menuconfig PHYLIB
bool "Ethernet PHY (physical media interface) support"
+ depends on NET
help
Enable Ethernet PHY (physical media interface) support.
if PHYLIB
+config PHY_ADDR_ENABLE
+ bool "Limit phy address"
+ default y if ARCH_SUNXI
+ help
+ Select this if you want to control which phy address is used
+
+if PHY_ADDR_ENABLE
+config PHY_ADDR
+ int "PHY address"
+ default 1 if ARCH_SUNXI
+ default 0
+ help
+ The address of PHY on MII bus. Usually in range of 0 to 31.
+endif
+
+config B53_SWITCH
+ bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
+ help
+ Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
+ This currently supports BCM53125 and similar models.
+
+if B53_SWITCH
+
+config B53_CPU_PORT
+ int "CPU port"
+ default 8
+
+config B53_PHY_PORTS
+ hex "Bitmask of PHY ports"
+
+endif # B53_SWITCH
+
config MV88E61XX_SWITCH
- bool "Marvel MV88E61xx Ethernet switch PHY support."
+ bool "Marvell MV88E61xx Ethernet switch PHY support."
+
+if MV88E61XX_SWITCH
+
+config MV88E61XX_CPU_PORT
+ int "CPU Port"
+
+config MV88E61XX_PHY_PORTS
+ hex "Bitmask of PHY Ports"
+
+config MV88E61XX_FIXED_PORTS
+ hex "Bitmask of PHYless serdes Ports"
+
+endif # MV88E61XX_SWITCH
config PHYLIB_10G
bool "Generic 10G PHY support"
-config PHY_AQUANTIA
+menuconfig PHY_AQUANTIA
bool "Aquantia Ethernet PHYs support"
+ select PHY_GIGE
+ select PHYLIB_10G
+
+config PHY_AQUANTIA_UPLOAD_FW
+ bool "Aquantia firmware loading support"
+ default n
+ depends on PHY_AQUANTIA
+ help
+ Aquantia PHYs use firmware which can be either loaded automatically
+ from storage directly attached to the phy or loaded by the boot loader
+ via MDIO commands. The firmware is loaded from a file, specified by
+ the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options.
+
+config PHY_AQUANTIA_FW_PART
+ string "Aquantia firmware partition"
+ depends on PHY_AQUANTIA_UPLOAD_FW
+ help
+ Partition containing the firmware file.
+
+config PHY_AQUANTIA_FW_NAME
+ string "Aquantia firmware filename"
+ depends on PHY_AQUANTIA_UPLOAD_FW
+ help
+ Firmware filename.
config PHY_ATHEROS
bool "Atheros Ethernet PHYs support"
config PHY_CORTINA
bool "Cortina Ethernet PHYs support"
+choice
+ prompt "Location of the Cortina firmware"
+ default SYS_CORTINA_FW_IN_NOR
+ depends on PHY_CORTINA
+
+config SYS_CORTINA_FW_IN_MMC
+ bool "Cortina firmware in MMC"
+
+config SYS_CORTINA_FW_IN_NAND
+ bool "Cortina firmware in NAND flash"
+
+config SYS_CORTINA_FW_IN_NOR
+ bool "Cortina firmware in NOR flash"
+
+config SYS_CORTINA_FW_IN_REMOTE
+ bool "Cortina firmware in remote device"
+
+config SYS_CORTINA_FW_IN_SPIFLASH
+ bool "Cortina firmware in SPI flash"
+
+endchoice
+
config PHY_DAVICOM
bool "Davicom Ethernet PHYs support"
config PHY_MARVELL
bool "Marvell Ethernet PHYs support"
+config PHY_MESON_GXL
+ bool "Amlogic Meson GXL Internal PHY support"
+
config PHY_MICREL
bool "Micrel Ethernet PHYs support"
+ help
+ Enable support for the GbE PHYs manufactured by Micrel (now
+ a part of Microchip). This includes drivers for the KSZ804, KSZ8031,
+ KSZ8051, KSZ8081, KSZ8895, KSZ886x and KSZ8721 (if "Micrel KSZ8xxx
+ family support" is selected) and the KSZ9021 and KSZ9031 (if "Micrel
+ KSZ90x1 family support" is selected).
+
+if PHY_MICREL
+
+config PHY_MICREL_KSZ9021
+ bool
+ select PHY_MICREL_KSZ90X1
+
+config PHY_MICREL_KSZ9031
+ bool
+ select PHY_MICREL_KSZ90X1
+
+config PHY_MICREL_KSZ90X1
+ bool "Micrel KSZ90x1 family support"
+ select PHY_GIGE
+ help
+ Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
+ enabled, the extended register read/write for KSZ90x1 PHYs
+ is supported through the 'mdio' command and any RGMII signal
+ delays configured in the device tree will be applied to the
+ PHY during initialization.
+
+config PHY_MICREL_KSZ8XXX
+ bool "Micrel KSZ8xxx family support"
+ help
+ Enable support for the 8000 series 10/100 PHYs manufactured by Micrel
+ (now a part of Microchip). This includes drivers for the KSZ804,
+ KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
+
+endif # PHY_MICREL
config PHY_MSCC
bool "Microsemi Corp Ethernet PHYs support"
config PHY_REALTEK
bool "Realtek Ethernet PHYs support"
+config RTL8211E_PINE64_GIGABIT_FIX
+ bool "Fix gigabit throughput on some Pine64+ models"
+ depends on PHY_REALTEK
+ help
+ Configure the Realtek RTL8211E found on some Pine64+ models differently to
+ fix throughput on Gigabit links, turning off all internal delays in the
+ process. The settings that this touches are not documented in the CONFREG
+ section of the RTL8211E datasheet, but come from Realtek by way of the
+ Pine64 engineering team.
+
config RTL8211X_PHY_FORCE_MASTER
bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
depends on PHY_REALTEK
If unsure, say N.
+config RTL8211F_PHY_FORCE_EEE_RXC_ON
+ bool "Ethernet PHY RTL8211F: do not stop receiving the xMII clock during LPI"
+ depends on PHY_REALTEK
+ default n
+ help
+ The IEEE 802.3az-2010 (EEE) standard provides a protocol to coordinate
+ transitions to/from a lower power consumption level (Low Power Idle
+ mode) based on link utilization. When no packets are being
+ transmitted, the system goes to Low Power Idle mode to save power.
+
+ Under particular circumstances this setting can cause issues where
+ the PHY is unable to transmit or receive any packet when in LPI mode.
+ The problem is caused when the PHY is configured to stop receiving
+ the xMII clock while it is signaling LPI. For some PHYs the bit
+ configuring this behavior is set by the Linux kernel, causing the
+ issue in U-Boot on reboot if the PHY retains the register value.
+
+ Default n, which means that the PHY state is not changed. To work
+ around the issues, change this setting to y.
+
config PHY_SMSC
bool "Microchip(SMSC) Ethernet PHYs support"
config PHY_TI
bool "Texas Instruments Ethernet PHYs support"
+ ---help---
+ Adds PHY registration support for TI PHYs.
+
+config PHY_TI_DP83867
+ select PHY_TI
+ bool "Texas Instruments Ethernet DP83867 PHY support"
+ ---help---
+ Adds support for the TI DP83867 1Gbit PHY.
+
+config PHY_TI_GENERIC
+ select PHY_TI
+ bool "Texas Instruments Generic Ethernet PHYs support"
+ ---help---
+ Adds support for Generic TI PHYs that don't need special handling but
+ the PHY name is associated with a PHY ID.
config PHY_VITESSE
bool "Vitesse Ethernet PHYs support"
config PHY_XILINX
bool "Xilinx Ethernet PHYs support"
+config PHY_XILINX_GMII2RGMII
+ bool "Xilinx GMII to RGMII Ethernet PHYs support"
+ help
+ This adds support for Xilinx GMII to RGMII IP core. This IP acts
+ as bridge between MAC connected over GMII and external phy that
+ is connected over RGMII interface.
+
config PHY_FIXED
bool "Fixed-Link PHY"
depends on DM_ETH
on, the link is always up with fixed speed and fixed duplex-setting.
More information: doc/device-tree-bindings/net/fixed-link.txt
+config PHY_NCSI
+ bool "NC-SI based PHY"
+ depends on DM_ETH
+
endif #PHYLIB
projects / platform / kernel / u-boot.git / blobdiff