common: Drop linux/bitops.h from common header
[platform/kernel/u-boot.git] / drivers / spi / ich.c
index fbb58c7..7405062 100644 (file)
@@ -5,28 +5,49 @@
  * This file is derived from the flashrom project.
  */
 
+#define LOG_CATEGORY   UCLASS_SPI
+
 #include <common.h>
+#include <bootstage.h>
+#include <div64.h>
 #include <dm.h>
+#include <dt-structs.h>
 #include <errno.h>
+#include <log.h>
 #include <malloc.h>
 #include <pch.h>
 #include <pci.h>
 #include <pci_ids.h>
 #include <spi.h>
-#include <asm/io.h>
+#include <spi_flash.h>
 #include <spi-mem.h>
-#include <div64.h>
+#include <spl.h>
+#include <asm/fast_spi.h>
+#include <asm/io.h>
+#include <asm/mtrr.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/sizes.h>
 
 #include "ich.h"
 
-DECLARE_GLOBAL_DATA_PTR;
-
 #ifdef DEBUG_TRACE
 #define debug_trace(fmt, args...) debug(fmt, ##args)
 #else
 #define debug_trace(x, args...)
 #endif
 
+struct ich_spi_platdata {
+#if CONFIG_IS_ENABLED(OF_PLATDATA)
+       struct dtd_intel_fast_spi dtplat;
+#endif
+       enum ich_version ich_version;   /* Controller version, 7 or 9 */
+       bool lockdown;                  /* lock down controller settings? */
+       ulong mmio_base;                /* Base of MMIO registers */
+       pci_dev_t bdf;                  /* PCI address used by of-platdata */
+       bool hwseq;                     /* Use hardware sequencing (not s/w) */
+};
+
 static u8 ich_readb(struct ich_spi_priv *priv, int reg)
 {
        u8 value = readb(priv->base + reg);
@@ -89,22 +110,27 @@ static void ich_set_bbar(struct ich_spi_priv *ctlr, uint32_t minaddr)
        const uint32_t bbar_mask = 0x00ffff00;
        uint32_t ichspi_bbar;
 
-       minaddr &= bbar_mask;
-       ichspi_bbar = ich_readl(ctlr, ctlr->bbar) & ~bbar_mask;
-       ichspi_bbar |= minaddr;
-       ich_writel(ctlr, ichspi_bbar, ctlr->bbar);
+       if (ctlr->bbar) {
+               minaddr &= bbar_mask;
+               ichspi_bbar = ich_readl(ctlr, ctlr->bbar) & ~bbar_mask;
+               ichspi_bbar |= minaddr;
+               ich_writel(ctlr, ichspi_bbar, ctlr->bbar);
+       }
 }
 
 /* @return 1 if the SPI flash supports the 33MHz speed */
-static int ich9_can_do_33mhz(struct udevice *dev)
+static bool ich9_can_do_33mhz(struct udevice *dev)
 {
+       struct ich_spi_priv *priv = dev_get_priv(dev);
        u32 fdod, speed;
 
+       if (!CONFIG_IS_ENABLED(PCI))
+               return false;
        /* Observe SPI Descriptor Component Section 0 */
-       dm_pci_write_config32(dev->parent, 0xb0, 0x1000);
+       dm_pci_write_config32(priv->pch, 0xb0, 0x1000);
 
        /* Extract the Write/Erase SPI Frequency from descriptor */
-       dm_pci_read_config32(dev->parent, 0xb4, &fdod);
+       dm_pci_read_config32(priv->pch, 0xb4, &fdod);
 
        /* Bits 23:21 have the fast read clock frequency, 0=20MHz, 1=33MHz */
        speed = (fdod >> 21) & 7;
@@ -112,67 +138,6 @@ static int ich9_can_do_33mhz(struct udevice *dev)
        return speed == 1;
 }
 
-static int ich_init_controller(struct udevice *dev,
-                              struct ich_spi_platdata *plat,
-                              struct ich_spi_priv *ctlr)
-{
-       ulong sbase_addr;
-       void *sbase;
-
-       /* SBASE is similar */
-       pch_get_spi_base(dev->parent, &sbase_addr);
-       sbase = (void *)sbase_addr;
-       debug("%s: sbase=%p\n", __func__, sbase);
-
-       if (plat->ich_version == ICHV_7) {
-               struct ich7_spi_regs *ich7_spi = sbase;
-
-               ctlr->opmenu = offsetof(struct ich7_spi_regs, opmenu);
-               ctlr->menubytes = sizeof(ich7_spi->opmenu);
-               ctlr->optype = offsetof(struct ich7_spi_regs, optype);
-               ctlr->addr = offsetof(struct ich7_spi_regs, spia);
-               ctlr->data = offsetof(struct ich7_spi_regs, spid);
-               ctlr->databytes = sizeof(ich7_spi->spid);
-               ctlr->status = offsetof(struct ich7_spi_regs, spis);
-               ctlr->control = offsetof(struct ich7_spi_regs, spic);
-               ctlr->bbar = offsetof(struct ich7_spi_regs, bbar);
-               ctlr->preop = offsetof(struct ich7_spi_regs, preop);
-               ctlr->base = ich7_spi;
-       } else if (plat->ich_version == ICHV_9) {
-               struct ich9_spi_regs *ich9_spi = sbase;
-
-               ctlr->opmenu = offsetof(struct ich9_spi_regs, opmenu);
-               ctlr->menubytes = sizeof(ich9_spi->opmenu);
-               ctlr->optype = offsetof(struct ich9_spi_regs, optype);
-               ctlr->addr = offsetof(struct ich9_spi_regs, faddr);
-               ctlr->data = offsetof(struct ich9_spi_regs, fdata);
-               ctlr->databytes = sizeof(ich9_spi->fdata);
-               ctlr->status = offsetof(struct ich9_spi_regs, ssfs);
-               ctlr->control = offsetof(struct ich9_spi_regs, ssfc);
-               ctlr->speed = ctlr->control + 2;
-               ctlr->bbar = offsetof(struct ich9_spi_regs, bbar);
-               ctlr->preop = offsetof(struct ich9_spi_regs, preop);
-               ctlr->bcr = offsetof(struct ich9_spi_regs, bcr);
-               ctlr->pr = &ich9_spi->pr[0];
-               ctlr->base = ich9_spi;
-       } else {
-               debug("ICH SPI: Unrecognised ICH version %d\n",
-                     plat->ich_version);
-               return -EINVAL;
-       }
-
-       /* Work out the maximum speed we can support */
-       ctlr->max_speed = 20000000;
-       if (plat->ich_version == ICHV_9 && ich9_can_do_33mhz(dev))
-               ctlr->max_speed = 33000000;
-       debug("ICH SPI: Version ID %d detected at %p, speed %ld\n",
-             plat->ich_version, ctlr->base, ctlr->max_speed);
-
-       ich_set_bbar(ctlr, 0);
-
-       return 0;
-}
-
 static void spi_lock_down(struct ich_spi_platdata *plat, void *sbase)
 {
        if (plat->ich_version == ICHV_7) {
@@ -233,8 +198,7 @@ static int spi_setup_opcode(struct ich_spi_priv *ctlr, struct spi_trans *trans,
                }
 
                if (opcode_index == ctlr->menubytes) {
-                       printf("ICH SPI: Opcode %x not found\n",
-                              trans->opcode);
+                       debug("ICH SPI: Opcode %x not found\n", trans->opcode);
                        return -EINVAL;
                }
 
@@ -242,8 +206,8 @@ static int spi_setup_opcode(struct ich_spi_priv *ctlr, struct spi_trans *trans,
                optype = (optypes >> (opcode_index * 2)) & 0x3;
 
                if (optype != trans->type) {
-                       printf("ICH SPI: Transaction doesn't fit type %d\n",
-                              optype);
+                       debug("ICH SPI: Transaction doesn't fit type %d\n",
+                             optype);
                        return -ENOSPC;
                }
                return opcode_index;
@@ -274,9 +238,9 @@ static int ich_status_poll(struct ich_spi_priv *ctlr, u16 bitmask,
                }
                udelay(10);
        }
+       debug("ICH SPI: SCIP timeout, read %x, expected %x, wts %x %x\n",
+             status, bitmask, wait_til_set, status & bitmask);
 
-       printf("ICH SPI: SCIP timeout, read %x, expected %x\n",
-              status, bitmask);
        return -ETIMEDOUT;
 }
 
@@ -295,7 +259,8 @@ static void ich_spi_config_opcode(struct udevice *dev)
        ich_writel(ctlr, SPI_OPMENU_UPPER, ctlr->opmenu + sizeof(u32));
 }
 
-static int ich_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
+static int ich_spi_exec_op_swseq(struct spi_slave *slave,
+                                const struct spi_mem_op *op)
 {
        struct udevice *bus = dev_get_parent(slave->dev);
        struct ich_spi_platdata *plat = dev_get_platdata(bus);
@@ -466,6 +431,220 @@ static int ich_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
        return 0;
 }
 
+/*
+ * Ensure read/write xfer len is not greater than SPIBAR_FDATA_FIFO_SIZE and
+ * that the operation does not cross page boundary.
+ */
+static uint get_xfer_len(u32 offset, int len, int page_size)
+{
+       uint xfer_len = min(len, SPIBAR_FDATA_FIFO_SIZE);
+       uint bytes_left = ALIGN(offset, page_size) - offset;
+
+       if (bytes_left)
+               xfer_len = min(xfer_len, bytes_left);
+
+       return xfer_len;
+}
+
+/* Fill FDATAn FIFO in preparation for a write transaction */
+static void fill_xfer_fifo(struct fast_spi_regs *regs, const void *data,
+                          uint len)
+{
+       memcpy(regs->fdata, data, len);
+}
+
+/* Drain FDATAn FIFO after a read transaction populates data */
+static void drain_xfer_fifo(struct fast_spi_regs *regs, void *dest, uint len)
+{
+       memcpy(dest, regs->fdata, len);
+}
+
+/* Fire up a transfer using the hardware sequencer */
+static void start_hwseq_xfer(struct fast_spi_regs *regs, uint hsfsts_cycle,
+                            uint offset, uint len)
+{
+       /* Make sure all W1C status bits get cleared */
+       u32 hsfsts;
+
+       hsfsts = readl(&regs->hsfsts_ctl);
+       hsfsts &= ~(HSFSTS_FCYCLE_MASK | HSFSTS_FDBC_MASK);
+       hsfsts |= HSFSTS_AEL | HSFSTS_FCERR | HSFSTS_FDONE;
+
+       /* Set up transaction parameters */
+       hsfsts |= hsfsts_cycle << HSFSTS_FCYCLE_SHIFT;
+       hsfsts |= ((len - 1) << HSFSTS_FDBC_SHIFT) & HSFSTS_FDBC_MASK;
+       hsfsts |= HSFSTS_FGO;
+
+       writel(offset, &regs->faddr);
+       writel(hsfsts, &regs->hsfsts_ctl);
+}
+
+static int wait_for_hwseq_xfer(struct fast_spi_regs *regs, uint offset)
+{
+       ulong start;
+       u32 hsfsts;
+
+       start = get_timer(0);
+       do {
+               hsfsts = readl(&regs->hsfsts_ctl);
+               if (hsfsts & HSFSTS_FCERR) {
+                       debug("SPI transaction error at offset %x HSFSTS = %08x\n",
+                             offset, hsfsts);
+                       return -EIO;
+               }
+               if (hsfsts & HSFSTS_AEL)
+                       return -EPERM;
+
+               if (hsfsts & HSFSTS_FDONE)
+                       return 0;
+       } while (get_timer(start) < SPIBAR_HWSEQ_XFER_TIMEOUT_MS);
+
+       debug("SPI transaction timeout at offset %x HSFSTS = %08x, timer %d\n",
+             offset, hsfsts, (uint)get_timer(start));
+
+       return -ETIMEDOUT;
+}
+
+/**
+ * exec_sync_hwseq_xfer() - Execute flash transfer by hardware sequencing
+ *
+ * This waits until complete or timeout
+ *
+ * @regs: SPI registers
+ * @hsfsts_cycle: Cycle type (enum hsfsts_cycle_t)
+ * @offset: Offset to access
+ * @len: Number of bytes to transfer (can be 0)
+ * @return 0 if OK, -EIO on flash-cycle error (FCERR), -EPERM on access error
+ *     (AEL), -ETIMEDOUT on timeout
+ */
+static int exec_sync_hwseq_xfer(struct fast_spi_regs *regs, uint hsfsts_cycle,
+                               uint offset, uint len)
+{
+       start_hwseq_xfer(regs, hsfsts_cycle, offset, len);
+
+       return wait_for_hwseq_xfer(regs, offset);
+}
+
+static int ich_spi_exec_op_hwseq(struct spi_slave *slave,
+                                const struct spi_mem_op *op)
+{
+       struct spi_flash *flash = dev_get_uclass_priv(slave->dev);
+       struct udevice *bus = dev_get_parent(slave->dev);
+       struct ich_spi_priv *priv = dev_get_priv(bus);
+       struct fast_spi_regs *regs = priv->base;
+       uint page_size;
+       uint offset;
+       int cycle;
+       uint len;
+       bool out;
+       int ret;
+       u8 *buf;
+
+       offset = op->addr.val;
+       len = op->data.nbytes;
+
+       switch (op->cmd.opcode) {
+       case SPINOR_OP_RDID:
+               cycle = HSFSTS_CYCLE_RDID;
+               break;
+       case SPINOR_OP_READ_FAST:
+               cycle = HSFSTS_CYCLE_READ;
+               break;
+       case SPINOR_OP_PP:
+               cycle = HSFSTS_CYCLE_WRITE;
+               break;
+       case SPINOR_OP_WREN:
+               /* Nothing needs to be done */
+               return 0;
+       case SPINOR_OP_WRSR:
+               cycle = HSFSTS_CYCLE_WR_STATUS;
+               break;
+       case SPINOR_OP_RDSR:
+               cycle = HSFSTS_CYCLE_RD_STATUS;
+               break;
+       case SPINOR_OP_WRDI:
+               return 0;  /* ignore */
+       case SPINOR_OP_BE_4K:
+               cycle = HSFSTS_CYCLE_4K_ERASE;
+               ret = exec_sync_hwseq_xfer(regs, cycle, offset, 0);
+               return ret;
+       default:
+               debug("Unknown cycle %x\n", op->cmd.opcode);
+               return -EINVAL;
+       };
+
+       out = op->data.dir == SPI_MEM_DATA_OUT;
+       buf = out ? (u8 *)op->data.buf.out : op->data.buf.in;
+       page_size = flash->page_size ? : 256;
+
+       while (len) {
+               uint xfer_len = get_xfer_len(offset, len, page_size);
+
+               if (out)
+                       fill_xfer_fifo(regs, buf, xfer_len);
+
+               ret = exec_sync_hwseq_xfer(regs, cycle, offset, xfer_len);
+               if (ret)
+                       return ret;
+
+               if (!out)
+                       drain_xfer_fifo(regs, buf, xfer_len);
+
+               offset += xfer_len;
+               buf += xfer_len;
+               len -= xfer_len;
+       }
+
+       return 0;
+}
+
+static int ich_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
+{
+       struct udevice *bus = dev_get_parent(slave->dev);
+       struct ich_spi_platdata *plat = dev_get_platdata(bus);
+       int ret;
+
+       bootstage_start(BOOTSTAGE_ID_ACCUM_SPI, "fast_spi");
+       if (plat->hwseq)
+               ret = ich_spi_exec_op_hwseq(slave, op);
+       else
+               ret = ich_spi_exec_op_swseq(slave, op);
+       bootstage_accum(BOOTSTAGE_ID_ACCUM_SPI);
+
+       return ret;
+}
+
+static int ich_get_mmap_bus(struct udevice *bus, ulong *map_basep,
+                           uint *map_sizep, uint *offsetp)
+{
+       pci_dev_t spi_bdf;
+
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+       struct pci_child_platdata *pplat = dev_get_parent_platdata(bus);
+
+       spi_bdf = pplat->devfn;
+#else
+       struct ich_spi_platdata *plat = dev_get_platdata(bus);
+
+       /*
+        * We cannot rely on plat->bdf being set up yet since this method can
+        * be called before the device is probed. Use the of-platdata directly
+        * instead.
+        */
+       spi_bdf = pci_ofplat_get_devfn(plat->dtplat.reg[0]);
+#endif
+
+       return fast_spi_get_bios_mmap(spi_bdf, map_basep, map_sizep, offsetp);
+}
+
+static int ich_get_mmap(struct udevice *dev, ulong *map_basep, uint *map_sizep,
+                       uint *offsetp)
+{
+       struct udevice *bus = dev_get_parent(dev);
+
+       return ich_get_mmap_bus(bus, map_basep, map_sizep, offsetp);
+}
+
 static int ich_spi_adjust_size(struct spi_slave *slave, struct spi_mem_op *op)
 {
        unsigned int page_offset;
@@ -480,9 +659,11 @@ static int ich_spi_adjust_size(struct spi_slave *slave, struct spi_mem_op *op)
                page_offset = do_div(aux, ICH_BOUNDARY);
        }
 
-       if (op->data.dir == SPI_MEM_DATA_IN && slave->max_read_size) {
-               op->data.nbytes = min(ICH_BOUNDARY - page_offset,
-                                     slave->max_read_size);
+       if (op->data.dir == SPI_MEM_DATA_IN) {
+               if (slave->max_read_size) {
+                       op->data.nbytes = min(ICH_BOUNDARY - page_offset,
+                                             slave->max_read_size);
+               }
        } else if (slave->max_write_size) {
                op->data.nbytes = min(ICH_BOUNDARY - page_offset,
                                      slave->max_write_size);
@@ -493,26 +674,18 @@ static int ich_spi_adjust_size(struct spi_slave *slave, struct spi_mem_op *op)
        return 0;
 }
 
-static int ich_spi_xfer(struct udevice *dev, unsigned int bitlen,
-                       const void *dout, void *din, unsigned long flags)
-{
-       printf("ICH SPI: Only supports memory operations\n");
-       return -1;
-}
-
-static int ich_spi_probe(struct udevice *dev)
+static int ich_protect_lockdown(struct udevice *dev)
 {
        struct ich_spi_platdata *plat = dev_get_platdata(dev);
        struct ich_spi_priv *priv = dev_get_priv(dev);
-       uint8_t bios_cntl;
-       int ret;
+       int ret = -ENOSYS;
 
-       ret = ich_init_controller(dev, plat, priv);
-       if (ret)
-               return ret;
        /* Disable the BIOS write protect so write commands are allowed */
-       ret = pch_set_spi_protect(dev->parent, false);
+       if (priv->pch)
+               ret = pch_set_spi_protect(priv->pch, false);
        if (ret == -ENOSYS) {
+               u8 bios_cntl;
+
                bios_cntl = ich_readb(priv, priv->bcr);
                bios_cntl &= ~BIT(5);   /* clear Enable InSMM_STS (EISS) */
                bios_cntl |= 1;         /* Write Protect Disable (WPD) */
@@ -529,6 +702,111 @@ static int ich_spi_probe(struct udevice *dev)
                spi_lock_down(plat, priv->base);
        }
 
+       return 0;
+}
+
+static int ich_init_controller(struct udevice *dev,
+                              struct ich_spi_platdata *plat,
+                              struct ich_spi_priv *ctlr)
+{
+       if (spl_phase() == PHASE_TPL) {
+               struct ich_spi_platdata *plat = dev_get_platdata(dev);
+               int ret;
+
+               ret = fast_spi_early_init(plat->bdf, plat->mmio_base);
+               if (ret)
+                       return ret;
+       }
+
+       ctlr->base = (void *)plat->mmio_base;
+       if (plat->ich_version == ICHV_7) {
+               struct ich7_spi_regs *ich7_spi = ctlr->base;
+
+               ctlr->opmenu = offsetof(struct ich7_spi_regs, opmenu);
+               ctlr->menubytes = sizeof(ich7_spi->opmenu);
+               ctlr->optype = offsetof(struct ich7_spi_regs, optype);
+               ctlr->addr = offsetof(struct ich7_spi_regs, spia);
+               ctlr->data = offsetof(struct ich7_spi_regs, spid);
+               ctlr->databytes = sizeof(ich7_spi->spid);
+               ctlr->status = offsetof(struct ich7_spi_regs, spis);
+               ctlr->control = offsetof(struct ich7_spi_regs, spic);
+               ctlr->bbar = offsetof(struct ich7_spi_regs, bbar);
+               ctlr->preop = offsetof(struct ich7_spi_regs, preop);
+       } else if (plat->ich_version == ICHV_9) {
+               struct ich9_spi_regs *ich9_spi = ctlr->base;
+
+               ctlr->opmenu = offsetof(struct ich9_spi_regs, opmenu);
+               ctlr->menubytes = sizeof(ich9_spi->opmenu);
+               ctlr->optype = offsetof(struct ich9_spi_regs, optype);
+               ctlr->addr = offsetof(struct ich9_spi_regs, faddr);
+               ctlr->data = offsetof(struct ich9_spi_regs, fdata);
+               ctlr->databytes = sizeof(ich9_spi->fdata);
+               ctlr->status = offsetof(struct ich9_spi_regs, ssfs);
+               ctlr->control = offsetof(struct ich9_spi_regs, ssfc);
+               ctlr->speed = ctlr->control + 2;
+               ctlr->bbar = offsetof(struct ich9_spi_regs, bbar);
+               ctlr->preop = offsetof(struct ich9_spi_regs, preop);
+               ctlr->bcr = offsetof(struct ich9_spi_regs, bcr);
+               ctlr->pr = &ich9_spi->pr[0];
+       } else if (plat->ich_version == ICHV_APL) {
+       } else {
+               debug("ICH SPI: Unrecognised ICH version %d\n",
+                     plat->ich_version);
+               return -EINVAL;
+       }
+
+       /* Work out the maximum speed we can support */
+       ctlr->max_speed = 20000000;
+       if (plat->ich_version == ICHV_9 && ich9_can_do_33mhz(dev))
+               ctlr->max_speed = 33000000;
+       debug("ICH SPI: Version ID %d detected at %lx, speed %ld\n",
+             plat->ich_version, plat->mmio_base, ctlr->max_speed);
+
+       ich_set_bbar(ctlr, 0);
+
+       return 0;
+}
+
+static int ich_cache_bios_region(struct udevice *dev)
+{
+       ulong map_base;
+       uint map_size;
+       uint offset;
+       ulong base;
+       int ret;
+
+       ret = ich_get_mmap_bus(dev, &map_base, &map_size, &offset);
+       if (ret)
+               return ret;
+
+       /* Don't use WRBACK since we are not supposed to write to SPI flash */
+       base = SZ_4G - map_size;
+       mtrr_set_next_var(MTRR_TYPE_WRPROT, base, map_size);
+       log_debug("BIOS cache base=%lx, size=%x\n", base, (uint)map_size);
+
+       return 0;
+}
+
+static int ich_spi_probe(struct udevice *dev)
+{
+       struct ich_spi_platdata *plat = dev_get_platdata(dev);
+       struct ich_spi_priv *priv = dev_get_priv(dev);
+       int ret;
+
+       ret = ich_init_controller(dev, plat, priv);
+       if (ret)
+               return ret;
+
+       if (spl_phase() == PHASE_TPL) {
+               /* Cache the BIOS to speed things up */
+               ret = ich_cache_bios_region(dev);
+               if (ret)
+                       return ret;
+       } else {
+               ret = ich_protect_lockdown(dev);
+               if (ret)
+                       return ret;
+       }
        priv->cur_speed = priv->max_speed;
 
        return 0;
@@ -570,9 +848,11 @@ static int ich_spi_child_pre_probe(struct udevice *dev)
 
        /*
         * Yes this controller can only write a small number of bytes at
-        * once! The limit is typically 64 bytes.
+        * once! The limit is typically 64 bytes. For hardware sequencing a
+        * a loop is used to get around this.
         */
-       slave->max_write_size = priv->databytes;
+       if (!plat->hwseq)
+               slave->max_write_size = priv->databytes;
        /*
         * ICH 7 SPI controller only supports array read command
         * and byte program command for SST flash
@@ -586,23 +866,37 @@ static int ich_spi_child_pre_probe(struct udevice *dev)
 static int ich_spi_ofdata_to_platdata(struct udevice *dev)
 {
        struct ich_spi_platdata *plat = dev_get_platdata(dev);
-       int node = dev_of_offset(dev);
-       int ret;
 
-       ret = fdt_node_check_compatible(gd->fdt_blob, node, "intel,ich7-spi");
-       if (ret == 0) {
-               plat->ich_version = ICHV_7;
-       } else {
-               ret = fdt_node_check_compatible(gd->fdt_blob, node,
-                                               "intel,ich9-spi");
-               if (ret == 0)
-                       plat->ich_version = ICHV_9;
-       }
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+       struct ich_spi_priv *priv = dev_get_priv(dev);
 
-       plat->lockdown = fdtdec_get_bool(gd->fdt_blob, node,
-                                        "intel,spi-lock-down");
+       /* Find a PCH if there is one */
+       uclass_first_device(UCLASS_PCH, &priv->pch);
+       if (!priv->pch)
+               priv->pch = dev_get_parent(dev);
+
+       plat->ich_version = dev_get_driver_data(dev);
+       plat->lockdown = dev_read_bool(dev, "intel,spi-lock-down");
+       if (plat->ich_version == ICHV_APL) {
+               plat->mmio_base = dm_pci_read_bar32(dev, 0);
+       } else  {
+               /* SBASE is similar */
+               pch_get_spi_base(priv->pch, &plat->mmio_base);
+       }
+       /*
+        * Use an int so that the property is present in of-platdata even
+        * when false.
+        */
+       plat->hwseq = dev_read_u32_default(dev, "intel,hardware-seq", 0);
+#else
+       plat->ich_version = ICHV_APL;
+       plat->mmio_base = plat->dtplat.early_regs[0];
+       plat->bdf = pci_ofplat_get_devfn(plat->dtplat.reg[0]);
+       plat->hwseq = plat->dtplat.intel_hardware_seq;
+#endif
+       debug("%s: mmio_base=%lx\n", __func__, plat->mmio_base);
 
-       return ret;
+       return 0;
 }
 
 static const struct spi_controller_mem_ops ich_controller_mem_ops = {
@@ -612,10 +906,11 @@ static const struct spi_controller_mem_ops ich_controller_mem_ops = {
 };
 
 static const struct dm_spi_ops ich_spi_ops = {
-       .xfer           = ich_spi_xfer,
+       /* xfer is not supported */
        .set_speed      = ich_spi_set_speed,
        .set_mode       = ich_spi_set_mode,
        .mem_ops        = &ich_controller_mem_ops,
+       .get_mmap       = ich_get_mmap,
        /*
         * cs_info is not needed, since we require all chip selects to be
         * in the device tree explicitly
@@ -623,13 +918,14 @@ static const struct dm_spi_ops ich_spi_ops = {
 };
 
 static const struct udevice_id ich_spi_ids[] = {
-       { .compatible = "intel,ich7-spi" },
-       { .compatible = "intel,ich9-spi" },
+       { .compatible = "intel,ich7-spi", ICHV_7 },
+       { .compatible = "intel,ich9-spi", ICHV_9 },
+       { .compatible = "intel,fast-spi", ICHV_APL },
        { }
 };
 
-U_BOOT_DRIVER(ich_spi) = {
-       .name   = "ich_spi",
+U_BOOT_DRIVER(intel_fast_spi) = {
+       .name   = "intel_fast_spi",
        .id     = UCLASS_SPI,
        .of_match = ich_spi_ids,
        .ops    = &ich_spi_ops,