+#
+# Serial device configuration
+#
+
+menu "Serial drivers"
+
+config REQUIRE_SERIAL_CONSOLE
+ bool "Require a serial port for console"
+ # Running without a serial console is not supported by the
+ # non-dm serial code
+ depends on DM_SERIAL
+ default y
+ help
+ Require a serial port for the console, and panic if none is found
+ during serial port initialization (default y). Set this to n on
+ boards which have no debug serial port whatsoever.
+
config DM_SERIAL
bool "Enable Driver Model for serial drivers"
depends on DM
will need to provide parameters to make this work. The driver will
be available until the real driver model serial is running.
+config DEBUG_EFI_CONSOLE
+ bool "EFI"
+ depends on EFI_APP
+ help
+ Select this to enable a debug console which calls back to EFI to
+ output to the console. This can be useful for early debugging of
+ U-Boot when running on top of EFI (Extensive Firmware Interface).
+ This is a type of BIOS used by PCs.
+
+config DEBUG_UART_S5P
+ bool "Samsung S5P"
+ help
+ Select this to enable a debug UART using the serial_s5p driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
endchoice
config DEBUG_UART_BASE
value. Use this value to specify the shift to use, where 0=byte
registers, 2=32-bit word registers, etc.
+config DEBUG_UART_BOARD_INIT
+ bool "Enable board-specific debug UART init"
+ depends on DEBUG_UART
+ help
+ Some boards need to set things up before the debug UART can be used.
+ On these boards a call to debug_uart_init() is insufficient. When
+ this option is enabled, the function board_debug_uart_init() will
+ be called when debug_uart_init() is called. You can put any code
+ here that is needed to set up the UART ready for use, such as set
+ pin multiplexing or enable clocks.
+
+config ROCKCHIP_SERIAL
+ bool "Rockchip on-chip UART support"
+ depends on ARCH_ROCKCHIP && DM_SERIAL
+ help
+ Select this to enable a debug UART for Rockchip devices. This uses
+ the ns16550 driver. You will need to #define CONFIG_SYS_NS16550 in
+ your board config header. The clock input is automatically set to
+ use the oscillator (24MHz).
+
+config SANDBOX_SERIAL
+ bool "Sandbox UART support"
+ depends on SANDBOX
+ help
+ Select this to enable a seral UART for sandbox. This is required to
+ operate correctly, otherwise you will see no serial output from
+ sandbox. The emulated UART will display to the console and console
+ input will be fed into the UART. This allows you to interact with
+ U-Boot.
+
+ The operation of the console is controlled by the -t command-line
+ flag. In raw mode, U-Boot sees all characters from the terminal
+ before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
+ is processed by the terminal, and terminates U-Boot. Valid options
+ are:
+
+ -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
+ -t raw Raw mode, Ctrl-C is processed by U-Boot
+ -t cooked Cooked mode, Ctrl-C terminates
+
config UNIPHIER_SERIAL
bool "Support for UniPhier on-chip UART"
- depends on ARCH_UNIPHIER && DM_SERIAL
+ depends on ARCH_UNIPHIER
help
If you have a UniPhier based board and want to use the on-chip
serial ports, say Y to this option. If unsure, say N.
+
+config X86_SERIAL
+ bool "Support for 16550 serial port on x86 machines"
+ depends on X86
+ default y
+ help
+ Most x86 machines have a ns16550 UART or compatible. This can be
+ enabled in the device tree with the correct input clock frequency
+ provided (default 1843200). Enable this to obtain serial console
+ output.
+
+endmenu