const unsigned char *buf, int start_page);
static int wd_close(struct net_device *dev);
+static u32 wd_msg_enable;
#define WD_START_PG 0x00 /* First page of TX buffer */
#define WD03_STOP_PG 0x20 /* Last page +1 of RX ring */
int word16 = 0; /* 0 = 8 bit, 1 = 16 bit */
const char *model_name;
static unsigned version_printed;
+ struct ei_device *ei_local = netdev_priv(dev);
for (i = 0; i < 8; i++)
checksum += inb(ioaddr + 8 + i);
/* Check for semi-valid mem_start/end values if supplied. */
if ((dev->mem_start % 0x2000) || (dev->mem_end % 0x2000)) {
- printk(KERN_WARNING "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n");
+ netdev_warn(dev,
+ "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n");
dev->mem_start = 0;
dev->mem_end = 0;
}
- if (ei_debug && version_printed++ == 0)
- printk(version);
+ if ((wd_msg_enable & NETIF_MSG_DRV) && (version_printed++ == 0))
+ netdev_info(dev, version);
for (i = 0; i < 6; i++)
dev->dev_addr[i] = inb(ioaddr + 8 + i);
- printk("%s: WD80x3 at %#3x, %pM",
- dev->name, ioaddr, dev->dev_addr);
+ netdev_info(dev, "WD80x3 at %#3x, %pM", ioaddr, dev->dev_addr);
/* The following PureData probe code was contributed by
Mike Jagdis <jaggy@purplet.demon.co.uk>. Puredata does software
}
#ifndef final_version
if ( !ancient && (inb(ioaddr+1) & 0x01) != (word16 & 0x01))
- printk("\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).",
- word16 ? 16 : 8, (inb(ioaddr+1) & 0x01) ? 16 : 8);
+ pr_cont("\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).",
+ word16 ? 16 : 8,
+ (inb(ioaddr+1) & 0x01) ? 16 : 8);
#endif
}
if (reg0 == 0xff || reg0 == 0) {
/* Future plan: this could check a few likely locations first. */
dev->mem_start = 0xd0000;
- printk(" assigning address %#lx", dev->mem_start);
+ pr_cont(" assigning address %#lx", dev->mem_start);
} else {
int high_addr_bits = inb(ioaddr+WD_CMDREG5) & 0x1f;
/* Some boards don't have the register 5 -- it returns 0xff. */
outb_p(0x00, nic_addr+EN0_IMR); /* Mask all intrs. again. */
- if (ei_debug > 2)
- printk(" autoirq is %d", dev->irq);
+ if (netif_msg_drv(ei_local))
+ pr_cont(" autoirq is %d", dev->irq);
if (dev->irq < 2)
dev->irq = word16 ? 10 : 5;
} else
share and the board will usually be enabled. */
i = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev);
if (i) {
- printk (" unable to get IRQ %d.\n", dev->irq);
+ pr_cont(" unable to get IRQ %d.\n", dev->irq);
return i;
}
return -ENOMEM;
}
- printk(" %s, IRQ %d, shared memory at %#lx-%#lx.\n",
- model_name, dev->irq, dev->mem_start, dev->mem_end-1);
+ pr_cont(" %s, IRQ %d, shared memory at %#lx-%#lx.\n",
+ model_name, dev->irq, dev->mem_start, dev->mem_end-1);
ei_status.reset_8390 = wd_reset_8390;
ei_status.block_input = wd_block_input;
dev->netdev_ops = &wd_netdev_ops;
NS8390_init(dev, 0);
+ ei_local->msg_enable = wd_msg_enable;
#if 1
/* Enable interrupt generation on softconfig cards -- M.U */
wd_reset_8390(struct net_device *dev)
{
int wd_cmd_port = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */
+ struct ei_device *ei_local = netdev_priv(dev);
outb(WD_RESET, wd_cmd_port);
- if (ei_debug > 1) printk("resetting the WD80x3 t=%lu...", jiffies);
+ netif_dbg(ei_local, hw, dev, "resetting the WD80x3 t=%lu...\n",
+ jiffies);
ei_status.txing = 0;
/* Set up the ASIC registers, just in case something changed them. */
if (ei_status.word16)
outb(NIC16 | ((dev->mem_start>>19) & 0x1f), wd_cmd_port+WD_CMDREG5);
- if (ei_debug > 1) printk("reset done\n");
+ netif_dbg(ei_local, hw, dev, "reset done\n");
}
/* Grab the 8390 specific header. Similar to the block_input routine, but
wd_close(struct net_device *dev)
{
int wd_cmdreg = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */
+ struct ei_device *ei_local = netdev_priv(dev);
- if (ei_debug > 1)
- printk("%s: Shutting down ethercard.\n", dev->name);
+ netif_dbg(ei_local, ifdown, dev, "Shutting down ethercard.\n");
ei_close(dev);
/* Change from 16-bit to 8-bit shared memory so reboot works. */
module_param_array(irq, int, NULL, 0);
module_param_array(mem, int, NULL, 0);
module_param_array(mem_end, int, NULL, 0);
+module_param_named(msg_enable, wd_msg_enable, uint, (S_IRUSR|S_IRGRP|S_IROTH));
MODULE_PARM_DESC(io, "I/O base address(es)");
MODULE_PARM_DESC(irq, "IRQ number(s) (ignored for PureData boards)");
MODULE_PARM_DESC(mem, "memory base address(es)(ignored for PureData boards)");
MODULE_PARM_DESC(mem_end, "memory end address(es)");
+MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
MODULE_DESCRIPTION("ISA Western Digital wd8003/wd8013 ; SMC Elite, Elite16 ethernet driver");
MODULE_LICENSE("GPL");
projects / platform / adaptation / renesas_rcar / renesas_kernel.git / blobdiff