* modified to use CONFIG_SYS_ISA_MEM and new defines
*/
-#include <config.h>
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
#include <ns16550.h>
+#include <serial.h>
#include <watchdog.h>
#include <linux/types.h>
#include <asm/io.h>
+DECLARE_GLOBAL_DATA_PTR;
+
#define UART_LCRVAL UART_LCR_8N1 /* 8 data, 1 stop, no parity */
#define UART_MCRVAL (UART_MCR_DTR | \
UART_MCR_RTS) /* RTS/DTR */
#define UART_FCRVAL (UART_FCR_FIFO_EN | \
UART_FCR_RXSR | \
UART_FCR_TXSR) /* Clear & enable FIFOs */
+
+#ifndef CONFIG_DM_SERIAL
#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
#define serial_out(x, y) outb(x, (ulong)y)
#define serial_in(y) inb((ulong)y)
#define serial_out(x, y) writeb(x, y)
#define serial_in(y) readb(y)
#endif
+#endif /* !CONFIG_DM_SERIAL */
+
+#if defined(CONFIG_SOC_KEYSTONE)
+#define UART_REG_VAL_PWREMU_MGMT_UART_DISABLE 0
+#define UART_REG_VAL_PWREMU_MGMT_UART_ENABLE ((1 << 14) | (1 << 13) | (1 << 0))
+#undef UART_MCRVAL
+#ifdef CONFIG_SERIAL_HW_FLOW_CONTROL
+#define UART_MCRVAL (UART_MCR_RTS | UART_MCR_AFE)
+#else
+#define UART_MCRVAL (UART_MCR_RTS)
+#endif
+#endif
#ifndef CONFIG_SYS_NS16550_IER
#define CONFIG_SYS_NS16550_IER 0x00
#endif /* CONFIG_SYS_NS16550_IER */
+#ifdef CONFIG_DM_SERIAL
+static void ns16550_writeb(NS16550_t port, int offset, int value)
+{
+ struct ns16550_platdata *plat = port->plat;
+ unsigned char *addr;
+
+ offset *= 1 << plat->reg_shift;
+ addr = map_sysmem(plat->base, 0) + offset;
+ /*
+ * As far as we know it doesn't make sense to support selection of
+ * these options at run-time, so use the existing CONFIG options.
+ */
+#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
+ outb(value, (ulong)addr);
+#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_SYS_BIG_ENDIAN)
+ out_le32(addr, value);
+#elif defined(CONFIG_SYS_NS16550_MEM32) && defined(CONFIG_SYS_BIG_ENDIAN)
+ out_be32(addr, value);
+#elif defined(CONFIG_SYS_BIG_ENDIAN)
+ writeb(value, addr + (1 << plat->reg_shift) - 1);
+#else
+ writeb(value, addr);
+#endif
+}
+
+static int ns16550_readb(NS16550_t port, int offset)
+{
+ struct ns16550_platdata *plat = port->plat;
+ unsigned char *addr;
+
+ offset *= 1 << plat->reg_shift;
+ addr = map_sysmem(plat->base, 0) + offset;
+#ifdef CONFIG_SYS_NS16550_PORT_MAPPED
+ return inb((ulong)addr);
+#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_SYS_BIG_ENDIAN)
+ return in_le32(addr);
+#elif defined(CONFIG_SYS_NS16550_MEM32) && defined(CONFIG_SYS_BIG_ENDIAN)
+ return in_be32(addr);
+#elif defined(CONFIG_SYS_BIG_ENDIAN)
+ return readb(addr + (1 << plat->reg_shift) - 1);
+#else
+ return readb(addr);
+#endif
+}
+
+/* We can clean these up once everything is moved to driver model */
+#define serial_out(value, addr) \
+ ns16550_writeb(com_port, addr - (unsigned char *)com_port, value)
+#define serial_in(addr) \
+ ns16550_readb(com_port, addr - (unsigned char *)com_port)
+#endif
+
+int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate)
+{
+ const unsigned int mode_x_div = 16;
+
+#ifdef CONFIG_OMAP1510
+ /* If can't cleanly clock 115200 set div to 1 */
+ if ((clock == 12000000) && (baudrate == 115200)) {
+ port->osc_12m_sel = OSC_12M_SEL; /* enable 6.5 * divisor */
+ return 1; /* return 1 for base divisor */
+ }
+ port->osc_12m_sel = 0; /* clear if previsouly set */
+#endif
+
+ return DIV_ROUND_CLOSEST(clock, mode_x_div * baudrate);
+}
+
+static void NS16550_setbrg(NS16550_t com_port, int baud_divisor)
+{
+ serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
+ serial_out(baud_divisor & 0xff, &com_port->dll);
+ serial_out((baud_divisor >> 8) & 0xff, &com_port->dlm);
+ serial_out(UART_LCRVAL, &com_port->lcr);
+}
+
void NS16550_init(NS16550_t com_port, int baud_divisor)
{
+#if (defined(CONFIG_SPL_BUILD) && \
+ (defined(CONFIG_OMAP34XX) || defined(CONFIG_OMAP44XX)))
+ /*
+ * On some OMAP3/OMAP4 devices when UART3 is configured for boot mode
+ * before SPL starts only THRE bit is set. We have to empty the
+ * transmitter before initialization starts.
+ */
+ if ((serial_in(&com_port->lsr) & (UART_LSR_TEMT | UART_LSR_THRE))
+ == UART_LSR_THRE) {
+ if (baud_divisor != -1)
+ NS16550_setbrg(com_port, baud_divisor);
+ serial_out(0, &com_port->mdr1);
+ }
+#endif
+
+ while (!(serial_in(&com_port->lsr) & UART_LSR_TEMT))
+ ;
+
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
-#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \
- defined(CONFIG_AM33XX)
+#if defined(CONFIG_OMAP) || defined(CONFIG_AM33XX) || \
+ defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX)
serial_out(0x7, &com_port->mdr1); /* mode select reset TL16C750*/
#endif
- serial_out(UART_LCR_BKSE | UART_LCRVAL, (ulong)&com_port->lcr);
- serial_out(0, &com_port->dll);
- serial_out(0, &com_port->dlm);
- serial_out(UART_LCRVAL, &com_port->lcr);
+ NS16550_setbrg(com_port, 0);
serial_out(UART_MCRVAL, &com_port->mcr);
serial_out(UART_FCRVAL, &com_port->fcr);
- serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
- serial_out(baud_divisor & 0xff, &com_port->dll);
- serial_out((baud_divisor >> 8) & 0xff, &com_port->dlm);
- serial_out(UART_LCRVAL, &com_port->lcr);
-#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \
- defined(CONFIG_AM33XX) || defined(CONFIG_SOC_DA8XX)
+ if (baud_divisor != -1)
+ NS16550_setbrg(com_port, baud_divisor);
+#if defined(CONFIG_OMAP) || \
+ defined(CONFIG_AM33XX) || defined(CONFIG_SOC_DA8XX) || \
+ defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX)
-#if defined(CONFIG_APTIX)
- /* /13 mode so Aptix 6MHz can hit 115200 */
- serial_out(3, &com_port->mdr1);
-#else
/* /16 is proper to hit 115200 with 48MHz */
serial_out(0, &com_port->mdr1);
-#endif
#endif /* CONFIG_OMAP */
+#if defined(CONFIG_SOC_KEYSTONE)
+ serial_out(UART_REG_VAL_PWREMU_MGMT_UART_ENABLE, &com_port->regC);
+#endif
}
#ifndef CONFIG_NS16550_MIN_FUNCTIONS
void NS16550_reinit(NS16550_t com_port, int baud_divisor)
{
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
- serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
- serial_out(0, &com_port->dll);
- serial_out(0, &com_port->dlm);
- serial_out(UART_LCRVAL, &com_port->lcr);
+ NS16550_setbrg(com_port, 0);
serial_out(UART_MCRVAL, &com_port->mcr);
serial_out(UART_FCRVAL, &com_port->fcr);
- serial_out(UART_LCR_BKSE, &com_port->lcr);
- serial_out(baud_divisor & 0xff, &com_port->dll);
- serial_out((baud_divisor >> 8) & 0xff, &com_port->dlm);
- serial_out(UART_LCRVAL, &com_port->lcr);
+ NS16550_setbrg(com_port, baud_divisor);
}
#endif /* CONFIG_NS16550_MIN_FUNCTIONS */
}
#endif /* CONFIG_NS16550_MIN_FUNCTIONS */
+
+#ifdef CONFIG_DM_SERIAL
+static int ns16550_serial_putc(struct udevice *dev, const char ch)
+{
+ struct NS16550 *const com_port = dev_get_priv(dev);
+
+ if (!(serial_in(&com_port->lsr) & UART_LSR_THRE))
+ return -EAGAIN;
+ serial_out(ch, &com_port->thr);
+
+ /*
+ * Call watchdog_reset() upon newline. This is done here in putc
+ * since the environment code uses a single puts() to print the complete
+ * environment upon "printenv". So we can't put this watchdog call
+ * in puts().
+ */
+ if (ch == '\n')
+ WATCHDOG_RESET();
+
+ return 0;
+}
+
+static int ns16550_serial_pending(struct udevice *dev, bool input)
+{
+ struct NS16550 *const com_port = dev_get_priv(dev);
+
+ if (input)
+ return serial_in(&com_port->lsr) & UART_LSR_DR ? 1 : 0;
+ else
+ return serial_in(&com_port->lsr) & UART_LSR_THRE ? 0 : 1;
+}
+
+static int ns16550_serial_getc(struct udevice *dev)
+{
+ struct NS16550 *const com_port = dev_get_priv(dev);
+
+ if (!(serial_in(&com_port->lsr) & UART_LSR_DR))
+ return -EAGAIN;
+
+ return serial_in(&com_port->rbr);
+}
+
+static int ns16550_serial_setbrg(struct udevice *dev, int baudrate)
+{
+ struct NS16550 *const com_port = dev_get_priv(dev);
+ struct ns16550_platdata *plat = com_port->plat;
+ int clock_divisor;
+
+ clock_divisor = ns16550_calc_divisor(com_port, plat->clock, baudrate);
+
+ NS16550_setbrg(com_port, clock_divisor);
+
+ return 0;
+}
+
+int ns16550_serial_probe(struct udevice *dev)
+{
+ struct NS16550 *const com_port = dev_get_priv(dev);
+
+ com_port->plat = dev_get_platdata(dev);
+ NS16550_init(com_port, -1);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF_CONTROL
+int ns16550_serial_ofdata_to_platdata(struct udevice *dev)
+{
+ struct ns16550_platdata *plat = dev->platdata;
+ fdt_addr_t addr;
+
+ addr = fdtdec_get_addr(gd->fdt_blob, dev->of_offset, "reg");
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ plat->base = addr;
+ plat->reg_shift = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+ "reg-shift", 1);
+
+ return 0;
+}
+#endif
+
+const struct dm_serial_ops ns16550_serial_ops = {
+ .putc = ns16550_serial_putc,
+ .pending = ns16550_serial_pending,
+ .getc = ns16550_serial_getc,
+ .setbrg = ns16550_serial_setbrg,
+};
+#endif /* CONFIG_DM_SERIAL */