*/
#include <common.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/log2.h>
#include <spi-mem.h>
#include <spi.h>
+#include "sf_internal.h"
+
/* Define max times to check status register before we give up. */
/*
#define DEFAULT_READY_WAIT_JIFFIES (40UL * HZ)
-#define SPI_NOR_MAX_ID_LEN 6
-#define SPI_NOR_MAX_ADDR_WIDTH 4
-
-struct flash_info {
- char *name;
-
- /*
- * This array stores the ID bytes.
- * The first three bytes are the JEDIC ID.
- * JEDEC ID zero means "no ID" (mostly older chips).
- */
- u8 id[SPI_NOR_MAX_ID_LEN];
- u8 id_len;
-
- /* The size listed here is what works with SPINOR_OP_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
- unsigned int sector_size;
- u16 n_sectors;
-
- u16 page_size;
- u16 addr_width;
-
- u16 flags;
-#define SECT_4K BIT(0) /* SPINOR_OP_BE_4K works uniformly */
-#define SPI_NOR_NO_ERASE BIT(1) /* No erase command needed */
-#define SST_WRITE BIT(2) /* use SST byte programming */
-#define SPI_NOR_NO_FR BIT(3) /* Can't do fastread */
-#define SECT_4K_PMC BIT(4) /* SPINOR_OP_BE_4K_PMC works uniformly */
-#define SPI_NOR_DUAL_READ BIT(5) /* Flash supports Dual Read */
-#define SPI_NOR_QUAD_READ BIT(6) /* Flash supports Quad Read */
-#define USE_FSR BIT(7) /* use flag status register */
-#define SPI_NOR_HAS_LOCK BIT(8) /* Flash supports lock/unlock via SR */
-#define SPI_NOR_HAS_TB BIT(9) /*
- * Flash SR has Top/Bottom (TB) protect
- * bit. Must be used with
- * SPI_NOR_HAS_LOCK.
- */
-#define SPI_S3AN BIT(10) /*
- * Xilinx Spartan 3AN In-System Flash
- * (MFR cannot be used for probing
- * because it has the same value as
- * ATMEL flashes)
- */
-#define SPI_NOR_4B_OPCODES BIT(11) /*
- * Use dedicated 4byte address op codes
- * to support memory size above 128Mib.
- */
-#define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */
-#define USE_CLSR BIT(14) /* use CLSR command */
-
- int (*quad_enable)(struct spi_nor *nor);
-};
-
-#define JEDEC_MFR(info) ((info)->id[0])
+static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
+ *op, void *buf)
+{
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ op->data.buf.in = buf;
+ else
+ op->data.buf.out = buf;
+ return spi_mem_exec_op(nor->spi, op);
+}
static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
{
- return -EINVAL;
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_IN(len, NULL, 1));
+ int ret;
+
+ ret = spi_nor_read_write_reg(nor, &op, val);
+ if (ret < 0)
+ dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
+ code);
+
+ return ret;
}
static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
{
- return -EINVAL;
+ struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
+ SPI_MEM_OP_NO_ADDR,
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, NULL, 1));
+
+ return spi_nor_read_write_reg(nor, &op, buf);
}
static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
u_char *buf)
{
- return -EINVAL;
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
+ SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
+ SPI_MEM_OP_DATA_IN(len, buf, 1));
+ size_t remaining = len;
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
+ op.dummy.buswidth = op.addr.buswidth;
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
+
+ /* convert the dummy cycles to the number of bytes */
+ op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
+
+ while (remaining) {
+ op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ op.addr.val += op.data.nbytes;
+ remaining -= op.data.nbytes;
+ op.data.buf.in += op.data.nbytes;
+ }
+
+ return len;
}
static ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
const u_char *buf)
{
- return -EINVAL;
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(len, buf, 1));
+ int ret;
+
+ /* get transfer protocols. */
+ op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
+ op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
+ op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
+
+ if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
+ op.addr.nbytes = 0;
+
+ ret = spi_mem_adjust_op_size(nor->spi, &op);
+ if (ret)
+ return ret;
+ op.data.nbytes = len < op.data.nbytes ? len : op.data.nbytes;
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ return op.data.nbytes;
}
/*
return mtd->priv;
}
+#ifndef CONFIG_SPI_FLASH_BAR
+static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == opcode)
+ return table[i][1];
+
+ /* No conversion found, keep input op code. */
+ return opcode;
+}
+
+static u8 spi_nor_convert_3to4_read(u8 opcode)
+{
+ static const u8 spi_nor_3to4_read[][2] = {
+ { SPINOR_OP_READ, SPINOR_OP_READ_4B },
+ { SPINOR_OP_READ_FAST, SPINOR_OP_READ_FAST_4B },
+ { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
+ { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
+ { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
+ { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
+ { SPINOR_OP_READ_1_1_8, SPINOR_OP_READ_1_1_8_4B },
+ { SPINOR_OP_READ_1_8_8, SPINOR_OP_READ_1_8_8_4B },
+
+ { SPINOR_OP_READ_1_1_1_DTR, SPINOR_OP_READ_1_1_1_DTR_4B },
+ { SPINOR_OP_READ_1_2_2_DTR, SPINOR_OP_READ_1_2_2_DTR_4B },
+ { SPINOR_OP_READ_1_4_4_DTR, SPINOR_OP_READ_1_4_4_DTR_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
+ ARRAY_SIZE(spi_nor_3to4_read));
+}
+
+static u8 spi_nor_convert_3to4_program(u8 opcode)
+{
+ static const u8 spi_nor_3to4_program[][2] = {
+ { SPINOR_OP_PP, SPINOR_OP_PP_4B },
+ { SPINOR_OP_PP_1_1_4, SPINOR_OP_PP_1_1_4_4B },
+ { SPINOR_OP_PP_1_4_4, SPINOR_OP_PP_1_4_4_4B },
+ { SPINOR_OP_PP_1_1_8, SPINOR_OP_PP_1_1_8_4B },
+ { SPINOR_OP_PP_1_8_8, SPINOR_OP_PP_1_8_8_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_program,
+ ARRAY_SIZE(spi_nor_3to4_program));
+}
+
+static u8 spi_nor_convert_3to4_erase(u8 opcode)
+{
+ static const u8 spi_nor_3to4_erase[][2] = {
+ { SPINOR_OP_BE_4K, SPINOR_OP_BE_4K_4B },
+ { SPINOR_OP_BE_32K, SPINOR_OP_BE_32K_4B },
+ { SPINOR_OP_SE, SPINOR_OP_SE_4B },
+ };
+
+ return spi_nor_convert_opcode(opcode, spi_nor_3to4_erase,
+ ARRAY_SIZE(spi_nor_3to4_erase));
+}
+
+static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
+ const struct flash_info *info)
+{
+ /* Do some manufacturer fixups first */
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_SPANSION:
+ /* No small sector erase for 4-byte command set */
+ nor->erase_opcode = SPINOR_OP_SE;
+ nor->mtd.erasesize = info->sector_size;
+ break;
+
+ default:
+ break;
+ }
+
+ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
+ nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
+ nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
+}
+#endif /* !CONFIG_SPI_FLASH_BAR */
+
+/* Enable/disable 4-byte addressing mode. */
+static int set_4byte(struct spi_nor *nor, const struct flash_info *info,
+ int enable)
+{
+ int status;
+ bool need_wren = false;
+ u8 cmd;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_ST:
+ case SNOR_MFR_MICRON:
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case SNOR_MFR_ISSI:
+ case SNOR_MFR_MACRONIX:
+ case SNOR_MFR_WINBOND:
+ if (need_wren)
+ write_enable(nor);
+
+ cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
+ status = nor->write_reg(nor, cmd, NULL, 0);
+ if (need_wren)
+ write_disable(nor);
+
+ if (!status && !enable &&
+ JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
+ /*
+ * On Winbond W25Q256FV, leaving 4byte mode causes
+ * the Extended Address Register to be set to 1, so all
+ * 3-byte-address reads come from the second 16M.
+ * We must clear the register to enable normal behavior.
+ */
+ write_enable(nor);
+ nor->cmd_buf[0] = 0;
+ nor->write_reg(nor, SPINOR_OP_WREAR, nor->cmd_buf, 1);
+ write_disable(nor);
+ }
+
+ return status;
+ default:
+ /* Spansion style */
+ nor->cmd_buf[0] = enable << 7;
+ return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
+ }
+}
+
static int spi_nor_sr_ready(struct spi_nor *nor)
{
int sr = read_sr(nor);
if (fsr & (FSR_E_ERR | FSR_P_ERR)) {
if (fsr & FSR_E_ERR)
- dev_dbg(nor->dev, "Erase operation failed.\n");
+ dev_err(nor->dev, "Erase operation failed.\n");
else
- dev_dbg(nor->dev, "Program operation failed.\n");
+ dev_err(nor->dev, "Program operation failed.\n");
if (fsr & FSR_PT_ERR)
- dev_dbg(nor->dev,
+ dev_err(nor->dev,
"Attempted to modify a protected sector.\n");
nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0);
DEFAULT_READY_WAIT_JIFFIES);
}
+#ifdef CONFIG_SPI_FLASH_BAR
+/*
+ * This "clean_bar" is necessary in a situation when one was accessing
+ * spi flash memory > 16 MiB by using Bank Address Register's BA24 bit.
+ *
+ * After it the BA24 bit shall be cleared to allow access to correct
+ * memory region after SW reset (by calling "reset" command).
+ *
+ * Otherwise, the BA24 bit may be left set and then after reset, the
+ * ROM would read/write/erase SPL from 16 MiB * bank_sel address.
+ */
+static int clean_bar(struct spi_nor *nor)
+{
+ u8 cmd, bank_sel = 0;
+
+ if (nor->bank_curr == 0)
+ return 0;
+ cmd = nor->bank_write_cmd;
+ nor->bank_curr = 0;
+ write_enable(nor);
+
+ return nor->write_reg(nor, cmd, &bank_sel, 1);
+}
+
+static int write_bar(struct spi_nor *nor, u32 offset)
+{
+ u8 cmd, bank_sel;
+ int ret;
+
+ bank_sel = offset / SZ_16M;
+ if (bank_sel == nor->bank_curr)
+ goto bar_end;
+
+ cmd = nor->bank_write_cmd;
+ write_enable(nor);
+ ret = nor->write_reg(nor, cmd, &bank_sel, 1);
+ if (ret < 0) {
+ debug("SF: fail to write bank register\n");
+ return ret;
+ }
+
+bar_end:
+ nor->bank_curr = bank_sel;
+ return nor->bank_curr;
+}
+
+static int read_bar(struct spi_nor *nor, const struct flash_info *info)
+{
+ u8 curr_bank = 0;
+ int ret;
+
+ switch (JEDEC_MFR(info)) {
+ case SNOR_MFR_SPANSION:
+ nor->bank_read_cmd = SPINOR_OP_BRRD;
+ nor->bank_write_cmd = SPINOR_OP_BRWR;
+ break;
+ default:
+ nor->bank_read_cmd = SPINOR_OP_RDEAR;
+ nor->bank_write_cmd = SPINOR_OP_WREAR;
+ }
+
+ ret = nor->read_reg(nor, nor->bank_read_cmd,
+ &curr_bank, 1);
+ if (ret) {
+ debug("SF: fail to read bank addr register\n");
+ return ret;
+ }
+ nor->bank_curr = curr_bank;
+
+ return 0;
+}
+#endif
+
/*
* Initiate the erasure of a single sector
*/
static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
{
- u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
- int i;
+ struct spi_mem_op op =
+ SPI_MEM_OP(SPI_MEM_OP_CMD(nor->erase_opcode, 1),
+ SPI_MEM_OP_ADDR(nor->addr_width, addr, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_NO_DATA);
if (nor->erase)
return nor->erase(nor, addr);
* Default implementation, if driver doesn't have a specialized HW
* control
*/
- for (i = nor->addr_width - 1; i >= 0; i--) {
- buf[i] = addr & 0xff;
- addr >>= 8;
- }
-
- return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width);
+ return spi_mem_exec_op(nor->spi, &op);
}
/*
dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
(long long)instr->len);
+ if (!instr->len)
+ return 0;
+
div_u64_rem(instr->len, mtd->erasesize, &rem);
if (rem)
return -EINVAL;
len = instr->len;
while (len) {
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return ret;
+#endif
write_enable(nor);
ret = spi_nor_erase_sector(nor, addr);
goto erase_err;
}
+erase_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
write_disable(nor);
-erase_err:
return ret;
}
}
#endif /* CONFIG_SPI_FLASH_STMICRO */
-/* Used when the "_ext_id" is two bytes at most */
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- .id = { \
- ((_jedec_id) >> 16) & 0xff, \
- ((_jedec_id) >> 8) & 0xff, \
- (_jedec_id) & 0xff, \
- ((_ext_id) >> 16) & 0xff, \
- ((_ext_id) >> 8) & 0xff, \
- (_ext_id) & 0xff, \
- }, \
- .id_len = 6, \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags),
-
-/* NOTE: double check command sets and memory organization when you add
- * more nor chips. This current list focusses on newer chips, which
- * have been converging on command sets which including JEDEC ID.
- *
- * All newly added entries should describe *hardware* and should use SECT_4K
- * (or SECT_4K_PMC) if hardware supports erasing 4 KiB sectors. For usage
- * scenarios excluding small sectors there is config option that can be
- * disabled: CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
- * For historical (and compatibility) reasons (before we got above config) some
- * old entries may be missing 4K flag.
- */
-const struct flash_info spi_nor_ids[] = {
-#ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */
- /* Atmel -- some are (confusingly) marketed as "DataFlash" */
- { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
- { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
-
- { "at45db011d", INFO(0x1f2200, 0, 64 * 1024, 4, SECT_4K) },
- { "at45db021d", INFO(0x1f2300, 0, 64 * 1024, 8, SECT_4K) },
- { "at45db041d", INFO(0x1f2400, 0, 64 * 1024, 8, SECT_4K) },
- { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
- { "at45db161d", INFO(0x1f2600, 0, 64 * 1024, 32, SECT_4K) },
- { "at45db321d", INFO(0x1f2700, 0, 64 * 1024, 64, SECT_4K) },
- { "at45db641d", INFO(0x1f2800, 0, 64 * 1024, 128, SECT_4K) },
- { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_EON /* EON */
- /* EON -- en25xxx */
- { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
- { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
- { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
- { "en25s64", INFO(0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_GIGADEVICE /* GIGADEVICE */
- /* GigaDevice */
- {
- "gd25q16", INFO(0xc84015, 0, 64 * 1024, 32,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25lq32", INFO(0xc86016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
-#endif
-#ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
- /* ISSI */
- { "is25lq040b", INFO(0x9d4013, 0, 64 * 1024, 8,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25lp032", INFO(0x9d6016, 0, 64 * 1024, 64, 0) },
- { "is25lp064", INFO(0x9d6017, 0, 64 * 1024, 128, 0) },
- { "is25lp128", INFO(0x9d6018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ) },
- { "is25lp256", INFO(0x9d6019, 0, 64 * 1024, 512,
- SECT_4K | SPI_NOR_DUAL_READ) },
- { "is25wp032", INFO(0x9d7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25wp064", INFO(0x9d7017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "is25wp128", INFO(0x9d7018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-#endif
-#ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
- /* Macronix */
- { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
- { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
- { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
- { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
- { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25u1635e", INFO(0xc22535, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
- { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
- { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
- { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
- { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
- { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { "mx66u51235f", INFO(0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { "mx66l1g45g", INFO(0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "mx25l1633e", INFO(0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
-#endif
-
-#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
- /* Micron */
- { "n25q016a", INFO(0x20bb15, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
- { "n25q032a", INFO(0x20bb16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q064a", INFO(0x20bb17, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "n25q256ax1", INFO(0x20bb19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
- { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
- { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
- { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
- { "n25q00a", INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
- { "mt25qu02g", INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
- /* Spansion/Cypress -- single (large) sector size only, at least
- * for the chips listed here (without boot sectors).
- */
- { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, USE_CLSR) },
- { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_256k", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_64k", INFO(0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl512s_512k", INFO(0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
- { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
- { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
- { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
- { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
- { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
- { "s25fl116k", INFO(0x014015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "s25fl164k", INFO(0x014017, 0, 64 * 1024, 128, SECT_4K) },
- { "s25fl208k", INFO(0x014014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ) },
- { "s25fl128l", INFO(0x016018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
-#endif
-#ifdef CONFIG_SPI_FLASH_SST /* SST */
- /* SST -- large erase sizes are "overlays", "sectors" are 4K */
- { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
- { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
- { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
- { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
- { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
- { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
- { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
- { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
- { "sst25wf020a", INFO(0x621612, 0, 64 * 1024, 4, SECT_4K) },
- { "sst25wf040b", INFO(0x621613, 0, 64 * 1024, 8, SECT_4K) },
- { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
- { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
- { "sst26vf064b", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "sst26wf016", INFO(0xbf2651, 0, 64 * 1024, 32, SECT_4K) },
- { "sst26wf032", INFO(0xbf2622, 0, 64 * 1024, 64, SECT_4K) },
- { "sst26wf064", INFO(0xbf2643, 0, 64 * 1024, 128, SECT_4K) },
-#endif
-#ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
- /* ST Microelectronics -- newer production may have feature updates */
- { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
- { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
- { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
- { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
- { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
- { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
- { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
- { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
- { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
- { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
-#endif
-#ifdef CONFIG_SPI_FLASH_WINBOND /* WINBOND */
- /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
- { "w25x05", INFO(0xef3010, 0, 64 * 1024, 1, SECT_4K) },
- { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
- { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
- { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
- {
- "w25q16dw", INFO(0xef6015, 0, 64 * 1024, 32,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q20cl", INFO(0xef4012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q20bw", INFO(0xef5012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q20ew", INFO(0xef6012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
- {
- "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "w25q32jv", INFO(0xef7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
- {
- "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
- "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
- { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
- SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
-#endif
-#ifdef CONFIG_SPI_FLASH_XMC
- /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
- { "XM25QH64A", INFO(0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { "XM25QH128A", INFO(0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-#endif
- { },
-};
-
static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
{
int tmp;
u8 id[SPI_NOR_MAX_ID_LEN];
const struct flash_info *info;
- if (!ARRAY_SIZE(spi_nor_ids))
- return ERR_PTR(-ENODEV);
-
tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
if (tmp < 0) {
dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
return ERR_PTR(tmp);
}
- for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
- info = &spi_nor_ids[tmp];
+ info = spi_nor_ids;
+ for (; info->name; info++) {
if (info->id_len) {
if (!memcmp(info->id, id, info->id_len))
- return &spi_nor_ids[tmp];
+ return info;
}
}
+
dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
id[0], id[1], id[2]);
return ERR_PTR(-ENODEV);
while (len) {
loff_t addr = from;
+ size_t read_len = len;
+
+#ifdef CONFIG_SPI_FLASH_BAR
+ u32 remain_len;
+
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return log_ret(ret);
+ remain_len = (SZ_16M * (nor->bank_curr + 1)) - addr;
+
+ if (len < remain_len)
+ read_len = len;
+ else
+ read_len = remain_len;
+#endif
- ret = nor->read(nor, addr, len, buf);
+ ret = nor->read(nor, addr, read_len, buf);
if (ret == 0) {
/* We shouldn't see 0-length reads */
ret = -EIO;
ret = 0;
read_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
return ret;
}
#ifdef CONFIG_SPI_FLASH_SST
-static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+/*
+ * sst26 flash series has its own block protection implementation:
+ * 4x - 8 KByte blocks - read & write protection bits - upper addresses
+ * 1x - 32 KByte blocks - write protection bits
+ * rest - 64 KByte blocks - write protection bits
+ * 1x - 32 KByte blocks - write protection bits
+ * 4x - 8 KByte blocks - read & write protection bits - lower addresses
+ *
+ * We'll support only per 64k lock/unlock so lower and upper 64 KByte region
+ * will be treated as single block.
+ */
+#define SST26_BPR_8K_NUM 4
+#define SST26_MAX_BPR_REG_LEN (18 + 1)
+#define SST26_BOUND_REG_SIZE ((32 + SST26_BPR_8K_NUM * 8) * SZ_1K)
+
+enum lock_ctl {
+ SST26_CTL_LOCK,
+ SST26_CTL_UNLOCK,
+ SST26_CTL_CHECK
+};
+
+static bool sst26_process_bpr(u32 bpr_size, u8 *cmd, u32 bit, enum lock_ctl ctl)
{
- struct spi_nor *nor = mtd_to_spi_nor(mtd);
- size_t actual;
+ switch (ctl) {
+ case SST26_CTL_LOCK:
+ cmd[bpr_size - (bit / 8) - 1] |= BIT(bit % 8);
+ break;
+ case SST26_CTL_UNLOCK:
+ cmd[bpr_size - (bit / 8) - 1] &= ~BIT(bit % 8);
+ break;
+ case SST26_CTL_CHECK:
+ return !!(cmd[bpr_size - (bit / 8) - 1] & BIT(bit % 8));
+ }
+
+ return false;
+}
+
+/*
+ * Lock, unlock or check lock status of the flash region of the flash (depending
+ * on the lock_ctl value)
+ */
+static int sst26_lock_ctl(struct spi_nor *nor, loff_t ofs, uint64_t len, enum lock_ctl ctl)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ u32 i, bpr_ptr, rptr_64k, lptr_64k, bpr_size;
+ bool lower_64k = false, upper_64k = false;
+ u8 bpr_buff[SST26_MAX_BPR_REG_LEN] = {};
int ret;
- dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+ /* Check length and offset for 64k alignment */
+ if ((ofs & (SZ_64K - 1)) || (len & (SZ_64K - 1))) {
+ dev_err(nor->dev, "length or offset is not 64KiB allighned\n");
+ return -EINVAL;
+ }
- write_enable(nor);
+ if (ofs + len > mtd->size) {
+ dev_err(nor->dev, "range is more than device size: %#llx + %#llx > %#llx\n",
+ ofs, len, mtd->size);
+ return -EINVAL;
+ }
- nor->sst_write_second = false;
+ /* SST26 family has only 16 Mbit, 32 Mbit and 64 Mbit IC */
+ if (mtd->size != SZ_2M &&
+ mtd->size != SZ_4M &&
+ mtd->size != SZ_8M)
+ return -EINVAL;
- actual = to % 2;
- /* Start write from odd address. */
- if (actual) {
+ bpr_size = 2 + (mtd->size / SZ_64K / 8);
+
+ ret = nor->read_reg(nor, SPINOR_OP_READ_BPR, bpr_buff, bpr_size);
+ if (ret < 0) {
+ dev_err(nor->dev, "fail to read block-protection register\n");
+ return ret;
+ }
+
+ rptr_64k = min_t(u32, ofs + len, mtd->size - SST26_BOUND_REG_SIZE);
+ lptr_64k = max_t(u32, ofs, SST26_BOUND_REG_SIZE);
+
+ upper_64k = ((ofs + len) > (mtd->size - SST26_BOUND_REG_SIZE));
+ lower_64k = (ofs < SST26_BOUND_REG_SIZE);
+
+ /* Lower bits in block-protection register are about 64k region */
+ bpr_ptr = lptr_64k / SZ_64K - 1;
+
+ /* Process 64K blocks region */
+ while (lptr_64k < rptr_64k) {
+ if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
+ return EACCES;
+
+ bpr_ptr++;
+ lptr_64k += SZ_64K;
+ }
+
+ /* 32K and 8K region bits in BPR are after 64k region bits */
+ bpr_ptr = (mtd->size - 2 * SST26_BOUND_REG_SIZE) / SZ_64K;
+
+ /* Process lower 32K block region */
+ if (lower_64k)
+ if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
+ return EACCES;
+
+ bpr_ptr++;
+
+ /* Process upper 32K block region */
+ if (upper_64k)
+ if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
+ return EACCES;
+
+ bpr_ptr++;
+
+ /* Process lower 8K block regions */
+ for (i = 0; i < SST26_BPR_8K_NUM; i++) {
+ if (lower_64k)
+ if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
+ return EACCES;
+
+ /* In 8K area BPR has both read and write protection bits */
+ bpr_ptr += 2;
+ }
+
+ /* Process upper 8K block regions */
+ for (i = 0; i < SST26_BPR_8K_NUM; i++) {
+ if (upper_64k)
+ if (sst26_process_bpr(bpr_size, bpr_buff, bpr_ptr, ctl))
+ return EACCES;
+
+ /* In 8K area BPR has both read and write protection bits */
+ bpr_ptr += 2;
+ }
+
+ /* If we check region status we don't need to write BPR back */
+ if (ctl == SST26_CTL_CHECK)
+ return 0;
+
+ ret = nor->write_reg(nor, SPINOR_OP_WRITE_BPR, bpr_buff, bpr_size);
+ if (ret < 0) {
+ dev_err(nor->dev, "fail to write block-protection register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int sst26_unlock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ return sst26_lock_ctl(nor, ofs, len, SST26_CTL_UNLOCK);
+}
+
+static int sst26_lock(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ return sst26_lock_ctl(nor, ofs, len, SST26_CTL_LOCK);
+}
+
+/*
+ * Returns EACCES (positive value) if region is locked, 0 if region is unlocked,
+ * and negative on errors.
+ */
+static int sst26_is_locked(struct spi_nor *nor, loff_t ofs, uint64_t len)
+{
+ /*
+ * is_locked function is used for check before reading or erasing flash
+ * region, so offset and length might be not 64k allighned, so adjust
+ * them to be 64k allighned as sst26_lock_ctl works only with 64k
+ * allighned regions.
+ */
+ ofs -= ofs & (SZ_64K - 1);
+ len = len & (SZ_64K - 1) ? (len & ~(SZ_64K - 1)) + SZ_64K : len;
+
+ return sst26_lock_ctl(nor, ofs, len, SST26_CTL_CHECK);
+}
+
+static int sst_write_byteprogram(struct spi_nor *nor, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ size_t actual;
+ int ret = 0;
+
+ for (actual = 0; actual < len; actual++) {
nor->program_opcode = SPINOR_OP_BP;
+ write_enable(nor);
/* write one byte. */
- ret = nor->write(nor, to, 1, buf);
+ ret = nor->write(nor, to, 1, buf + actual);
if (ret < 0)
goto sst_write_err;
ret = spi_nor_wait_till_ready(nor);
if (ret)
goto sst_write_err;
+ to++;
}
- to += actual;
-
- /* Write out most of the data here. */
- for (; actual < len - 1; actual += 2) {
- nor->program_opcode = SPINOR_OP_AAI_WP;
- /* write two bytes. */
+sst_write_err:
+ write_disable(nor);
+ return ret;
+}
+
+static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ struct spi_slave *spi = nor->spi;
+ size_t actual;
+ int ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+ if (spi->mode & SPI_TX_BYTE)
+ return sst_write_byteprogram(nor, to, len, retlen, buf);
+
+ write_enable(nor);
+
+ nor->sst_write_second = false;
+
+ actual = to % 2;
+ /* Start write from odd address. */
+ if (actual) {
+ nor->program_opcode = SPINOR_OP_BP;
+
+ /* write one byte. */
+ ret = nor->write(nor, to, 1, buf);
+ if (ret < 0)
+ goto sst_write_err;
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto sst_write_err;
+ }
+ to += actual;
+
+ /* Write out most of the data here. */
+ for (; actual < len - 1; actual += 2) {
+ nor->program_opcode = SPINOR_OP_AAI_WP;
+
+ /* write two bytes. */
ret = nor->write(nor, to, 2, buf + actual);
if (ret < 0)
goto sst_write_err;
dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+ if (!len)
+ return 0;
+
for (i = 0; i < len; ) {
ssize_t written;
loff_t addr = to + i;
* If page_size is a power of two, the offset can be quickly
* calculated with an AND operation. On the other cases we
* need to do a modulus operation (more expensive).
- * Power of two numbers have only one bit set and we can use
- * the instruction hweight32 to detect if we need to do a
- * modulus (do_div()) or not.
*/
- if (hweight32(nor->page_size) == 1) {
+ if (is_power_of_2(nor->page_size)) {
page_offset = addr & (nor->page_size - 1);
} else {
u64 aux = addr;
page_remain = min_t(size_t,
nor->page_size - page_offset, len - i);
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = write_bar(nor, addr);
+ if (ret < 0)
+ return ret;
+#endif
write_enable(nor);
ret = nor->write(nor, addr, page_remain, buf + i);
if (ret < 0)
goto write_err;
*retlen += written;
i += written;
- if (written != page_remain) {
- ret = -EIO;
- goto write_err;
- }
}
write_err:
+#ifdef CONFIG_SPI_FLASH_BAR
+ ret = clean_bar(nor);
+#endif
return ret;
}
return 0;
}
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/**
+ * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories not supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_dbg(nor->dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+ sr_cr[1] = CR_QUAD_EN_SPAN;
+
+ return write_sr_cr(nor, sr_cr);
+}
+
+#endif /* CONFIG_SPI_FLASH_SFDP_SUPPORT */
#endif /* CONFIG_SPI_FLASH_SPANSION */
struct spi_nor_read_command {
pp->proto = proto;
}
+#if CONFIG_IS_ENABLED(SPI_FLASH_SFDP_SUPPORT)
+/*
+ * Serial Flash Discoverable Parameters (SFDP) parsing.
+ */
+
+/**
+ * spi_nor_read_sfdp() - read Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @addr: offset in the SFDP area to start reading data from
+ * @len: number of bytes to read
+ * @buf: buffer where the SFDP data are copied into (dma-safe memory)
+ *
+ * Whatever the actual numbers of bytes for address and dummy cycles are
+ * for (Fast) Read commands, the Read SFDP (5Ah) instruction is always
+ * followed by a 3-byte address and 8 dummy clock cycles.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
+ size_t len, void *buf)
+{
+ u8 addr_width, read_opcode, read_dummy;
+ int ret;
+
+ read_opcode = nor->read_opcode;
+ addr_width = nor->addr_width;
+ read_dummy = nor->read_dummy;
+
+ nor->read_opcode = SPINOR_OP_RDSFDP;
+ nor->addr_width = 3;
+ nor->read_dummy = 8;
+
+ while (len) {
+ ret = nor->read(nor, addr, len, (u8 *)buf);
+ if (!ret || ret > len) {
+ ret = -EIO;
+ goto read_err;
+ }
+ if (ret < 0)
+ goto read_err;
+
+ buf += ret;
+ addr += ret;
+ len -= ret;
+ }
+ ret = 0;
+
+read_err:
+ nor->read_opcode = read_opcode;
+ nor->addr_width = addr_width;
+ nor->read_dummy = read_dummy;
+
+ return ret;
+}
+
+struct sfdp_parameter_header {
+ u8 id_lsb;
+ u8 minor;
+ u8 major;
+ u8 length; /* in double words */
+ u8 parameter_table_pointer[3]; /* byte address */
+ u8 id_msb;
+};
+
+#define SFDP_PARAM_HEADER_ID(p) (((p)->id_msb << 8) | (p)->id_lsb)
+#define SFDP_PARAM_HEADER_PTP(p) \
+ (((p)->parameter_table_pointer[2] << 16) | \
+ ((p)->parameter_table_pointer[1] << 8) | \
+ ((p)->parameter_table_pointer[0] << 0))
+
+#define SFDP_BFPT_ID 0xff00 /* Basic Flash Parameter Table */
+#define SFDP_SECTOR_MAP_ID 0xff81 /* Sector Map Table */
+#define SFDP_SST_ID 0x01bf /* Manufacturer specific Table */
+
+#define SFDP_SIGNATURE 0x50444653U
+#define SFDP_JESD216_MAJOR 1
+#define SFDP_JESD216_MINOR 0
+#define SFDP_JESD216A_MINOR 5
+#define SFDP_JESD216B_MINOR 6
+
+struct sfdp_header {
+ u32 signature; /* Ox50444653U <=> "SFDP" */
+ u8 minor;
+ u8 major;
+ u8 nph; /* 0-base number of parameter headers */
+ u8 unused;
+
+ /* Basic Flash Parameter Table. */
+ struct sfdp_parameter_header bfpt_header;
+};
+
+/* Basic Flash Parameter Table */
+
+/*
+ * JESD216 rev B defines a Basic Flash Parameter Table of 16 DWORDs.
+ * They are indexed from 1 but C arrays are indexed from 0.
+ */
+#define BFPT_DWORD(i) ((i) - 1)
+#define BFPT_DWORD_MAX 16
+
+/* The first version of JESB216 defined only 9 DWORDs. */
+#define BFPT_DWORD_MAX_JESD216 9
+
+/* 1st DWORD. */
+#define BFPT_DWORD1_FAST_READ_1_1_2 BIT(16)
+#define BFPT_DWORD1_ADDRESS_BYTES_MASK GENMASK(18, 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_ONLY (0x0UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 (0x1UL << 17)
+#define BFPT_DWORD1_ADDRESS_BYTES_4_ONLY (0x2UL << 17)
+#define BFPT_DWORD1_DTR BIT(19)
+#define BFPT_DWORD1_FAST_READ_1_2_2 BIT(20)
+#define BFPT_DWORD1_FAST_READ_1_4_4 BIT(21)
+#define BFPT_DWORD1_FAST_READ_1_1_4 BIT(22)
+
+/* 5th DWORD. */
+#define BFPT_DWORD5_FAST_READ_2_2_2 BIT(0)
+#define BFPT_DWORD5_FAST_READ_4_4_4 BIT(4)
+
+/* 11th DWORD. */
+#define BFPT_DWORD11_PAGE_SIZE_SHIFT 4
+#define BFPT_DWORD11_PAGE_SIZE_MASK GENMASK(7, 4)
+
+/* 15th DWORD. */
+
+/*
+ * (from JESD216 rev B)
+ * Quad Enable Requirements (QER):
+ * - 000b: Device does not have a QE bit. Device detects 1-1-4 and 1-4-4
+ * reads based on instruction. DQ3/HOLD# functions are hold during
+ * instruction phase.
+ * - 001b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * Writing only one byte to the status register has the side-effect of
+ * clearing status register 2, including the QE bit. The 100b code is
+ * used if writing one byte to the status register does not modify
+ * status register 2.
+ * - 010b: QE is bit 6 of status register 1. It is set via Write Status with
+ * one data byte where bit 6 is one.
+ * [...]
+ * - 011b: QE is bit 7 of status register 2. It is set via Write status
+ * register 2 instruction 3Eh with one data byte where bit 7 is one.
+ * [...]
+ * The status register 2 is read using instruction 3Fh.
+ * - 100b: QE is bit 1 of status register 2. It is set via Write Status with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ * In contrast to the 001b code, writing one byte to the status
+ * register does not modify status register 2.
+ * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
+ * Read Status instruction 05h. Status register2 is read using
+ * instruction 35h. QE is set via Writ Status instruction 01h with
+ * two data bytes where bit 1 of the second byte is one.
+ * [...]
+ */
+#define BFPT_DWORD15_QER_MASK GENMASK(22, 20)
+#define BFPT_DWORD15_QER_NONE (0x0UL << 20) /* Micron */
+#define BFPT_DWORD15_QER_SR2_BIT1_BUGGY (0x1UL << 20)
+#define BFPT_DWORD15_QER_SR1_BIT6 (0x2UL << 20) /* Macronix */
+#define BFPT_DWORD15_QER_SR2_BIT7 (0x3UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)
+#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20) /* Spansion */
+
+struct sfdp_bfpt {
+ u32 dwords[BFPT_DWORD_MAX];
+};
+
+/* Fast Read settings. */
+
+static void
+spi_nor_set_read_settings_from_bfpt(struct spi_nor_read_command *read,
+ u16 half,
+ enum spi_nor_protocol proto)
+{
+ read->num_mode_clocks = (half >> 5) & 0x07;
+ read->num_wait_states = (half >> 0) & 0x1f;
+ read->opcode = (half >> 8) & 0xff;
+ read->proto = proto;
+}
+
+struct sfdp_bfpt_read {
+ /* The Fast Read x-y-z hardware capability in params->hwcaps.mask. */
+ u32 hwcaps;
+
+ /*
+ * The <supported_bit> bit in <supported_dword> BFPT DWORD tells us
+ * whether the Fast Read x-y-z command is supported.
+ */
+ u32 supported_dword;
+ u32 supported_bit;
+
+ /*
+ * The half-word at offset <setting_shift> in <setting_dword> BFPT DWORD
+ * encodes the op code, the number of mode clocks and the number of wait
+ * states to be used by Fast Read x-y-z command.
+ */
+ u32 settings_dword;
+ u32 settings_shift;
+
+ /* The SPI protocol for this Fast Read x-y-z command. */
+ enum spi_nor_protocol proto;
+};
+
+static const struct sfdp_bfpt_read sfdp_bfpt_reads[] = {
+ /* Fast Read 1-1-2 */
+ {
+ SNOR_HWCAPS_READ_1_1_2,
+ BFPT_DWORD(1), BIT(16), /* Supported bit */
+ BFPT_DWORD(4), 0, /* Settings */
+ SNOR_PROTO_1_1_2,
+ },
+
+ /* Fast Read 1-2-2 */
+ {
+ SNOR_HWCAPS_READ_1_2_2,
+ BFPT_DWORD(1), BIT(20), /* Supported bit */
+ BFPT_DWORD(4), 16, /* Settings */
+ SNOR_PROTO_1_2_2,
+ },
+
+ /* Fast Read 2-2-2 */
+ {
+ SNOR_HWCAPS_READ_2_2_2,
+ BFPT_DWORD(5), BIT(0), /* Supported bit */
+ BFPT_DWORD(6), 16, /* Settings */
+ SNOR_PROTO_2_2_2,
+ },
+
+ /* Fast Read 1-1-4 */
+ {
+ SNOR_HWCAPS_READ_1_1_4,
+ BFPT_DWORD(1), BIT(22), /* Supported bit */
+ BFPT_DWORD(3), 16, /* Settings */
+ SNOR_PROTO_1_1_4,
+ },
+
+ /* Fast Read 1-4-4 */
+ {
+ SNOR_HWCAPS_READ_1_4_4,
+ BFPT_DWORD(1), BIT(21), /* Supported bit */
+ BFPT_DWORD(3), 0, /* Settings */
+ SNOR_PROTO_1_4_4,
+ },
+
+ /* Fast Read 4-4-4 */
+ {
+ SNOR_HWCAPS_READ_4_4_4,
+ BFPT_DWORD(5), BIT(4), /* Supported bit */
+ BFPT_DWORD(7), 16, /* Settings */
+ SNOR_PROTO_4_4_4,
+ },
+};
+
+struct sfdp_bfpt_erase {
+ /*
+ * The half-word at offset <shift> in DWORD <dwoard> encodes the
+ * op code and erase sector size to be used by Sector Erase commands.
+ */
+ u32 dword;
+ u32 shift;
+};
+
+static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = {
+ /* Erase Type 1 in DWORD8 bits[15:0] */
+ {BFPT_DWORD(8), 0},
+
+ /* Erase Type 2 in DWORD8 bits[31:16] */
+ {BFPT_DWORD(8), 16},
+
+ /* Erase Type 3 in DWORD9 bits[15:0] */
+ {BFPT_DWORD(9), 0},
+
+ /* Erase Type 4 in DWORD9 bits[31:16] */
+ {BFPT_DWORD(9), 16},
+};
+
+static int spi_nor_hwcaps_read2cmd(u32 hwcaps);
+
+/**
+ * spi_nor_parse_bfpt() - read and parse the Basic Flash Parameter Table.
+ * @nor: pointer to a 'struct spi_nor'
+ * @bfpt_header: pointer to the 'struct sfdp_parameter_header' describing
+ * the Basic Flash Parameter Table length and version
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Basic Flash Parameter Table is the main and only mandatory table as
+ * defined by the SFDP (JESD216) specification.
+ * It provides us with the total size (memory density) of the data array and
+ * the number of address bytes for Fast Read, Page Program and Sector Erase
+ * commands.
+ * For Fast READ commands, it also gives the number of mode clock cycles and
+ * wait states (regrouped in the number of dummy clock cycles) for each
+ * supported instruction op code.
+ * For Page Program, the page size is now available since JESD216 rev A, however
+ * the supported instruction op codes are still not provided.
+ * For Sector Erase commands, this table stores the supported instruction op
+ * codes and the associated sector sizes.
+ * Finally, the Quad Enable Requirements (QER) are also available since JESD216
+ * rev A. The QER bits encode the manufacturer dependent procedure to be
+ * executed to set the Quad Enable (QE) bit in some internal register of the
+ * Quad SPI memory. Indeed the QE bit, when it exists, must be set before
+ * sending any Quad SPI command to the memory. Actually, setting the QE bit
+ * tells the memory to reassign its WP# and HOLD#/RESET# pins to functions IO2
+ * and IO3 hence enabling 4 (Quad) I/O lines.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_bfpt(struct spi_nor *nor,
+ const struct sfdp_parameter_header *bfpt_header,
+ struct spi_nor_flash_parameter *params)
+{
+ struct mtd_info *mtd = &nor->mtd;
+ struct sfdp_bfpt bfpt;
+ size_t len;
+ int i, cmd, err;
+ u32 addr;
+ u16 half;
+
+ /* JESD216 Basic Flash Parameter Table length is at least 9 DWORDs. */
+ if (bfpt_header->length < BFPT_DWORD_MAX_JESD216)
+ return -EINVAL;
+
+ /* Read the Basic Flash Parameter Table. */
+ len = min_t(size_t, sizeof(bfpt),
+ bfpt_header->length * sizeof(u32));
+ addr = SFDP_PARAM_HEADER_PTP(bfpt_header);
+ memset(&bfpt, 0, sizeof(bfpt));
+ err = spi_nor_read_sfdp(nor, addr, len, &bfpt);
+ if (err < 0)
+ return err;
+
+ /* Fix endianness of the BFPT DWORDs. */
+ for (i = 0; i < BFPT_DWORD_MAX; i++)
+ bfpt.dwords[i] = le32_to_cpu(bfpt.dwords[i]);
+
+ /* Number of address bytes. */
+ switch (bfpt.dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) {
+ case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY:
+ nor->addr_width = 3;
+ break;
+
+ case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY:
+ nor->addr_width = 4;
+ break;
+
+ default:
+ break;
+ }
+
+ /* Flash Memory Density (in bits). */
+ params->size = bfpt.dwords[BFPT_DWORD(2)];
+ if (params->size & BIT(31)) {
+ params->size &= ~BIT(31);
+
+ /*
+ * Prevent overflows on params->size. Anyway, a NOR of 2^64
+ * bits is unlikely to exist so this error probably means
+ * the BFPT we are reading is corrupted/wrong.
+ */
+ if (params->size > 63)
+ return -EINVAL;
+
+ params->size = 1ULL << params->size;
+ } else {
+ params->size++;
+ }
+ params->size >>= 3; /* Convert to bytes. */
+
+ /* Fast Read settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_reads); i++) {
+ const struct sfdp_bfpt_read *rd = &sfdp_bfpt_reads[i];
+ struct spi_nor_read_command *read;
+
+ if (!(bfpt.dwords[rd->supported_dword] & rd->supported_bit)) {
+ params->hwcaps.mask &= ~rd->hwcaps;
+ continue;
+ }
+
+ params->hwcaps.mask |= rd->hwcaps;
+ cmd = spi_nor_hwcaps_read2cmd(rd->hwcaps);
+ read = ¶ms->reads[cmd];
+ half = bfpt.dwords[rd->settings_dword] >> rd->settings_shift;
+ spi_nor_set_read_settings_from_bfpt(read, half, rd->proto);
+ }
+
+ /* Sector Erase settings. */
+ for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_erases); i++) {
+ const struct sfdp_bfpt_erase *er = &sfdp_bfpt_erases[i];
+ u32 erasesize;
+ u8 opcode;
+
+ half = bfpt.dwords[er->dword] >> er->shift;
+ erasesize = half & 0xff;
+
+ /* erasesize == 0 means this Erase Type is not supported. */
+ if (!erasesize)
+ continue;
+
+ erasesize = 1U << erasesize;
+ opcode = (half >> 8) & 0xff;
+#ifdef CONFIG_SPI_FLASH_USE_4K_SECTORS
+ if (erasesize == SZ_4K) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ break;
+ }
+#endif
+ if (!mtd->erasesize || mtd->erasesize < erasesize) {
+ nor->erase_opcode = opcode;
+ mtd->erasesize = erasesize;
+ }
+ }
+
+ /* Stop here if not JESD216 rev A or later. */
+ if (bfpt_header->length < BFPT_DWORD_MAX)
+ return 0;
+
+ /* Page size: this field specifies 'N' so the page size = 2^N bytes. */
+ params->page_size = bfpt.dwords[BFPT_DWORD(11)];
+ params->page_size &= BFPT_DWORD11_PAGE_SIZE_MASK;
+ params->page_size >>= BFPT_DWORD11_PAGE_SIZE_SHIFT;
+ params->page_size = 1U << params->page_size;
+
+ /* Quad Enable Requirements. */
+ switch (bfpt.dwords[BFPT_DWORD(15)] & BFPT_DWORD15_QER_MASK) {
+ case BFPT_DWORD15_QER_NONE:
+ params->quad_enable = NULL;
+ break;
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1_BUGGY:
+ case BFPT_DWORD15_QER_SR2_BIT1_NO_RD:
+ params->quad_enable = spansion_no_read_cr_quad_enable;
+ break;
+#endif
+#ifdef CONFIG_SPI_FLASH_MACRONIX
+ case BFPT_DWORD15_QER_SR1_BIT6:
+ params->quad_enable = macronix_quad_enable;
+ break;
+#endif
+#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
+ case BFPT_DWORD15_QER_SR2_BIT1:
+ params->quad_enable = spansion_read_cr_quad_enable;
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * spi_nor_parse_microchip_sfdp() - parse the Microchip manufacturer specific
+ * SFDP table.
+ * @nor: pointer to a 'struct spi_nor'.
+ * @param_header: pointer to the SFDP parameter header.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int
+spi_nor_parse_microchip_sfdp(struct spi_nor *nor,
+ const struct sfdp_parameter_header *param_header)
+{
+ size_t size;
+ u32 addr;
+ int ret;
+
+ size = param_header->length * sizeof(u32);
+ addr = SFDP_PARAM_HEADER_PTP(param_header);
+
+ nor->manufacturer_sfdp = devm_kmalloc(nor->dev, size, GFP_KERNEL);
+ if (!nor->manufacturer_sfdp)
+ return -ENOMEM;
+
+ ret = spi_nor_read_sfdp(nor, addr, size, nor->manufacturer_sfdp);
+
+ return ret;
+}
+
+/**
+ * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
+ * @nor: pointer to a 'struct spi_nor'
+ * @params: pointer to the 'struct spi_nor_flash_parameter' to be
+ * filled
+ *
+ * The Serial Flash Discoverable Parameters are described by the JEDEC JESD216
+ * specification. This is a standard which tends to supported by almost all
+ * (Q)SPI memory manufacturers. Those hard-coded tables allow us to learn at
+ * runtime the main parameters needed to perform basic SPI flash operations such
+ * as Fast Read, Page Program or Sector Erase commands.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ const struct sfdp_parameter_header *param_header, *bfpt_header;
+ struct sfdp_parameter_header *param_headers = NULL;
+ struct sfdp_header header;
+ size_t psize;
+ int i, err;
+
+ /* Get the SFDP header. */
+ err = spi_nor_read_sfdp(nor, 0, sizeof(header), &header);
+ if (err < 0)
+ return err;
+
+ /* Check the SFDP header version. */
+ if (le32_to_cpu(header.signature) != SFDP_SIGNATURE ||
+ header.major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Verify that the first and only mandatory parameter header is a
+ * Basic Flash Parameter Table header as specified in JESD216.
+ */
+ bfpt_header = &header.bfpt_header;
+ if (SFDP_PARAM_HEADER_ID(bfpt_header) != SFDP_BFPT_ID ||
+ bfpt_header->major != SFDP_JESD216_MAJOR)
+ return -EINVAL;
+
+ /*
+ * Allocate memory then read all parameter headers with a single
+ * Read SFDP command. These parameter headers will actually be parsed
+ * twice: a first time to get the latest revision of the basic flash
+ * parameter table, then a second time to handle the supported optional
+ * tables.
+ * Hence we read the parameter headers once for all to reduce the
+ * processing time. Also we use kmalloc() instead of devm_kmalloc()
+ * because we don't need to keep these parameter headers: the allocated
+ * memory is always released with kfree() before exiting this function.
+ */
+ if (header.nph) {
+ psize = header.nph * sizeof(*param_headers);
+
+ param_headers = kmalloc(psize, GFP_KERNEL);
+ if (!param_headers)
+ return -ENOMEM;
+
+ err = spi_nor_read_sfdp(nor, sizeof(header),
+ psize, param_headers);
+ if (err < 0) {
+ dev_err(dev, "failed to read SFDP parameter headers\n");
+ goto exit;
+ }
+ }
+
+ /*
+ * Check other parameter headers to get the latest revision of
+ * the basic flash parameter table.
+ */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ if (SFDP_PARAM_HEADER_ID(param_header) == SFDP_BFPT_ID &&
+ param_header->major == SFDP_JESD216_MAJOR &&
+ (param_header->minor > bfpt_header->minor ||
+ (param_header->minor == bfpt_header->minor &&
+ param_header->length > bfpt_header->length)))
+ bfpt_header = param_header;
+ }
+
+ err = spi_nor_parse_bfpt(nor, bfpt_header, params);
+ if (err)
+ goto exit;
+
+ /* Parse other parameter headers. */
+ for (i = 0; i < header.nph; i++) {
+ param_header = ¶m_headers[i];
+
+ switch (SFDP_PARAM_HEADER_ID(param_header)) {
+ case SFDP_SECTOR_MAP_ID:
+ dev_info(dev, "non-uniform erase sector maps are not supported yet.\n");
+ break;
+
+ case SFDP_SST_ID:
+ err = spi_nor_parse_microchip_sfdp(nor, param_header);
+ break;
+
+ default:
+ break;
+ }
+
+ if (err) {
+ dev_warn(dev, "Failed to parse optional parameter table: %04x\n",
+ SFDP_PARAM_HEADER_ID(param_header));
+ /*
+ * Let's not drop all information we extracted so far
+ * if optional table parsers fail. In case of failing,
+ * each optional parser is responsible to roll back to
+ * the previously known spi_nor data.
+ */
+ err = 0;
+ }
+ }
+
+exit:
+ kfree(param_headers);
+ return err;
+}
+#else
+static int spi_nor_parse_sfdp(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ return -EINVAL;
+}
+#endif /* SPI_FLASH_SFDP_SUPPORT */
+
static int spi_nor_init_params(struct spi_nor *nor,
const struct flash_info *info,
struct spi_nor_flash_parameter *params)
SNOR_PROTO_1_1_4);
}
+ if (info->flags & SPI_NOR_OCTAL_READ) {
+ params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_8;
+ spi_nor_set_read_settings(¶ms->reads[SNOR_CMD_READ_1_1_8],
+ 0, 8, SPINOR_OP_READ_1_1_8,
+ SNOR_PROTO_1_1_8);
+ }
+
/* Page Program settings. */
params->hwcaps.mask |= SNOR_HWCAPS_PP;
spi_nor_set_pp_settings(¶ms->page_programs[SNOR_CMD_PP],
break;
}
}
+
+ /* Override the parameters with data read from SFDP tables. */
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ if ((info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
+ !(info->flags & SPI_NOR_SKIP_SFDP)) {
+ struct spi_nor_flash_parameter sfdp_params;
+
+ memcpy(&sfdp_params, params, sizeof(sfdp_params));
+ if (spi_nor_parse_sfdp(nor, &sfdp_params)) {
+ nor->addr_width = 0;
+ nor->mtd.erasesize = 0;
+ } else {
+ memcpy(params, &sfdp_params, sizeof(*params));
+ }
+ }
+
+ return 0;
}
static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
{
struct mtd_info *mtd = &nor->mtd;
+ /* Do nothing if already configured from SFDP. */
+ if (mtd->erasesize)
+ return 0;
+
#ifdef CONFIG_SPI_FLASH_USE_4K_SECTORS
/* prefer "small sector" erase if possible */
if (info->flags & SECT_4K) {
}
}
+ if (nor->addr_width == 4 &&
+ (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) &&
+ !(nor->info->flags & SPI_NOR_4B_OPCODES)) {
+ /*
+ * If the RESET# pin isn't hooked up properly, or the system
+ * otherwise doesn't perform a reset command in the boot
+ * sequence, it's impossible to 100% protect against unexpected
+ * reboots (e.g., crashes). Warn the user (or hopefully, system
+ * designer) that this is bad.
+ */
+ if (nor->flags & SNOR_F_BROKEN_RESET)
+ printf("enabling reset hack; may not recover from unexpected reboots\n");
+ set_4byte(nor, nor->info, 1);
+ }
+
return 0;
}
nor->read_reg = spi_nor_read_reg;
nor->write_reg = spi_nor_write_reg;
- if (spi->mode & SPI_RX_QUAD) {
+ if (spi->mode & SPI_RX_OCTAL) {
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_8;
+
+ if (spi->mode & SPI_TX_OCTAL)
+ hwcaps.mask |= (SNOR_HWCAPS_READ_1_8_8 |
+ SNOR_HWCAPS_PP_1_1_8 |
+ SNOR_HWCAPS_PP_1_8_8);
+ } else if (spi->mode & SPI_RX_QUAD) {
hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
if (spi->mode & SPI_TX_QUAD)
info = spi_nor_read_id(nor);
if (IS_ERR_OR_NULL(info))
return -ENOENT;
-
+ /* Parse the Serial Flash Discoverable Parameters table. */
ret = spi_nor_init_params(nor, info, ¶ms);
if (ret)
return ret;
#endif
#ifdef CONFIG_SPI_FLASH_SST
+ /*
+ * sst26 series block protection implementation differs from other
+ * series.
+ */
+ if (info->flags & SPI_NOR_HAS_SST26LOCK) {
+ nor->flash_lock = sst26_lock;
+ nor->flash_unlock = sst26_unlock;
+ nor->flash_is_locked = sst26_is_locked;
+ }
+
/* sst nor chips use AAI word program */
if (info->flags & SST_WRITE)
mtd->_write = sst_write;
if (ret)
return ret;
- if (info->addr_width) {
+ if (nor->addr_width) {
+ /* already configured from SFDP */
+ } else if (info->addr_width) {
nor->addr_width = info->addr_width;
+ } else if (mtd->size > SZ_16M) {
+#ifndef CONFIG_SPI_FLASH_BAR
+ /* enable 4-byte addressing if the device exceeds 16MiB */
+ nor->addr_width = 4;
+ if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+ info->flags & SPI_NOR_4B_OPCODES)
+ spi_nor_set_4byte_opcodes(nor, info);
+#else
+ /* Configure the BAR - discover bank cmds and read current bank */
+ nor->addr_width = 3;
+ ret = read_bar(nor, info);
+ if (ret < 0)
+ return ret;
+#endif
} else {
nor->addr_width = 3;
}
return 0;
}
+
+/* U-Boot specific functions, need to extend MTD to support these */
+int spi_flash_cmd_get_sw_write_prot(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+
+ if (sr < 0)
+ return sr;
+
+ return (sr >> 2) & 7;
+}
projects / platform / kernel / u-boot.git / blobdiff