#if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35)
#include <asm/arch/imx-regs.h>
#endif
+#include <fsl_nfc.h>
#define DRIVER_NAME "mxc_nand"
-/*
- * TODO: Use same register defs here as nand_spl mxc nand driver.
- */
-/*
- * Register map and bit definitions for the Freescale NAND Flash Controller
- * present in various i.MX devices.
- *
- * MX31 and MX27 have version 1 which has
- * 4 512 byte main buffers and
- * 4 16 byte spare buffers
- * to support up to 2K byte pagesize nand.
- * Reading or writing a 2K page requires 4 FDI/FDO cycles.
- *
- * MX25 has version 1.1 which has
- * 8 512 byte main buffers and
- * 8 64 byte spare buffers
- * to support up to 4K byte pagesize nand.
- * Reading or writing a 2K or 4K page requires only 1 FDI/FDO cycle.
- * Also some of registers are moved and/or changed meaning as seen below.
- */
-#if defined(CONFIG_MX31) || defined(CONFIG_MX27)
-#define MXC_NFC_V1
-#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
-#define MXC_NFC_V1_1
-#else
-#warning "MXC NFC version not defined"
-#endif
-
-#if defined(MXC_NFC_V1)
-#define NAND_MXC_NR_BUFS 4
-#define NAND_MXC_SPARE_BUF_SIZE 16
-#define NAND_MXC_REG_OFFSET 0xe00
-#define is_mxc_nfc_11() 0
-#elif defined(MXC_NFC_V1_1)
-#define NAND_MXC_NR_BUFS 8
-#define NAND_MXC_SPARE_BUF_SIZE 64
-#define NAND_MXC_REG_OFFSET 0x1e00
-#define is_mxc_nfc_11() 1
-#else
-#error "define CONFIG_NAND_MXC_VXXX to use mtd mxc nand driver"
-#endif
-struct nfc_regs {
- uint8_t main_area[NAND_MXC_NR_BUFS][0x200];
- uint8_t spare_area[NAND_MXC_NR_BUFS][NAND_MXC_SPARE_BUF_SIZE];
- /*
- * reserved size is offset of nfc registers
- * minus total main and spare sizes
- */
- uint8_t reserved1[NAND_MXC_REG_OFFSET
- - NAND_MXC_NR_BUFS * (512 + NAND_MXC_SPARE_BUF_SIZE)];
-#if defined(MXC_NFC_V1)
- uint16_t nfc_buf_size;
- uint16_t reserved2;
- uint16_t nfc_buf_addr;
- uint16_t nfc_flash_addr;
- uint16_t nfc_flash_cmd;
- uint16_t nfc_config;
- uint16_t nfc_ecc_status_result;
- uint16_t nfc_rsltmain_area;
- uint16_t nfc_rsltspare_area;
- uint16_t nfc_wrprot;
- uint16_t nfc_unlockstart_blkaddr;
- uint16_t nfc_unlockend_blkaddr;
- uint16_t nfc_nf_wrprst;
- uint16_t nfc_config1;
- uint16_t nfc_config2;
-#elif defined(MXC_NFC_V1_1)
- uint16_t reserved2[2];
- uint16_t nfc_buf_addr;
- uint16_t nfc_flash_addr;
- uint16_t nfc_flash_cmd;
- uint16_t nfc_config;
- uint16_t nfc_ecc_status_result;
- uint16_t nfc_ecc_status_result2;
- uint16_t nfc_spare_area_size;
- uint16_t nfc_wrprot;
- uint16_t reserved3[2];
- uint16_t nfc_nf_wrprst;
- uint16_t nfc_config1;
- uint16_t nfc_config2;
- uint16_t reserved4;
- uint16_t nfc_unlockstart_blkaddr;
- uint16_t nfc_unlockend_blkaddr;
- uint16_t nfc_unlockstart_blkaddr1;
- uint16_t nfc_unlockend_blkaddr1;
- uint16_t nfc_unlockstart_blkaddr2;
- uint16_t nfc_unlockend_blkaddr2;
- uint16_t nfc_unlockstart_blkaddr3;
- uint16_t nfc_unlockend_blkaddr3;
-#endif
-};
-
-/*
- * Set INT to 0, FCMD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Command operation
- */
-#define NFC_CMD 0x1
-
-/*
- * Set INT to 0, FADD to 1, rest to 0 in NFC_CONFIG2 Register
- * for Address operation
- */
-#define NFC_ADDR 0x2
-
-/*
- * Set INT to 0, FDI to 1, rest to 0 in NFC_CONFIG2 Register
- * for Input operation
- */
-#define NFC_INPUT 0x4
-
-/*
- * Set INT to 0, FDO to 001, rest to 0 in NFC_CONFIG2 Register
- * for Data Output operation
- */
-#define NFC_OUTPUT 0x8
-
-/*
- * Set INT to 0, FD0 to 010, rest to 0 in NFC_CONFIG2 Register
- * for Read ID operation
- */
-#define NFC_ID 0x10
-
-/*
- * Set INT to 0, FDO to 100, rest to 0 in NFC_CONFIG2 Register
- * for Read Status operation
- */
-#define NFC_STATUS 0x20
-
-/*
- * Set INT to 1, rest to 0 in NFC_CONFIG2 Register for Read
- * Status operation
- */
-#define NFC_INT 0x8000
-
-#ifdef MXC_NFC_V1_1
-#define NFC_4_8N_ECC (1 << 0)
-#else
-#define NFC_4_8N_ECC 0
-#endif
-#define NFC_SP_EN (1 << 2)
-#define NFC_ECC_EN (1 << 3)
-#define NFC_BIG (1 << 5)
-#define NFC_RST (1 << 6)
-#define NFC_CE (1 << 7)
-#define NFC_ONE_CYCLE (1 << 8)
-
typedef enum {false, true} bool;
struct mxc_nand_host {
- struct mtd_info mtd;
- struct nand_chip *nand;
-
- struct nfc_regs __iomem *regs;
- int spare_only;
- int status_request;
- int pagesize_2k;
- int clk_act;
- uint16_t col_addr;
- unsigned int page_addr;
+ struct mtd_info mtd;
+ struct nand_chip *nand;
+
+ struct fsl_nfc_regs __iomem *regs;
+ int spare_only;
+ int status_request;
+ int pagesize_2k;
+ int clk_act;
+ uint16_t col_addr;
+ unsigned int page_addr;
};
static struct mxc_nand_host mxc_host;
.oobfree = { {2, 4}, {11, 11}, {27, 11}, {43, 11}, {59, 5} },
};
#endif
-#elif defined(MXC_NFC_V1_1)
+#elif defined(MXC_NFC_V2_1)
#ifndef CONFIG_SYS_NAND_LARGEPAGE
static struct nand_ecclayout nand_hw_eccoob = {
.eccbytes = 9,
#endif
#endif
-#ifdef CONFIG_MX27
-static int is_16bit_nand(void)
-{
- struct system_control_regs *sc_regs =
- (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
-
- if (readl(&sc_regs->fmcr) & NF_16BIT_SEL)
- return 1;
- else
- return 0;
-}
-#elif defined(CONFIG_MX31)
-static int is_16bit_nand(void)
-{
- struct clock_control_regs *sc_regs =
- (struct clock_control_regs *)CCM_BASE;
-
- if (readl(&sc_regs->rcsr) & CCM_RCSR_NF16B)
- return 1;
- else
- return 0;
-}
-#elif defined(CONFIG_MX25) || defined(CONFIG_MX35)
static int is_16bit_nand(void)
{
- struct ccm_regs *ccm =
- (struct ccm_regs *)IMX_CCM_BASE;
-
- if (readl(&ccm->rcsr) & CCM_RCSR_NF_16BIT_SEL)
- return 1;
- else
- return 0;
-}
+#if defined(CONFIG_SYS_NAND_BUSWIDTH_16BIT)
+ return 1;
#else
-#warning "8/16 bit NAND autodetection not supported"
-static int is_16bit_nand(void)
-{
return 0;
-}
#endif
+}
static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t size)
{
/*
* This function polls the NANDFC to wait for the basic operation to
- * complete by checking the INT bit of config2 register.
+ * complete by checking the INT bit.
*/
static void wait_op_done(struct mxc_nand_host *host, int max_retries,
uint16_t param)
uint32_t tmp;
while (max_retries-- > 0) {
- if (readw(&host->regs->nfc_config2) & NFC_INT) {
- tmp = readw(&host->regs->nfc_config2);
- tmp &= ~NFC_INT;
- writew(tmp, &host->regs->nfc_config2);
+ tmp = readnfc(&host->regs->config2);
+ if (tmp & NFC_V1_V2_CONFIG2_INT) {
+ tmp &= ~NFC_V1_V2_CONFIG2_INT;
+ writenfc(tmp, &host->regs->config2);
break;
}
udelay(1);
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_cmd(host, 0x%x)\n", cmd);
- writew(cmd, &host->regs->nfc_flash_cmd);
- writew(NFC_CMD, &host->regs->nfc_config2);
+ writenfc(cmd, &host->regs->flash_cmd);
+ writenfc(NFC_CMD, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, cmd);
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_addr(host, 0x%x)\n", addr);
- writew(addr, &host->regs->nfc_flash_addr);
- writew(NFC_ADDR, &host->regs->nfc_config2);
+ writenfc(addr, &host->regs->flash_addr);
+ writenfc(NFC_ADDR, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, addr);
if (spare_only)
MTDDEBUG(MTD_DEBUG_LEVEL1, "send_prog_page (%d)\n", spare_only);
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21()) {
int i;
/*
* The controller copies the 64 bytes of spare data from
}
}
- writew(buf_id, &host->regs->nfc_buf_addr);
+ writenfc(buf_id, &host->regs->buf_addr);
/* Configure spare or page+spare access */
if (!host->pagesize_2k) {
- uint16_t config1 = readw(&host->regs->nfc_config1);
+ uint16_t config1 = readnfc(&host->regs->config1);
if (spare_only)
- config1 |= NFC_SP_EN;
+ config1 |= NFC_CONFIG1_SP_EN;
else
- config1 &= ~(NFC_SP_EN);
- writew(config1, &host->regs->nfc_config1);
+ config1 &= ~NFC_CONFIG1_SP_EN;
+ writenfc(config1, &host->regs->config1);
}
- writew(NFC_INPUT, &host->regs->nfc_config2);
+ writenfc(NFC_INPUT, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, spare_only);
{
MTDDEBUG(MTD_DEBUG_LEVEL3, "send_read_page (%d)\n", spare_only);
- writew(buf_id, &host->regs->nfc_buf_addr);
+ writenfc(buf_id, &host->regs->buf_addr);
/* Configure spare or page+spare access */
if (!host->pagesize_2k) {
- uint32_t config1 = readw(&host->regs->nfc_config1);
+ uint32_t config1 = readnfc(&host->regs->config1);
if (spare_only)
- config1 |= NFC_SP_EN;
+ config1 |= NFC_CONFIG1_SP_EN;
else
- config1 &= ~NFC_SP_EN;
- writew(config1, &host->regs->nfc_config1);
+ config1 &= ~NFC_CONFIG1_SP_EN;
+ writenfc(config1, &host->regs->config1);
}
- writew(NFC_OUTPUT, &host->regs->nfc_config2);
+ writenfc(NFC_OUTPUT, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, spare_only);
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21()) {
int i;
/*
uint16_t tmp;
/* NANDFC buffer 0 is used for device ID output */
- writew(0x0, &host->regs->nfc_buf_addr);
+ writenfc(0x0, &host->regs->buf_addr);
/* Read ID into main buffer */
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_CONFIG1_SP_EN;
+ writenfc(tmp, &host->regs->config1);
- writew(NFC_ID, &host->regs->nfc_config2);
+ writenfc(NFC_ID, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, 0);
/* store the main area1 first word, later do recovery */
store = readl(main_buf);
/* NANDFC buffer 1 is used for device status */
- writew(1, &host->regs->nfc_buf_addr);
+ writenfc(1, &host->regs->buf_addr);
/* Read status into main buffer */
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_SP_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp = readnfc(&host->regs->config1);
+ tmp &= ~NFC_CONFIG1_SP_EN;
+ writenfc(tmp, &host->regs->config1);
- writew(NFC_STATUS, &host->regs->nfc_config2);
+ writenfc(NFC_STATUS, &host->regs->operation);
/* Wait for operation to complete */
wait_op_done(host, TROP_US_DELAY, 0);
return 1;
}
-#ifdef CONFIG_MXC_NAND_HWECC
-static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode)
-{
- /*
- * If HW ECC is enabled, we turn it on during init. There is
- * no need to enable again here.
- */
-}
-
-#ifdef MXC_NFC_V1_1
static void _mxc_nand_enable_hwecc(struct mtd_info *mtd, int on)
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint16_t tmp = readw(&host->regs->nfc_config1);
+ uint16_t tmp = readnfc(&host->regs->config1);
if (on)
- tmp |= NFC_ECC_EN;
+ tmp |= NFC_V1_V2_CONFIG1_ECC_EN;
else
- tmp &= ~NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ tmp &= ~NFC_V1_V2_CONFIG1_ECC_EN;
+ writenfc(tmp, &host->regs->config1);
+}
+
+#ifdef CONFIG_MXC_NAND_HWECC
+static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+ /*
+ * If HW ECC is enabled, we turn it on during init. There is
+ * no need to enable again here.
+ */
}
+#ifdef MXC_NFC_V2_1
static int mxc_nand_read_oob_syndrome(struct mtd_info *mtd,
struct nand_chip *chip,
int page, int sndcmd)
size = mtd->oobsize - (oob - chip->oob_poi);
if (size)
chip->read_buf(mtd, oob, size);
- _mxc_nand_enable_hwecc(mtd, 0);
+ _mxc_nand_enable_hwecc(mtd, 1);
return 0;
}
{
struct nand_chip *nand_chip = mtd->priv;
struct mxc_nand_host *host = nand_chip->priv;
- uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+ uint32_t ecc_status = readl(&host->regs->ecc_status_result);
int subpages = mtd->writesize / nand_chip->subpagesize;
int pg2blk_shift = nand_chip->phys_erase_shift -
nand_chip->page_shift;
#define mxc_nand_write_page_syndrome NULL
#define mxc_nand_write_page_raw_syndrome NULL
#define mxc_nand_write_oob_syndrome NULL
-#define mxc_nfc_11_nand_correct_data NULL
static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
u_char *read_ecc, u_char *calc_ecc)
* additional correction. 2-Bit errors cannot be corrected by
* HW ECC, so we need to return failure
*/
- uint16_t ecc_status = readw(&host->regs->nfc_ecc_status_result);
+ uint16_t ecc_status = readnfc(&host->regs->ecc_status_result);
if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
MTDDEBUG(MTD_DEBUG_LEVEL0,
case NAND_CMD_PAGEPROG:
send_prog_page(host, 0, host->spare_only);
- if (host->pagesize_2k && !is_mxc_nfc_11()) {
+ if (host->pagesize_2k && is_mxc_nfc_1()) {
/* data in 4 areas */
send_prog_page(host, 1, host->spare_only);
send_prog_page(host, 2, host->spare_only);
send_cmd(host, NAND_CMD_READSTART);
/* read for each AREA */
send_read_page(host, 0, host->spare_only);
- if (!is_mxc_nfc_11()) {
+ if (is_mxc_nfc_1()) {
send_read_page(host, 1, host->spare_only);
send_read_page(host, 2, host->spare_only);
send_read_page(host, 3, host->spare_only);
}
}
-#ifdef MXC_NFC_V1_1
-static void mxc_setup_config1(void)
-{
- uint16_t tmp;
-
- tmp = readw(&host->regs->nfc_config1);
- tmp |= NFC_ONE_CYCLE;
- tmp |= NFC_4_8N_ECC;
- writew(tmp, &host->regs->nfc_config1);
- if (host->pagesize_2k)
- writew(64/2, &host->regs->nfc_spare_area_size);
- else
- writew(16/2, &host->regs->nfc_spare_area_size);
-}
-#else
-#define mxc_setup_config1()
-#endif
-
#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
int board_nand_init(struct nand_chip *this)
{
struct mtd_info *mtd;
+#ifdef MXC_NFC_V2_1
uint16_t tmp;
- int err = 0;
+#endif
#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
this->options |= NAND_USE_FLASH_BBT;
this->read_buf = mxc_nand_read_buf;
this->verify_buf = mxc_nand_verify_buf;
- host->regs = (struct nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
+ host->regs = (struct fsl_nfc_regs __iomem *)CONFIG_MXC_NAND_REGS_BASE;
host->clk_act = 1;
#ifdef CONFIG_MXC_NAND_HWECC
this->ecc.calculate = mxc_nand_calculate_ecc;
this->ecc.hwctl = mxc_nand_enable_hwecc;
this->ecc.correct = mxc_nand_correct_data;
- if (is_mxc_nfc_11()) {
+ if (is_mxc_nfc_21()) {
this->ecc.mode = NAND_ECC_HW_SYNDROME;
this->ecc.read_page = mxc_nand_read_page_syndrome;
this->ecc.read_page_raw = mxc_nand_read_page_raw_syndrome;
host->pagesize_2k = 0;
this->ecc.size = 512;
- tmp = readw(&host->regs->nfc_config1);
- tmp |= NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ _mxc_nand_enable_hwecc(mtd, 1);
#else
this->ecc.layout = &nand_soft_eccoob;
this->ecc.mode = NAND_ECC_SOFT;
- tmp = readw(&host->regs->nfc_config1);
- tmp &= ~NFC_ECC_EN;
- writew(tmp, &host->regs->nfc_config1);
+ _mxc_nand_enable_hwecc(mtd, 0);
#endif
/* Reset NAND */
this->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ /* NAND bus width determines access functions used by upper layer */
+ if (is_16bit_nand())
+ this->options |= NAND_BUSWIDTH_16;
+
+#ifdef CONFIG_SYS_NAND_LARGEPAGE
+ host->pagesize_2k = 1;
+ this->ecc.layout = &nand_hw_eccoob2k;
+#else
+ host->pagesize_2k = 0;
+ this->ecc.layout = &nand_hw_eccoob;
+#endif
+
+#ifdef MXC_NFC_V2_1
+ tmp = readnfc(&host->regs->config1);
+ tmp |= NFC_V2_CONFIG1_ONE_CYCLE;
+ tmp |= NFC_V2_CONFIG1_ECC_MODE_4;
+ writenfc(tmp, &host->regs->config1);
+ if (host->pagesize_2k)
+ writenfc(64/2, &host->regs->spare_area_size);
+ else
+ writenfc(16/2, &host->regs->spare_area_size);
+#endif
+
/*
* preset operation
* Unlock the internal RAM Buffer
*/
- writew(0x2, &host->regs->nfc_config);
+ writenfc(0x2, &host->regs->config);
/* Blocks to be unlocked */
- writew(0x0, &host->regs->nfc_unlockstart_blkaddr);
+ writenfc(0x0, &host->regs->unlockstart_blkaddr);
/* Originally (Freescale LTIB 2.6.21) 0x4000 was written to the
* unlockend_blkaddr, but the magic 0x4000 does not always work
* when writing more than some 32 megabytes (on 2k page nands)
* This might be NAND chip specific and the i.MX31 datasheet is
* extremely vague about the semantics of this register.
*/
- writew(0xFFFF, &host->regs->nfc_unlockend_blkaddr);
+ writenfc(0xFFFF, &host->regs->unlockend_blkaddr);
/* Unlock Block Command for given address range */
- writew(0x4, &host->regs->nfc_wrprot);
-
- /* NAND bus width determines access functions used by upper layer */
- if (is_16bit_nand())
- this->options |= NAND_BUSWIDTH_16;
+ writenfc(0x4, &host->regs->wrprot);
-#ifdef CONFIG_SYS_NAND_LARGEPAGE
- host->pagesize_2k = 1;
- this->ecc.layout = &nand_hw_eccoob2k;
-#else
- host->pagesize_2k = 0;
- this->ecc.layout = &nand_hw_eccoob;
-#endif
- mxc_setup_config1();
- return err;
+ return 0;
}