Convert CONFIG_PL011_SERIAL et al to Kconfig

[platform/kernel/u-boot.git] / drivers / sysreset / Kconfig

diff --git a/drivers/sysreset/Kconfig b/drivers/sysreset/Kconfig
index d456f0c..f6d6003 100644 (file)
--- a/drivers/sysreset/Kconfig
+++ b/drivers/sysreset/Kconfig
@@ -33,9 +33,32 @@ config TPL_SYSRESET
 
 if SYSRESET
 
+config SYSRESET_CMD_RESET
+       bool "sysreset implementation of the reset command"
+       default y
+       help
+         Enable sysreset implementation of the reset command.
+
+if CMD_POWEROFF
+
+config SYSRESET_CMD_POWEROFF
+       bool "sysreset implementation of the poweroff command"
+       help
+         This should be selected by the appropriate PMIC driver if
+         the poweroff command is enabled.
+
+endif
+
+config POWEROFF_GPIO
+       bool "Enable support for GPIO poweroff driver"
+       select DM_GPIO
+       help
+         Support for system poweroff using a GPIO pin. This can be used
+         for systems having a single GPIO to trigger a system poweroff.
+
 config SYSRESET_GPIO
        bool "Enable support for GPIO reset driver"
-       select GPIO
+       select DM_GPIO
        help
          Reset support via GPIO pin connected reset logic. This is used for
          example on Microblaze where reset logic can be controlled via GPIO
@@ -47,13 +70,47 @@ config SYSRESET_MICROBLAZE
        help
          This is soft reset on Microblaze which does jump to 0x0 address.
 
+config SYSRESET_OCTEON
+       bool "Enable support for Marvell Octeon SoC family"
+       depends on ARCH_OCTEON
+       help
+         This enables the system reset driver support for Marvell Octeon
+         SoCs.
+
 config SYSRESET_PSCI
        bool "Enable support for PSCI System Reset"
        depends on ARM_PSCI_FW
+       select SPL_ARM_PSCI_FW if SPL
        help
          Enable PSCI SYSTEM_RESET function call.  To use this, PSCI firmware
          must be running on your system.
 
+config SYSRESET_SBI
+       bool "Enable support for SBI System Reset"
+       depends on RISCV_SMODE && SBI_V02
+       select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
+       help
+         Enable system reset and poweroff via the SBI system reset extension.
+         The extension was introduced in version 0.3 of the SBI specification.
+
+         If the SBI implementation provides the extension, is board specific.
+         The RISC-V platform specification mandates the extension for rich
+         operating system platforms.
+
+config SYSRESET_SOCFPGA
+       bool "Enable support for Intel SOCFPGA family"
+       depends on ARCH_SOCFPGA && (TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10)
+       help
+         This enables the system reset driver support for Intel SOCFPGA SoCs
+         (Cyclone 5, Arria 5 and Arria 10).
+
+config SYSRESET_SOCFPGA_SOC64
+       bool "Enable support for Intel SOCFPGA SoC64 family (Stratix10/Agilex)"
+       depends on ARCH_SOCFPGA && TARGET_SOCFPGA_SOC64
+       help
+         This enables the system reset driver support for Intel SOCFPGA
+         SoC64 SoCs.
+
 config SYSRESET_TI_SCI
        bool "TI System Control Interface (TI SCI) system reset driver"
        depends on TI_SCI_PROTOCOL
@@ -61,8 +118,6 @@ config SYSRESET_TI_SCI
          This enables the system reset driver support over TI System Control
          Interface available on some new TI's SoCs.
 
-endif
-
 config SYSRESET_SYSCON
        bool "Enable support for mfd syscon reboot driver"
        select REGMAP
@@ -76,15 +131,42 @@ config SYSRESET_WATCHDOG
        help
          Reboot support for generic watchdog reset.
 
+config SYSRESET_WATCHDOG_AUTO
+       bool "Automatically register first watchdog with sysreset"
+       depends on SYSRESET_WATCHDOG
+       help
+         If enabled, the first watchdog (as selected by the watchdog uclass)
+         will automatically be registered with the watchdog reboot driver.
+
+config SYSRESET_RESETCTL
+       bool "Enable support for reset controller reboot driver"
+       select DM_RESET
+       help
+         Reboot support using generic reset controller.
+
 config SYSRESET_X86
        bool "Enable support for x86 processor reboot driver"
        depends on X86
        help
          Reboot support for generic x86 processor reset.
 
-config SYSRESET_MCP83XX
+config SYSRESET_SPL_X86
+       bool "Enable support for x86 processor reboot driver in SPL"
+       depends on X86
+       help
+         Reboot support for generic x86 processor reset in SPL.
+
+config SYSRESET_TPL_X86
+       bool "Enable support for x86 processor reboot driver in TPL"
+       depends on X86
+       help
+         Reboot support for generic x86 processor reset in TPL.
+
+config SYSRESET_MPC83XX
        bool "Enable support MPC83xx SoC family reboot driver"
        help
          Reboot support for NXP MPC83xx SoCs.
 
+endif
+
 endmenu