source "drivers/net/phy/Kconfig"
source "drivers/net/pfe_eth/Kconfig"
source "drivers/net/fsl-mc/Kconfig"
+source "drivers/net/bnxt/Kconfig"
+
+config ETH
+ def_bool y
config DM_ETH
bool "Enable Driver Model for Ethernet drivers"
help
Enable driver model for Ethernet Generic PHY .
+config DSA_SANDBOX
+ depends on DM_DSA && SANDBOX
+ default y
+ bool "Sandbox: Mocked DSA driver"
+ help
+ This driver implements a dummy DSA switch connected to a dummy sandbox
+ Ethernet device used as DSA master, to test DSA class code, including
+ exported DSA API and datapath processing of Ethernet traffic.
+
menuconfig NETDEVICES
bool "Network device support"
depends on NET
This driver supports the Cortina-Access Ethernet MAC for
all supported CAxxxx SoCs.
+config CALXEDA_XGMAC
+ bool "Calxeda XGMAC support"
+ depends on DM_ETH
+ help
+ This driver supports the XGMAC in Calxeda Highbank and Midway
+ machines.
+
+config DRIVER_DM9000
+ bool "Davicom DM9000 controller driver"
+ help
+ The Davicom DM9000 parallel bus external ethernet interface chip.
+
config DWC_ETH_QOS
bool "Synopsys DWC Ethernet QOS device support"
depends on DM_ETH
config DWC_ETH_QOS_STM32
bool "Synopsys DWC Ethernet QOS device support for STM32"
depends on DWC_ETH_QOS
+ select DM_ETH_PHY
default y if ARCH_STM32MP
help
The Synopsys Designware Ethernet QOS IP block with the specific
config E1000
bool "Intel PRO/1000 Gigabit Ethernet support"
- depends on (DM_ETH && DM_PCI) || !DM_ETH
+ depends on PCI
help
This driver supports Intel(R) PRO/1000 gigabit ethernet family of
adapters. For more information on how to identify your adapter, go
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
+config E1000_NO_NVM
+ bool "Intel PRO/1000 has no NVMEM / EEPROM"
+ depends on E1000
+
config E1000_SPI_GENERIC
bool "Allow access to the Intel 8257x SPI bus"
depends on E1000
config ETH_DESIGNWARE_SOCFPGA
select REGMAP
select SYSCON
+ select DW_ALTDESCRIPTOR
bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
depends on DM_ETH && ETH_DESIGNWARE
help
This provides glue layer to use Synopsys Designware Ethernet MAC
present on Actions S700 SoC.
+config DW_ALTDESCRIPTOR
+ bool "Designware Ethernet MAC uses alternate (enhanced) descriptors"
+ depends on ETH_DESIGNWARE
+
config ETHOC
bool "OpenCores 10/100 Mbps Ethernet MAC"
help
config FEC_MXC
bool "FEC Ethernet controller"
- depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
+ depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || IMX8ULP || IMX93 || VF610
help
This driver supports the 10/100 Fast Ethernet controller for
NXP i.MX processors.
config FMAN_ENET
bool "Freescale FMan ethernet support"
depends on ARM || PPC
+ select SYS_FMAN_V3 if ARCH_B4420 || ARCH_B4860 || ARCH_LS1043A || \
+ ARCH_LS1046A || ARCH_T1024 || ARCH_T1040 || ARCH_T1042 || \
+ ARCH_T2080 || ARCH_T4240
help
This driver support the Freescale FMan Ethernet controller
+config SYS_FMAN_FW_ADDR
+ hex "FMAN Firmware Address"
+ depends on FMAN_ENET
+ default 0x0
+
+config SYS_QE_FMAN_FW_LENGTH
+ hex "FMAN QE Firmware length"
+ depends on FMAN_ENET || QE || U_QE
+ default 0x10000
+
+config SYS_FMAN_V3
+ bool
+ select FSL_MEMAC
+ help
+ SoC has FMan v3 with mEMAC
+
config FTMAC100
bool "Ftmac100 Ethernet Support"
help
offers high-priority transmit queue for QoS and CoS
applications.
+config SYS_DISCOVER_PHY
+ bool
config MCFFEC
bool "ColdFire Ethernet Support"
depends on DM_ETH
select PHYLIB
+ select SYS_DISCOVER_PHY
help
This driver supports the network interface units in the
ColdFire family.
+config SYS_UNIFY_CACHE
+ depends on MCFFEC
+ bool "Invalidate icache during ethernet operations"
+
config FSLDMAFEC
bool "ColdFire DMA Ethernet Support"
depends on DM_ETH
select PHYLIB
+ select SYS_DISCOVER_PHY
help
This driver supports the network interface units in the
ColdFire family.
endif #DM_ETH
endif #KS8851_MLL
+config KSZ9477
+ bool "Microchip KSZ9477 I2C controller driver"
+ depends on DM_DSA && DM_I2C
+ help
+ This driver implements a DSA switch driver for the KSZ9477 family
+ of GbE switches using the I2C interface.
+
+config LPC32XX_ETH
+ bool "LPC32xx Ethernet MAC interface driver"
+ depends on ARCH_LPC32XX
+ default y
+
config MVGBE
bool "Marvell Orion5x/Kirkwood network interface support"
depends on ARCH_KIRKWOOD || ARCH_ORION5X
bool "Marvell Armada XP/385/3700 network interface support"
depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
select PHYLIB
+ select DM_MDIO
help
This driver supports the network interface units in the
Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
config MACB
bool "Cadence MACB/GEM Ethernet Interface"
- depends on DM_ETH
select PHYLIB
help
The Cadence MACB ethernet interface is found on many Atmel
The MediaTek MT7628 ethernet interface is used on MT7628 and
MT7688 based boards.
+config NET_OCTEON
+ bool "MIPS Octeon ethernet support"
+ depends on ARCH_OCTEON
+ help
+ You must select Y to enable network device support for
+ MIPS Octeon SoCs. If unsure, say n
+
config NET_OCTEONTX
bool "OcteonTX Ethernet support"
depends on ARCH_OCTEONTX
config PCH_GBE
bool "Intel Platform Controller Hub EG20T GMAC driver"
- depends on DM_ETH && DM_PCI
+ depends on DM_ETH
select PHYLIB
help
This MAC is present in Intel Platform Controller Hub EG20T. It
help
Enable support of the Media-Independent Interface (MII)
+config RMII
+ bool "Enable RMII"
+ help
+ Enable support of the Reduced Media-Independent Interface (MII)
+
config PCNET
bool "AMD PCnet series Ethernet controller driver"
help
This driver supports Realtek 8169 series gigabit ethernet family of
PCI/PCIe chipsets/adapters.
+config SJA1105
+ bool "NXP SJA1105 Ethernet switch family driver"
+ depends on DM_DSA && DM_SPI
+ select BITREVERSE
+ help
+ This is the driver for the NXP SJA1105 automotive Ethernet switch
+ family. These are 5-port devices and are managed over an SPI
+ interface. Probing is handled based on OF bindings. The driver
+ supports the following revisions:
+ - SJA1105E (Gen. 1, No TT-Ethernet)
+ - SJA1105T (Gen. 1, TT-Ethernet)
+ - SJA1105P (Gen. 2, No SGMII, No TT-Ethernet)
+ - SJA1105Q (Gen. 2, No SGMII, TT-Ethernet)
+ - SJA1105R (Gen. 2, SGMII, No TT-Ethernet)
+ - SJA1105S (Gen. 2, SGMII, TT-Ethernet)
+
config SMC911X
bool "SMSC LAN911x and LAN921x controller driver"
of the device (I/O space)
endif #DM_ETH
-choice
- prompt "SMC911X bus width"
- default SMC911X_16_BIT
-
config SMC911X_32_BIT
- bool "Enable 32-bit interface"
-
-config SMC911X_16_BIT
- bool "Enable 16-bit interface"
+ bool "Enable SMC911X 32-bit interface"
help
- Define this if data bus is 16 bits. If your processor
- automatically converts one 32 bit word to two 16 bit
- words you may also try CONFIG_SMC911X_32_BIT.
+ Define this if data bus is 32 bits. If your processor use a
+ narrower 16 bit bus or cannot convert one 32 bit word to two 16 bit
+ words, leave this to "n".
-endchoice
endif #SMC911X
config SUN7I_GMAC
config TULIP
bool "DEC Tulip DC2114x Ethernet support"
- depends on (DM_ETH && DM_PCI) || !DM_ETH
help
This driver supports DEC DC2114x Fast ethernet chips.
help
This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
+config XILINX_AXIMRMAC
+ depends on DM_ETH && ARCH_VERSAL
+ bool "Xilinx AXI MRMAC"
+ help
+ MRMAC is a high performance, low latency, adaptable Ethernet
+ integrated hard IP. This can be configured up to four ports with MAC
+ rates from 10GE to 100GE. This could be present in some of the Xilinx
+ Versal designs.
+
config XILINX_EMACLITE
depends on DM_ETH
select PHYLIB
bool "Fast Ethernet Controller on MPC8XX"
depends on MPC8xx
select MII
+ select SYS_DISCOVER_PHY
help
This driver implements support for the Fast Ethernet Controller
on MPC8XX
This driver implements support for the Socionext AVE Ethernet
controller, as found on the Socionext UniPhier family.
+config SNI_NETSEC
+ bool "Socionext NETSEC Ethernet support"
+ depends on DM_ETH && SYNQUACER_SPI
+ select PHYLIB
+ help
+ This driver implements support for the Socionext SynQuacer NETSEC
+ ethernet controller, as found on the Socionext SynQuacer family.
+
source "drivers/net/mscc_eswitch/Kconfig"
config ETHER_ON_FEC1
config PHY_NORXERR
bool "PHY_NORXERR"
depends on ETHER_ON_FEC1
- default n
help
The PHY does not have a RXERR line (RMII only).
(so program the FEC to ignore it).
config FEC2_PHY_NORXERR
bool "PHY_NORXERR"
depends on ETHER_ON_FEC2
- default n
help
The PHY does not have a RXERR line (RMII only).
(so program the FEC to ignore it).
ARCH_B4420 || \
ARCH_P1023 || \
ARCH_P2041 || \
- ARCH_T1023 || \
ARCH_T1024 || \
ARCH_T1040 || \
ARCH_T1042 || \
ARCH_T2080 || \
ARCH_T4240 || \
- ARCH_T4160 || \
ARCH_P4080 || \
ARCH_P3041 || \
ARCH_P5040 || \
config FSL_ENETC
bool "NXP ENETC Ethernet controller"
- depends on DM_PCI && DM_ETH && DM_MDIO
+ depends on DM_ETH && DM_MDIO
help
This driver supports the NXP ENETC Ethernet controller found on some
of the NXP SoCs.
This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
on the mEMAC (which supports both Clauses 22 and 45).
+config ASPEED_MDIO
+ bool "Aspeed MDIO interface support"
+ depends on DM_MDIO
+ help
+ This driver supports the MDIO bus of Aspeed AST2600 SOC. The driver
+ currently supports Clause 22.
+
config MDIO_MUX_MMIOREG
bool "MDIO MUX accessed as a MMIO register access"
depends on DM_MDIO_MUX
projects / platform / kernel / u-boot.git / blobdiff