Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians...

[platform/kernel/u-boot.git] / drivers / net / phy / Kconfig

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 2a3da06..51733dd 100644 (file)
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -46,7 +46,7 @@ config B53_PHY_PORTS
 endif # B53_SWITCH
 
 config MV88E61XX_SWITCH
-       bool "Marvel MV88E61xx Ethernet switch PHY support."
+       bool "Marvell MV88E61xx Ethernet switch PHY support."
 
 if MV88E61XX_SWITCH
 
@@ -100,6 +100,37 @@ config PHY_BROADCOM
 config PHY_CORTINA
        bool "Cortina Ethernet PHYs support"
 
+config SYS_CORTINA_NO_FW_UPLOAD
+       bool "Cortina firmware loading support"
+       default n
+       depends on PHY_CORTINA
+       help
+               Cortina phy has provision to store phy firmware in attached dedicated
+               EEPROM. And boards designed with such EEPROM does not require firmware
+               upload.
+
+choice
+       prompt "Location of the Cortina firmware"
+       default SYS_CORTINA_FW_IN_NOR
+       depends on PHY_CORTINA
+
+config SYS_CORTINA_FW_IN_MMC
+       bool "Cortina firmware in MMC"
+
+config SYS_CORTINA_FW_IN_NAND
+       bool "Cortina firmware in NAND flash"
+
+config SYS_CORTINA_FW_IN_NOR
+       bool "Cortina firmware in NOR flash"
+
+config SYS_CORTINA_FW_IN_REMOTE
+       bool "Cortina firmware in remote device"
+
+config SYS_CORTINA_FW_IN_SPIFLASH
+       bool "Cortina firmware in SPI flash"
+
+endchoice
+
 config PHY_DAVICOM
        bool "Davicom Ethernet PHYs support"
 
@@ -213,6 +244,15 @@ config RTL8211F_PHY_FORCE_EEE_RXC_ON
          Default n, which means that the PHY state is not changed. To work
          around the issues, change this setting to y.
 
+config RTL8201F_PHY_S700_RMII_TIMINGS
+       bool "Ethernet PHY RTL8201F: adjust RMII Tx Interface timings"
+       depends on PHY_REALTEK
+       help
+         This provides an option to configure specific timing requirements (needed
+         for proper PHY operations) for the PHY module present on ACTION SEMI S700
+         based cubieboard7. Exact timing requiremnets seems to be SoC specific
+         (and it's undocumented) that comes from vendor code itself.
+
 config PHY_SMSC
        bool  "Microchip(SMSC) Ethernet PHYs support"
 
@@ -221,6 +261,21 @@ config PHY_TERANETICS
 
 config PHY_TI
        bool "Texas Instruments Ethernet PHYs support"
+       ---help---
+         Adds PHY registration support for TI PHYs.
+
+config PHY_TI_DP83867
+       select PHY_TI
+       bool "Texas Instruments Ethernet DP83867 PHY support"
+       ---help---
+         Adds support for the TI DP83867 1Gbit PHY.
+
+config PHY_TI_GENERIC
+       select PHY_TI
+       bool "Texas Instruments Generic Ethernet PHYs support"
+       ---help---
+         Adds support for Generic TI PHYs that don't need special handling but
+         the PHY name is associated with a PHY ID.
 
 config PHY_VITESSE
        bool "Vitesse Ethernet PHYs support"
@@ -228,6 +283,13 @@ config PHY_VITESSE
 config PHY_XILINX
        bool "Xilinx Ethernet PHYs support"
 
+config PHY_XILINX_GMII2RGMII
+       bool "Xilinx GMII to RGMII Ethernet PHYs support"
+       help
+         This adds support for Xilinx GMII to RGMII IP core. This IP acts
+         as bridge between MAC connected over GMII and external phy that
+         is connected over RGMII interface.
+
 config PHY_FIXED
        bool "Fixed-Link PHY"
        depends on DM_ETH
@@ -238,4 +300,8 @@ config PHY_FIXED
          on, the link is always up with fixed speed and fixed duplex-setting.
          More information: doc/device-tree-bindings/net/fixed-link.txt
 
+config PHY_NCSI
+       bool "NC-SI based PHY"
+       depends on DM_ETH
+
 endif #PHYLIB