0
+#define LINK_DUPLEX_HALF 1
+#define LINK_DUPLEX_FULL 2
static unsigned int phy_address[] = { 8, 9 };
};
/* last next descriptor address flag */
-#define DMA_DESCR_LAST (1 << 31)
+#define DMA_DESCR_LAST (1 << 31)
/* TX DMA descriptor config status bits */
-#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */
-#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */
-#define DMA_DESCR_TX_PFVLAN (1 << 2)
-#define DMA_DESCR_TX_HUGE (1 << 3)
-#define DMA_DESCR_TX_PAD (1 << 4)
-#define DMA_DESCR_TX_CRC (1 << 5)
-#define DMA_DESCR_TX_DESCR_INT (1 << 14)
-#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000
-#define DMA_DESCR_TX_ONE_COLLISION (1 << 20)
-#define DMA_DESCR_TX_LATE_COLLISION (1 << 24)
-#define DMA_DESCR_TX_UNDERRUN (1 << 25)
-#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26)
-#define DMA_DESCR_TX_OK (1 << 30)
-#define DMA_DESCR_TX_OWNER (1 << 31)
+#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */
+#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */
+#define DMA_DESCR_TX_PFVLAN (1 << 2)
+#define DMA_DESCR_TX_HUGE (1 << 3)
+#define DMA_DESCR_TX_PAD (1 << 4)
+#define DMA_DESCR_TX_CRC (1 << 5)
+#define DMA_DESCR_TX_DESCR_INT (1 << 14)
+#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000
+#define DMA_DESCR_TX_ONE_COLLISION (1 << 20)
+#define DMA_DESCR_TX_LATE_COLLISION (1 << 24)
+#define DMA_DESCR_TX_UNDERRUN (1 << 25)
+#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26)
+#define DMA_DESCR_TX_OK (1 << 30)
+#define DMA_DESCR_TX_OWNER (1 << 31)
/* RX DMA descriptor status bits */
-#define DMA_DESCR_RX_EOF (1 << 0)
-#define DMA_DESCR_RX_SOF (1 << 1)
-#define DMA_DESCR_RX_VTF (1 << 2)
-#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3)
-#define DMA_DESCR_RX_SHORT_FRAME (1 << 4)
-#define DMA_DESCR_RX_HASH_MATCH (1 << 7)
-#define DMA_DESCR_RX_BAD_FRAME (1 << 8)
-#define DMA_DESCR_RX_OVERRUN (1 << 9)
-#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11)
-#define DMA_DESCR_RX_CRC_ERROR (1 << 12)
-#define DMA_DESCR_RX_DESCR_INT (1 << 13)
-#define DMA_DESCR_RX_OWNER (1 << 15)
-
-#define RX_BUFFER_SIZE PKTSIZE
-#define NUM_RX_DESC PKTBUFSRX
+#define DMA_DESCR_RX_EOF (1 << 0)
+#define DMA_DESCR_RX_SOF (1 << 1)
+#define DMA_DESCR_RX_VTF (1 << 2)
+#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3)
+#define DMA_DESCR_RX_SHORT_FRAME (1 << 4)
+#define DMA_DESCR_RX_HASH_MATCH (1 << 7)
+#define DMA_DESCR_RX_BAD_FRAME (1 << 8)
+#define DMA_DESCR_RX_OVERRUN (1 << 9)
+#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11)
+#define DMA_DESCR_RX_CRC_ERROR (1 << 12)
+#define DMA_DESCR_RX_DESCR_INT (1 << 13)
+#define DMA_DESCR_RX_OWNER (1 << 15)
+
+#define RX_BUFFER_SIZE PKTSIZE
+#define NUM_RX_DESC PKTBUFSRX
static struct dma_descriptor tx_descriptor __attribute__ ((aligned(32)));
static struct dma_descriptor rx_descr_array[NUM_RX_DESC]
- __attribute__ ((aligned(32)));
+ __attribute__ ((aligned(32)));
static struct dma_descriptor *rx_descr_current;
-static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis);
-static int tsi108_eth_send(struct eth_device *dev,
+static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis);
+static int tsi108_eth_send (struct eth_device *dev,
volatile void *packet, int length);
-static int tsi108_eth_recv(struct eth_device *dev);
-static void tsi108_eth_halt(struct eth_device *dev);
-static unsigned int read_phy(unsigned int base,
+static int tsi108_eth_recv (struct eth_device *dev);
+static void tsi108_eth_halt (struct eth_device *dev);
+static unsigned int read_phy (unsigned int base,
unsigned int phy_addr, unsigned int phy_reg);
-static void write_phy(unsigned int base,
+static void write_phy (unsigned int base,
unsigned int phy_addr,
unsigned int phy_reg, unsigned int phy_data);
/*
* print phy debug infomation
*/
-static void dump_phy_regs(unsigned int phy_addr)
+static void dump_phy_regs (unsigned int phy_addr)
{
int i;
- printf("PHY %d registers\n", phy_addr);
+ printf ("PHY %d registers\n", phy_addr);
for (i = 0; i <= 30; i++) {
- printf("%2d 0x%04x\n", i, read_phy(ETH_BASE, phy_addr, i));
+ printf ("%2d 0x%04x\n", i, read_phy (ETH_BASE, phy_addr, i));
}
- printf("\n");
+ printf ("\n");
}
#else
/*
* print debug infomation
*/
-static void tx_diag_regs(unsigned int base)
+static void tx_diag_regs (unsigned int base)
{
int i;
unsigned long dummy;
- printf("TX diagnostics registers\n");
+ printf ("TX diagnostics registers\n");
reg_TX_DIAGNOSTIC_ADDR(base) = 0x00 | TX_DIAGNOSTIC_ADDR_AI;
- udelay(1000);
+ udelay (1000);
dummy = reg_TX_DIAGNOSTIC_DATA(base);
for (i = 0x00; i <= 0x05; i++) {
- udelay(1000);
- printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
}
reg_TX_DIAGNOSTIC_ADDR(base) = 0x40 | TX_DIAGNOSTIC_ADDR_AI;
- udelay(1000);
+ udelay (1000);
dummy = reg_TX_DIAGNOSTIC_DATA(base);
for (i = 0x40; i <= 0x47; i++) {
- udelay(1000);
- printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base));
}
- printf("\n");
+ printf ("\n");
}
#else
/*
* print debug infomation
*/
-static void rx_diag_regs(unsigned int base)
+static void rx_diag_regs (unsigned int base)
{
int i;
unsigned long dummy;
- printf("RX diagnostics registers\n");
+ printf ("RX diagnostics registers\n");
reg_RX_DIAGNOSTIC_ADDR(base) = 0x00 | RX_DIAGNOSTIC_ADDR_AI;
- udelay(1000);
+ udelay (1000);
dummy = reg_RX_DIAGNOSTIC_DATA(base);
for (i = 0x00; i <= 0x05; i++) {
- udelay(1000);
- printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
}
reg_RX_DIAGNOSTIC_ADDR(base) = 0x40 | RX_DIAGNOSTIC_ADDR_AI;
- udelay(1000);
+ udelay (1000);
dummy = reg_RX_DIAGNOSTIC_DATA(base);
for (i = 0x08; i <= 0x0a; i++) {
- udelay(1000);
- printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
+ udelay (1000);
+ printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base));
}
- printf("\n");
+ printf ("\n");
}
#else
/*
* print debug infomation
*/
-static void debug_mii_regs(unsigned int base)
+static void debug_mii_regs (unsigned int base)
{
- printf("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base));
- printf("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base));
- printf("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base));
- printf("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base));
- printf("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base));
- printf("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base));
- printf("\n");
+ printf ("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base));
+ printf ("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base));
+ printf ("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base));
+ printf ("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base));
+ printf ("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base));
+ printf ("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base));
+ printf ("\n");
}
#else
/*
* Wait until the phy bus is non-busy
*/
-static void phy_wait(unsigned int base, unsigned int condition)
+static void phy_wait (unsigned int base, unsigned int condition)
{
int timeout;
timeout = 0;
while (reg_MII_MGMT_INDICATORS(base) & condition) {
- udelay(10);
+ udelay (10);
if (++timeout > 10000) {
- printf("ERROR: timeout waiting for phy bus (%d)\n",
+ printf ("ERROR: timeout waiting for phy bus (%d)\n",
condition);
break;
}
/*
* read phy register
*/
-static unsigned int read_phy(unsigned int base,
+static unsigned int read_phy (unsigned int base,
unsigned int phy_addr, unsigned int phy_reg)
{
unsigned int value;
- phy_wait(base, MII_MGMT_INDICATORS_BUSY);
+ phy_wait (base, MII_MGMT_INDICATORS_BUSY);
reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg;
reg_MII_MGMT_COMMAND(base) = MII_MGMT_COMMAND_READ_CYCLE;
/* wait for the read to complete */
- phy_wait(base,
+ phy_wait (base,
MII_MGMT_INDICATORS_NOT_VALID | MII_MGMT_INDICATORS_BUSY);
value = reg_MII_MGMT_STATUS(base);
/*
* write phy register
*/
-static void write_phy(unsigned int base,
+static void write_phy (unsigned int base,
unsigned int phy_addr,
unsigned int phy_reg, unsigned int phy_data)
{
- phy_wait(base, MII_MGMT_INDICATORS_BUSY);
+ phy_wait (base, MII_MGMT_INDICATORS_BUSY);
reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg;
/*
* configure the marvell 88e1111 phy
*/
-static int marvell_88e_phy_config(struct eth_device *dev, int *speed,
+static int marvell_88e_phy_config (struct eth_device *dev, int *speed,
int *duplex)
{
unsigned long base;
phy_addr = (unsigned long)dev->priv;
/* Take the PHY out of reset. */
- write_phy(ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET);
+ write_phy (ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET);
/* Wait for the reset process to complete. */
- udelay(10);
+ udelay (10);
timeout = 0;
while ((phy_status =
- read_phy(ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) {
- udelay(10);
+ read_phy (ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) {
+ udelay (10);
if (++timeout > 10000) {
- printf("ERROR: timeout waiting for phy reset\n");
+ printf ("ERROR: timeout waiting for phy reset\n");
break;
}
}
/* TBI Configuration. */
- write_phy(base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE |
+ write_phy (base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE |
TBI_CONTROL_2_RECEIVE_CLOCK_SELECT);
/* Wait for the link to be established. */
timeout = 0;
do {
- udelay(20000);
- phy_status = read_phy(ETH_BASE, phy_addr, PHY_STATUS_REG);
+ udelay (20000);
+ phy_status = read_phy (ETH_BASE, phy_addr, PHY_STATUS_REG);
if (++timeout > 100) {
debug_lev(1, "ERROR: unable to establish link!!!\n");
break;
}
} while ((phy_status & PHY_STAT_LINK_UP) == 0);
- if ((phy_status & PHY_STAT_LINK_UP) == 0) {
+ if ((phy_status & PHY_STAT_LINK_UP) == 0)
return 0;
- }
value = 0;
- phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
+ phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
if (phy_spec_status & SPEC_STAT_RESOLVED) {
switch (phy_spec_status & SPEC_STAT_SPEED_MASK) {
case SPEED_1000:
if (phy_spec_status & SPEC_STAT_FULL_DUP) {
phy_duplex = LINK_DUPLEX_FULL;
value |= PHY_CTRL_FULL_DUPLEX;
- } else {
+ } else
phy_duplex = LINK_DUPLEX_HALF;
- }
}
/* set TBI speed */
- write_phy(base, TBI_ADDR, PHY_CTRL_REG, value);
- write_phy(base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060);
+ write_phy (base, TBI_ADDR, PHY_CTRL_REG, value);
+ write_phy (base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060);
#if TSI108_ETH_DEBUG > 0
- printf("%s link is up", dev->name);
- phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
+ printf ("%s link is up", dev->name);
+ phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG);
if (phy_spec_status & SPEC_STAT_RESOLVED) {
switch (phy_speed) {
case LINK_SPEED_1000:
- printf(", 1000 Mbps");
+ printf (", 1000 Mbps");
break;
case LINK_SPEED_100:
- printf(", 100 Mbps");
+ printf (", 100 Mbps");
break;
case LINK_SPEED_10:
- printf(", 10 Mbps");
+ printf (", 10 Mbps");
break;
}
- if (phy_duplex == LINK_DUPLEX_FULL) {
- printf(", Full duplex");
- } else {
- printf(", Half duplex");
- }
+ if (phy_duplex == LINK_DUPLEX_FULL)
+ printf (", Full duplex");
+ else
+ printf (", Half duplex");
}
- printf("\n");
+ printf ("\n");
#endif
- dump_phy_regs(TBI_ADDR);
- if (speed) {
+ dump_phy_regs (TBI_ADDR);
+ if (speed)
*speed = phy_speed;
- }
- if (duplex) {
+ if (duplex)
*duplex = phy_duplex;
- }
return 1;
}
*
* register the tsi108 ethernet controllers with the multi-ethernet system
*/
-int tsi108_eth_initialize(bd_t * bis)
+int tsi108_eth_initialize (bd_t * bis)
{
struct eth_device *dev;
int index;
for (index = 0; index < CONFIG_TSI108_ETH_NUM_PORTS; index++) {
dev = (struct eth_device *)malloc(sizeof(struct eth_device));
- sprintf(dev->name, "TSI108_eth%d", index);
+ sprintf (dev->name, "TSI108_eth%d", index);
dev->iobase = ETH_BASE + (index * ETH_PORT_OFFSET);
dev->priv = (void *)(phy_address[index]);
/*
* probe for and initialize a single ethernet interface
*/
-static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis)
+static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis)
{
unsigned long base;
unsigned long value;
reg_STATION_ADDRESS_2(base) = (dev->enetaddr[1] << 24) |
(dev->enetaddr[0] << 16);
- if (marvell_88e_phy_config(dev, &speed, &duplex) == 0) {
+ if (marvell_88e_phy_config(dev, &speed, &duplex) == 0)
return 0;
- }
value =
MAC_CONFIG_2_PREAMBLE_LENGTH(7) | MAC_CONFIG_2_PAD_CRC |
MAC_CONFIG_2_CRC_ENABLE;
- if (speed == LINK_SPEED_1000) {
+ if (speed == LINK_SPEED_1000)
value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_BYTE);
- } else {
+ else {
value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_NIBBLE);
reg_PORT_CONTROL(base) |= PORT_CONTROL_SPD;
}
if (duplex == LINK_DUPLEX_FULL) {
value |= MAC_CONFIG_2_FULL_DUPLEX;
reg_PORT_CONTROL(base) &= ~PORT_CONTROL_BPT;
- } else {
+ } else
reg_PORT_CONTROL(base) |= PORT_CONTROL_BPT;
- }
reg_MAC_CONFIG_2(base) = value;
reg_RX_CONFIG(base) = RX_CONFIG_SE;
/*
* send a packet
*/
-static int tsi108_eth_send(struct eth_device *dev,
+static int tsi108_eth_send (struct eth_device *dev,
volatile void *packet, int length)
{
unsigned long base;
(unsigned long)tx_descr +
sizeof(struct dma_descriptor));
- if (timeout != 0) {
- udelay(15);
- }
+ if (timeout != 0)
+ udelay (15);
if (++timeout > 10000) {
tx_diag_regs(base);
debug_lev(1,
status = le32_to_cpu(tx_descr->config_status);
if ((status & DMA_DESCR_TX_OK) == 0) {
#ifdef TX_PRINT_ERRORS
- printf("TX packet error: 0x%08x\n %s%s%s%s\n", status,
+ printf ("TX packet error: 0x%08x\n %s%s%s%s\n", status,
status & DMA_DESCR_TX_OK ? "tx error, " : "",
status & DMA_DESCR_TX_RETRY_LIMIT ?
"retry limit reached, " : "",
#endif
}
- debug_lev(9, "sending packet %d\n", length);
+ debug_lev (9, "sending packet %d\n", length);
tx_descr->start_addr0 = cpu_to_le32((vuint32) packet);
tx_descr->start_addr1 = 0;
tx_descr->next_descr_addr0 = 0;
/*
* Check for received packets and send them up the protocal stack
*/
-static int tsi108_eth_recv(struct eth_device *dev)
+static int tsi108_eth_recv (struct eth_device *dev)
{
struct dma_descriptor *rx_descr;
unsigned long base;
base = dev->iobase;
/* make sure we see the changes made by the DMA engine */
- invalidate_dcache_range((unsigned long)rx_descr_array,
+ invalidate_dcache_range ((unsigned long)rx_descr_array,
(unsigned long)rx_descr_array +
sizeof(rx_descr_array));
status = le32_to_cpu(rx_descr->config_status);
if (status & DMA_DESCR_RX_BAD_FRAME) {
#ifdef RX_PRINT_ERRORS
- printf("RX packet error: 0x%08x\n %s%s%s%s%s%s\n",
+ printf ("RX packet error: 0x%08x\n %s%s%s%s%s%s\n",
status,
status & DMA_DESCR_RX_FRAME_IS_TYPE ? "too big, "
: "",
/*** process packet ***/
buffer =
(volatile uchar
- *)(le32_to_cpu(rx_descr->start_addr0));
- NetReceive(buffer, length);
+ *)(le32_to_cpu (rx_descr->start_addr0));
+ NetReceive (buffer, length);
- invalidate_dcache_range((unsigned long)buffer,
+ invalidate_dcache_range ((unsigned long)buffer,
(unsigned long)buffer +
RX_BUFFER_SIZE);
}
/* Give this buffer back to the DMA engine */
rx_descr->vlan_byte_count = 0;
- rx_descr->config_status = cpu_to_le32((RX_BUFFER_SIZE << 16) |
+ rx_descr->config_status = cpu_to_le32 ((RX_BUFFER_SIZE << 16) |
DMA_DESCR_RX_OWNER);
/* move descriptor pointer forward */
rx_descr =
(struct dma_descriptor
- *)(le32_to_cpu(rx_descr->next_descr_addr0));
- if (rx_descr == 0) {
+ *)(le32_to_cpu (rx_descr->next_descr_addr0));
+ if (rx_descr == 0)
rx_descr = &rx_descr_array[0];
- }
}
/* remember where we are for next time */
rx_descr_current = rx_descr;
/*
* disable an ethernet interface
*/
-static void tsi108_eth_halt(struct eth_device *dev)
+static void tsi108_eth_halt (struct eth_device *dev)
{
unsigned long base;
projects / platform / kernel / u-boot.git / blobdiff