[MMC_HS_52] = "MMC High Speed (52MHz)",
[MMC_DDR_52] = "MMC DDR52 (52MHz)",
[MMC_HS_200] = "HS200 (200MHz)",
+ [MMC_HS_400] = "HS400 (200MHz)",
};
if (mode >= MMC_MODES_END)
[UHS_DDR50] = 50000000,
[UHS_SDR104] = 208000000,
[MMC_HS_200] = 200000000,
+ [MMC_HS_400] = 200000000,
};
if (mode == MMC_LEGACY)
return err;
}
-int mmc_switch(struct mmc *mmc, u8 set, u8 index, u8 value)
+static int __mmc_switch(struct mmc *mmc, u8 set, u8 index, u8 value,
+ bool send_status)
{
struct mmc_cmd cmd;
int timeout = 1000;
while (retries > 0) {
ret = mmc_send_cmd(mmc, &cmd, NULL);
- /* Waiting for the ready status */
- if (!ret) {
- ret = mmc_send_status(mmc, timeout);
- return ret;
+ if (ret) {
+ retries--;
+ continue;
}
- retries--;
+ if (!send_status) {
+ mdelay(50);
+ return 0;
+ }
+
+ /* Waiting for the ready status */
+ return mmc_send_status(mmc, timeout);
}
return ret;
}
+int mmc_switch(struct mmc *mmc, u8 set, u8 index, u8 value)
+{
+ return __mmc_switch(mmc, set, index, value, true);
+}
+
#if !CONFIG_IS_ENABLED(MMC_TINY)
-static int mmc_set_card_speed(struct mmc *mmc, enum bus_mode mode)
+static int mmc_set_card_speed(struct mmc *mmc, enum bus_mode mode,
+ bool hsdowngrade)
{
int err;
int speed_bits;
speed_bits = EXT_CSD_TIMING_HS200;
break;
#endif
+#if CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+ case MMC_HS_400:
+ speed_bits = EXT_CSD_TIMING_HS400;
+ break;
+#endif
case MMC_LEGACY:
speed_bits = EXT_CSD_TIMING_LEGACY;
break;
default:
return -EINVAL;
}
- err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
- speed_bits);
+
+ err = __mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
+ speed_bits, !hsdowngrade);
if (err)
return err;
+#if CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \
+ CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+ /*
+ * In case the eMMC is in HS200/HS400 mode and we are downgrading
+ * to HS mode, the card clock are still running much faster than
+ * the supported HS mode clock, so we can not reliably read out
+ * Extended CSD. Reconfigure the controller to run at HS mode.
+ */
+ if (hsdowngrade) {
+ mmc_select_mode(mmc, MMC_HS);
+ mmc_set_clock(mmc, mmc_mode2freq(mmc, MMC_HS), false);
+ }
+#endif
+
if ((mode == MMC_HS) || (mode == MMC_HS_52)) {
/* Now check to see that it worked */
err = mmc_send_ext_csd(mmc, test_csd);
mmc->card_caps |= MMC_MODE_4BIT | MMC_MODE_8BIT;
- cardtype = ext_csd[EXT_CSD_CARD_TYPE] & 0x3f;
+ cardtype = ext_csd[EXT_CSD_CARD_TYPE];
mmc->cardtype = cardtype;
#if CONFIG_IS_ENABLED(MMC_HS200_SUPPORT)
mmc->card_caps |= MMC_MODE_HS200;
}
#endif
+#if CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+ if (cardtype & (EXT_CSD_CARD_TYPE_HS400_1_2V |
+ EXT_CSD_CARD_TYPE_HS400_1_8V)) {
+ mmc->card_caps |= MMC_MODE_HS400;
+ }
+#endif
if (cardtype & EXT_CSD_CARD_TYPE_52) {
if (cardtype & EXT_CSD_CARD_TYPE_DDR_52)
mmc->card_caps |= MMC_MODE_DDR_52MHz;
ALLOC_CACHE_ALIGN_BUFFER(uint, switch_status, 16);
int speed;
+ /* SD version 1.00 and 1.01 does not support CMD 6 */
+ if (mmc->version == SD_VERSION_1_0)
+ return 0;
+
switch (mode) {
case SD_LEGACY:
speed = UHS_SDR12_BUS_SPEED;
u32 card_mask = 0;
switch (mode) {
+ case MMC_HS_400:
case MMC_HS_200:
- if (mmc->cardtype & EXT_CSD_CARD_TYPE_HS200_1_8V)
+ if (mmc->cardtype & (EXT_CSD_CARD_TYPE_HS200_1_8V |
+ EXT_CSD_CARD_TYPE_HS400_1_8V))
card_mask |= MMC_SIGNAL_VOLTAGE_180;
- if (mmc->cardtype & EXT_CSD_CARD_TYPE_HS200_1_2V)
+ if (mmc->cardtype & (EXT_CSD_CARD_TYPE_HS200_1_2V |
+ EXT_CSD_CARD_TYPE_HS400_1_2V))
card_mask |= MMC_SIGNAL_VOLTAGE_120;
break;
case MMC_DDR_52:
#endif
static const struct mode_width_tuning mmc_modes_by_pref[] = {
+#if CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+ {
+ .mode = MMC_HS_400,
+ .widths = MMC_MODE_8BIT,
+ .tuning = MMC_CMD_SEND_TUNING_BLOCK_HS200
+ },
+#endif
#if CONFIG_IS_ENABLED(MMC_HS200_SUPPORT)
{
.mode = MMC_HS_200,
{MMC_MODE_1BIT, false, EXT_CSD_BUS_WIDTH_1},
};
+#if CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+static int mmc_select_hs400(struct mmc *mmc)
+{
+ int err;
+
+ /* Set timing to HS200 for tuning */
+ err = mmc_set_card_speed(mmc, MMC_HS_200, false);
+ if (err)
+ return err;
+
+ /* configure the bus mode (host) */
+ mmc_select_mode(mmc, MMC_HS_200);
+ mmc_set_clock(mmc, mmc->tran_speed, false);
+
+ /* execute tuning if needed */
+ err = mmc_execute_tuning(mmc, MMC_CMD_SEND_TUNING_BLOCK_HS200);
+ if (err) {
+ debug("tuning failed\n");
+ return err;
+ }
+
+ /* Set back to HS */
+ mmc_set_card_speed(mmc, MMC_HS, false);
+ mmc_set_clock(mmc, mmc_mode2freq(mmc, MMC_HS), false);
+
+ err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_BUS_WIDTH,
+ EXT_CSD_BUS_WIDTH_8 | EXT_CSD_DDR_FLAG);
+ if (err)
+ return err;
+
+ err = mmc_set_card_speed(mmc, MMC_HS_400, false);
+ if (err)
+ return err;
+
+ mmc_select_mode(mmc, MMC_HS_400);
+ err = mmc_set_clock(mmc, mmc->tran_speed, false);
+ if (err)
+ return err;
+
+ return 0;
+}
+#else
+static int mmc_select_hs400(struct mmc *mmc)
+{
+ return -ENOTSUPP;
+}
+#endif
+
#define for_each_supported_width(caps, ddr, ecbv) \
for (ecbv = ext_csd_bus_width;\
ecbv < ext_csd_bus_width + ARRAY_SIZE(ext_csd_bus_width);\
return -ENOTSUPP;
}
- mmc_set_clock(mmc, mmc->legacy_speed, MMC_CLK_ENABLE);
+#if CONFIG_IS_ENABLED(MMC_HS200_SUPPORT) || \
+ CONFIG_IS_ENABLED(MMC_HS400_SUPPORT)
+ /*
+ * In case the eMMC is in HS200/HS400 mode, downgrade to HS mode
+ * before doing anything else, since a transition from either of
+ * the HS200/HS400 mode directly to legacy mode is not supported.
+ */
+ if (mmc->selected_mode == MMC_HS_200 ||
+ mmc->selected_mode == MMC_HS_400)
+ mmc_set_card_speed(mmc, MMC_HS, true);
+ else
+#endif
+ mmc_set_clock(mmc, mmc->legacy_speed, MMC_CLK_ENABLE);
for_each_mmc_mode_by_pref(card_caps, mwt) {
for_each_supported_width(card_caps & mwt->widths,
goto error;
mmc_set_bus_width(mmc, bus_width(ecbw->cap));
- /* configure the bus speed (card) */
- err = mmc_set_card_speed(mmc, mwt->mode);
- if (err)
- goto error;
-
- /*
- * configure the bus width AND the ddr mode (card)
- * The host side will be taken care of in the next step
- */
- if (ecbw->ext_csd_bits & EXT_CSD_DDR_FLAG) {
- err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL,
- EXT_CSD_BUS_WIDTH,
- ecbw->ext_csd_bits);
+ if (mwt->mode == MMC_HS_400) {
+ err = mmc_select_hs400(mmc);
+ if (err) {
+ printf("Select HS400 failed %d\n", err);
+ goto error;
+ }
+ } else {
+ /* configure the bus speed (card) */
+ err = mmc_set_card_speed(mmc, mwt->mode, false);
if (err)
goto error;
- }
- /* configure the bus mode (host) */
- mmc_select_mode(mmc, mwt->mode);
- mmc_set_clock(mmc, mmc->tran_speed, MMC_CLK_ENABLE);
+ /*
+ * configure the bus width AND the ddr mode
+ * (card). The host side will be taken care
+ * of in the next step
+ */
+ if (ecbw->ext_csd_bits & EXT_CSD_DDR_FLAG) {
+ err = mmc_switch(mmc,
+ EXT_CSD_CMD_SET_NORMAL,
+ EXT_CSD_BUS_WIDTH,
+ ecbw->ext_csd_bits);
+ if (err)
+ goto error;
+ }
+
+ /* configure the bus mode (host) */
+ mmc_select_mode(mmc, mwt->mode);
+ mmc_set_clock(mmc, mmc->tran_speed,
+ MMC_CLK_ENABLE);
#ifdef MMC_SUPPORTS_TUNING
- /* execute tuning if needed */
- if (mwt->tuning) {
- err = mmc_execute_tuning(mmc, mwt->tuning);
- if (err) {
- pr_debug("tuning failed\n");
- goto error;
+ /* execute tuning if needed */
+ if (mwt->tuning) {
+ err = mmc_execute_tuning(mmc,
+ mwt->tuning);
+ if (err) {
+ pr_debug("tuning failed\n");
+ goto error;
+ }
}
- }
#endif
+ }
/* do a transfer to check the configuration */
err = mmc_read_and_compare_ext_csd(mmc);
bdesc->product[0] = 0;
bdesc->revision[0] = 0;
#endif
-#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_LIBDISK_SUPPORT)
+
+#if !defined(CONFIG_DM_MMC) && (!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_LIBDISK_SUPPORT))
part_init(bdesc);
#endif
projects / platform / kernel / u-boot.git / blobdiff