+config MTD_NAND_CORE
+ tristate
-menuconfig NAND
- bool "NAND Device Support"
-if NAND
+source "drivers/mtd/nand/raw/Kconfig"
-config SYS_NAND_SELF_INIT
- bool
- help
- This option, if enabled, provides more flexible and linux-like
- NAND initialization process.
-
-config NAND_DENALI
- bool "Support Denali NAND controller"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- Enable support for the Denali NAND controller.
-
-config NAND_DENALI_DT
- bool "Support Denali NAND controller as a DT device"
- depends on NAND_DENALI && OF_CONTROL && DM
- help
- Enable the driver for NAND flash on platforms using a Denali NAND
- controller as a DT device.
-
-config SYS_NAND_DENALI_64BIT
- bool "Use 64-bit variant of Denali NAND controller"
- depends on NAND_DENALI
- help
- The Denali NAND controller IP has some variations in terms of
- the bus interface. The DMA setup sequence is completely differenct
- between 32bit / 64bit AXI bus variants.
-
- If your Denali NAND controller is the 64-bit variant, say Y.
- Otherwise (32 bit), say N.
-
-config NAND_DENALI_SPARE_AREA_SKIP_BYTES
- int "Number of bytes skipped in OOB area"
- depends on NAND_DENALI
- range 0 63
- help
- This option specifies the number of bytes to skip from the beginning
- of OOB area before last ECC sector data starts. This is potentially
- used to preserve the bad block marker in the OOB area.
-
-config NAND_OMAP_GPMC
- bool "Support OMAP GPMC NAND controller"
- depends on ARCH_OMAP2PLUS
- help
- Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
- GPMC controller is used for parallel NAND flash devices, and can
- do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
- and BCH16 ECC algorithms.
-
-config NAND_OMAP_GPMC_PREFETCH
- bool "Enable GPMC Prefetch"
- depends on NAND_OMAP_GPMC
- help
- On OMAP platforms that use the GPMC controller
- (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
- uses the prefetch mode to speed up read operations.
-
-config NAND_OMAP_ELM
- bool "Enable ELM driver for OMAPxx and AMxx platforms."
- depends on NAND_OMAP_GPMC && !OMAP34XX
- help
- ELM controller is used for ECC error detection (not ECC calculation)
- of BCH4, BCH8 and BCH16 ECC algorithms.
- Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
- thus such SoC platforms need to depend on software library for ECC error
- detection. However ECC calculation on such plaforms would still be
- done by GPMC controller.
-
-config NAND_VF610_NFC
- bool "Support for Freescale NFC for VF610"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- Enables support for NAND Flash Controller on some Freescale
- processors like the VF610, MCF54418 or Kinetis K70.
- The driver supports a maximum 2k page size. The driver
- currently does not support hardware ECC.
-
-choice
- prompt "Hardware ECC strength"
- depends on NAND_VF610_NFC
- default SYS_NAND_VF610_NFC_45_ECC_BYTES
- help
- Select the ECC strength used in the hardware BCH ECC block.
-
-config SYS_NAND_VF610_NFC_45_ECC_BYTES
- bool "24-error correction (45 ECC bytes)"
-
-config SYS_NAND_VF610_NFC_60_ECC_BYTES
- bool "32-error correction (60 ECC bytes)"
-
-endchoice
-
-config NAND_PXA3XX
- bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- This enables the driver for the NAND flash device found on
- PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
-
-config NAND_SUNXI
- bool "Support for NAND on Allwinner SoCs"
- depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
- select SYS_NAND_SELF_INIT
- select SYS_NAND_U_BOOT_LOCATIONS
- imply CMD_NAND
- ---help---
- Enable support for NAND. This option enables the standard and
- SPL drivers.
- The SPL driver only supports reading from the NAND using DMA
- transfers.
-
-if NAND_SUNXI
-
-config NAND_SUNXI_SPL_ECC_STRENGTH
- int "Allwinner NAND SPL ECC Strength"
- default 64
-
-config NAND_SUNXI_SPL_ECC_SIZE
- int "Allwinner NAND SPL ECC Step Size"
- default 1024
-
-config NAND_SUNXI_SPL_USABLE_PAGE_SIZE
- int "Allwinner NAND SPL Usable Page Size"
- default 1024
-
-endif
-
-config NAND_ARASAN
- bool "Configure Arasan Nand"
- imply CMD_NAND
- help
- This enables Nand driver support for Arasan nand flash
- controller. This uses the hardware ECC for read and
- write operations.
-
-config NAND_MXC
- bool "MXC NAND support"
- depends on CPU_ARM926EJS || CPU_ARM1136 || MX5
- imply CMD_NAND
- help
- This enables the NAND driver for the NAND flash controller on the
- i.MX27 / i.MX31 / i.MX5 rocessors.
-
-config NAND_MXS
- bool "MXS NAND support"
- depends on MX6 || MX7
- imply CMD_NAND
- help
- This enables NAND driver for the NAND flash controller on the
- MXS processors.
-
-config NAND_ZYNQ
- bool "Support for Zynq Nand controller"
- select SYS_NAND_SELF_INIT
- imply CMD_NAND
- help
- This enables Nand driver support for Nand flash controller
- found on Zynq SoC.
-
-comment "Generic NAND options"
-
-# Enhance depends when converting drivers to Kconfig which use this config
-# option (mxc_nand, ndfc, omap_gpmc).
-config SYS_NAND_BUSWIDTH_16BIT
- bool "Use 16-bit NAND interface"
- depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI
- help
- Indicates that NAND device has 16-bit wide data-bus. In absence of this
- config, bus-width of NAND device is assumed to be either 8-bit and later
- determined by reading ONFI params.
- Above config is useful when NAND device's bus-width information cannot
- be determined from on-chip ONFI params, like in following scenarios:
- - SPL boot does not support reading of ONFI parameters. This is done to
- keep SPL code foot-print small.
- - In current U-Boot flow using nand_init(), driver initialization
- happens in board_nand_init() which is called before any device probe
- (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
- not available while configuring controller. So a static CONFIG_NAND_xx
- is needed to know the device's bus-width in advance.
-
-if SPL
-
-config SYS_NAND_U_BOOT_LOCATIONS
- bool "Define U-boot binaries locations in NAND"
- help
- Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
- This option should not be enabled when compiling U-boot for boards
- defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
- file.
-
-config SYS_NAND_U_BOOT_OFFS
- hex "Location in NAND to read U-Boot from"
- default 0x800000 if NAND_SUNXI
- depends on SYS_NAND_U_BOOT_LOCATIONS
- help
- Set the offset from the start of the nand where u-boot should be
- loaded from.
-
-config SYS_NAND_U_BOOT_OFFS_REDUND
- hex "Location in NAND to read U-Boot from"
- default SYS_NAND_U_BOOT_OFFS
- depends on SYS_NAND_U_BOOT_LOCATIONS
- help
- Set the offset from the start of the nand where the redundant u-boot
- should be loaded from.
-
-config SPL_NAND_AM33XX_BCH
- bool "Enables SPL-NAND driver which supports ELM based"
- depends on NAND_OMAP_GPMC && !OMAP34XX
- default y
- help
- Hardware ECC correction. This is useful for platforms which have ELM
- hardware engine and use NAND boot mode.
- Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
- so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
- SPL-NAND driver with software ECC correction support.
-
-config SPL_NAND_DENALI
- bool "Support Denali NAND controller for SPL"
- help
- This is a small implementation of the Denali NAND controller
- for use on SPL.
-
-config SPL_NAND_SIMPLE
- bool "Use simple SPL NAND driver"
- depends on !SPL_NAND_AM33XX_BCH
- help
- Support for NAND boot using simple NAND drivers that
- expose the cmd_ctrl() interface.
-endif
-
-endif # if NAND
+source "drivers/mtd/nand/spi/Kconfig"