This is currently implemented in net/eth-uclass.c
Look in include/net.h for details.
-config DRIVER_TI_CPSW
- bool "TI Common Platform Ethernet Switch"
- select PHYLIB
- help
- This driver supports the TI three port switch gigabit ethernet
- subsystem found in the TI SoCs.
-
menuconfig NETDEVICES
bool "Network device support"
depends on NET
by the BCM_SF2_ETH driver.
Say Y to any bcmcygnus based platforms.
+config BCM6348_ETH
+ bool "BCM6348 EMAC support"
+ depends on DM_ETH && ARCH_BMIPS
+ select DMA
+ select DMA_CHANNELS
+ select MII
+ select PHYLIB
+ help
+ This driver supports the BCM6348 Ethernet MAC.
+
+config BCM6368_ETH
+ bool "BCM6368 EMAC support"
+ depends on DM_ETH && ARCH_BMIPS
+ select DMA
+ select MII
+ help
+ This driver supports the BCM6368 Ethernet MAC.
+
config DWC_ETH_QOS
bool "Synopsys DWC Ethernet QOS device support"
depends on DM_ETH
config ETH_DESIGNWARE
bool "Synopsys Designware Ethernet MAC"
select PHYLIB
+ imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
help
This MAC is present in SoCs from various vendors. It supports
100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
provide the PHY (physical media interface).
+config ETH_DESIGNWARE_SOCFPGA
+ select REGMAP
+ select SYSCON
+ bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
+ depends on DM_ETH && ETH_DESIGNWARE
+ help
+ The Altera SoCFPGA requires additional configuration of the
+ Altera system manager to correctly interface with the PHY.
+ This code handles those SoC specifics.
+
config ETHOC
bool "OpenCores 10/100 Mbps Ethernet MAC"
help
config FEC_MXC
bool "FEC Ethernet controller"
- depends on MX5 || MX6 || MX7
+ depends on MX5 || MX6 || MX7 || IMX8 || VF610
help
This driver supports the 10/100 Fast Ethernet controller for
NXP i.MX processors.
+config FMAN_ENET
+ bool "Freescale FMan ethernet support"
+ depends on ARM || PPC
+ help
+ This driver support the Freescale FMan Ethernet controller
+
config FTMAC100
bool "Ftmac100 Ethernet Support"
help
This MAC is present in Andestech SoCs.
+config FTGMAC100
+ bool "Ftgmac100 Ethernet Support"
+ depends on DM_ETH
+ select PHYLIB
+ help
+ This driver supports the Faraday's FTGMAC100 Gigabit SoC
+ Ethernet controller that can be found on Aspeed SoCs (which
+ include NCSI).
+
+ It is fully compliant with IEEE 802.3 specification for
+ 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
+ Mbps Ethernet and includes Reduced Media Independent
+ Interface (RMII) and Reduced Gigabit Media Independent
+ Interface (RGMII) interfaces. It adopts an AHB bus interface
+ and integrates a link list DMA engine with direct M-Bus
+ accesses for transmitting and receiving packets. It has
+ independent TX/RX fifos, supports half and full duplex (1000
+ Mbps mode only supports full duplex), flow control for full
+ duplex and backpressure for half duplex.
+
+ The FTGMAC100 also implements IP, TCP, UDP checksum offloads
+ and supports IEEE 802.1Q VLAN tag insertion and removal. It
+ offers high-priority transmit queue for QoS and CoS
+ applications.
+
+
config MVGBE
bool "Marvell Orion5x/Kirkwood network interface support"
depends on KIRKWOOD || ORION5X
The Cadence MACB ethernet interface was used on Zynq platform.
Say Y to enable support for the MACB/GEM in Zynq chip.
+config MT7628_ETH
+ bool "MediaTek MT7628 Ethernet Interface"
+ depends on SOC_MT7628
+ help
+ The MediaTek MT7628 ethernet interface is used on MT7628 and
+ MT7688 based boards.
+
config PCH_GBE
bool "Intel Platform Controller Hub EG20T GMAC driver"
depends on DM_ETH && DM_PCI
Enable the support of the Reduced Gigabit Media-Independent
Interface (RGMII).
+config MII
+ bool "Enable MII"
+ help
+ Enable support of the Media-Independent Interface (MII)
+
config RTL8139
bool "Realtek 8139 series Ethernet controller driver"
help
help
This driver supports the Ethernet for Renesas SH and ARM SoCs.
+source "drivers/net/ti/Kconfig"
+
config XILINX_AXIEMAC
depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
select PHYLIB
This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
config ZYNQ_GEM
- depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
+ depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL)
select PHYLIB
bool "Xilinx Ethernet GEM"
help
This driver implements support for the Socionext AVE Ethernet
controller, as found on the Socionext UniPhier family.
+source "drivers/net/mscc_eswitch/Kconfig"
+
config ETHER_ON_FEC1
bool "FEC1"
depends on MPC8XX_FEC
This driver implements support for the (Enhanced) Three-Speed
Ethernet Controller found on Freescale SoCs.
+config MEDIATEK_ETH
+ bool "MediaTek Ethernet GMAC Driver"
+ depends on DM_ETH
+ select PHYLIB
+ select DM_GPIO
+ select DM_RESET
+ help
+ This Driver support MediaTek Ethernet GMAC
+ Say Y to enable support for the MediaTek Ethernet GMAC.
+
+config HIGMACV300_ETH
+ bool "HiSilicon Gigabit Ethernet Controller"
+ depends on DM_ETH
+ select DM_RESET
+ select PHYLIB
+ help
+ This driver supports HIGMACV300 Ethernet controller found on
+ HiSilicon SoCs.
+
endif # NETDEVICES
projects / platform / kernel / u-boot.git / blobdiff