#include "sdhci-pltfm.h"
#define SDHCI_ARASAN_VENDOR_REGISTER 0x78
+
+#define SDHCI_ARASAN_ITAPDLY_REGISTER 0xF0F8
+#define SDHCI_ARASAN_OTAPDLY_REGISTER 0xF0FC
+
#define SDHCI_ARASAN_CQE_BASE_ADDR 0x200
#define VENDOR_ENHANCED_STROBE BIT(0)
#define PHY_CLK_TOO_SLOW_HZ 400000
+#define SDHCI_ITAPDLY_CHGWIN 0x200
+#define SDHCI_ITAPDLY_ENABLE 0x100
+#define SDHCI_OTAPDLY_ENABLE 0x40
+
/* Default settings for ZynqMP Clock Phases */
#define ZYNQMP_ICLK_PHASE {0, 63, 63, 0, 63, 0, 0, 183, 54, 0, 0}
#define ZYNQMP_OCLK_PHASE {0, 72, 60, 0, 60, 72, 135, 48, 72, 135, 0}
+#define VERSAL_ICLK_PHASE {0, 132, 132, 0, 132, 0, 0, 162, 90, 0, 0}
+#define VERSAL_OCLK_PHASE {0, 60, 48, 0, 48, 72, 90, 36, 60, 90, 0}
+
/*
* On some SoCs the syscon area has a feature where the upper 16-bits of
* each 32-bit register act as a write mask for the lower 16-bits. This allows
/**
* struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
*
- * It's up to the licensee of the Arsan IP block to make these available
- * somewhere if needed. Presumably these will be scattered somewhere that's
- * accessible via the syscon API.
- *
* @baseclkfreq: Where to find corecfg_baseclkfreq
* @clockmultiplier: Where to find corecfg_clockmultiplier
+ * @support64b: Where to find SUPPORT64B bit
* @hiword_update: If true, use HIWORD_UPDATE to access the syscon
+ *
+ * It's up to the licensee of the Arsan IP block to make these available
+ * somewhere if needed. Presumably these will be scattered somewhere that's
+ * accessible via the syscon API.
*/
struct sdhci_arasan_soc_ctl_map {
struct sdhci_arasan_soc_ctl_field baseclkfreq;
struct sdhci_arasan_soc_ctl_field clockmultiplier;
+ struct sdhci_arasan_soc_ctl_field support64b;
bool hiword_update;
};
/**
- * struct sdhci_arasan_clk_data
+ * struct sdhci_arasan_clk_ops - Clock Operations for Arasan SD controller
+ *
+ * @sdcardclk_ops: The output clock related operations
+ * @sampleclk_ops: The sample clock related operations
+ */
+struct sdhci_arasan_clk_ops {
+ const struct clk_ops *sdcardclk_ops;
+ const struct clk_ops *sampleclk_ops;
+};
+
+/**
+ * struct sdhci_arasan_clk_data - Arasan Controller Clock Data.
+ *
* @sdcardclk_hw: Struct for the clock we might provide to a PHY.
* @sdcardclk: Pointer to normal 'struct clock' for sdcardclk_hw.
* @sampleclk_hw: Struct for the clock we might provide to a PHY.
};
/**
- * struct sdhci_arasan_data
+ * struct sdhci_arasan_data - Arasan Controller Data
+ *
* @host: Pointer to the main SDHCI host structure.
* @clk_ahb: Pointer to the AHB clock
* @phy: Pointer to the generic phy
* @is_phy_on: True if the PHY is on; false if not.
+ * @has_cqe: True if controller has command queuing engine.
* @clk_data: Struct for the Arasan Controller Clock Data.
+ * @clk_ops: Struct for the Arasan Controller Clock Operations.
* @soc_ctl_base: Pointer to regmap for syscon for soc_ctl registers.
* @soc_ctl_map: Map to get offsets into soc_ctl registers.
+ * @quirks: Arasan deviations from spec.
*/
struct sdhci_arasan_data {
struct sdhci_host *host;
bool has_cqe;
struct sdhci_arasan_clk_data clk_data;
+ const struct sdhci_arasan_clk_ops *clk_ops;
struct regmap *soc_ctl_base;
const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
- unsigned int quirks; /* Arasan deviations from spec */
+ unsigned int quirks;
/* Controller does not have CD wired and will not function normally without */
#define SDHCI_ARASAN_QUIRK_FORCE_CDTEST BIT(0)
struct sdhci_arasan_of_data {
const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
const struct sdhci_pltfm_data *pdata;
+ const struct sdhci_arasan_clk_ops *clk_ops;
};
static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
.hiword_update = false,
};
+static const struct sdhci_arasan_soc_ctl_map intel_keembay_soc_ctl_map = {
+ .baseclkfreq = { .reg = 0x0, .width = 8, .shift = 14 },
+ .clockmultiplier = { .reg = 0x4, .width = 8, .shift = 14 },
+ .support64b = { .reg = 0x4, .width = 1, .shift = 24 },
+ .hiword_update = false,
+};
+
/**
* sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
*
+ * @host: The sdhci_host
+ * @fld: The field to write to
+ * @val: The value to write
+ *
* This function allows writing to fields in sdhci_arasan_soc_ctl_map.
* Note that if a field is specified as not available (shift < 0) then
* this function will silently return an error code. It will be noisy
* and print errors for any other (unexpected) errors.
*
- * @host: The sdhci_host
- * @fld: The field to write to
- * @val: The value to write
+ * Return: 0 on success and error value on error
*/
static int sdhci_arasan_syscon_write(struct sdhci_host *host,
const struct sdhci_arasan_soc_ctl_field *fld,
.set_power = sdhci_set_power_and_bus_voltage,
};
-static const struct sdhci_pltfm_data sdhci_arasan_pdata = {
- .ops = &sdhci_arasan_ops,
- .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
- .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
- SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
- SDHCI_QUIRK2_STOP_WITH_TC,
-};
-
-static struct sdhci_arasan_of_data sdhci_arasan_data = {
- .pdata = &sdhci_arasan_pdata,
-};
-
-static const struct sdhci_pltfm_data sdhci_arasan_zynqmp_pdata = {
- .ops = &sdhci_arasan_ops,
- .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
- SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
- SDHCI_QUIRK2_STOP_WITH_TC,
-};
-
-static struct sdhci_arasan_of_data sdhci_arasan_zynqmp_data = {
- .pdata = &sdhci_arasan_zynqmp_pdata,
-};
-
static u32 sdhci_arasan_cqhci_irq(struct sdhci_host *host, u32 intmask)
{
int cmd_error = 0;
SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
};
-static struct sdhci_arasan_of_data sdhci_arasan_rk3399_data = {
- .soc_ctl_map = &rk3399_soc_ctl_map,
- .pdata = &sdhci_arasan_cqe_pdata,
-};
-
-static struct sdhci_arasan_of_data intel_lgm_emmc_data = {
- .soc_ctl_map = &intel_lgm_emmc_soc_ctl_map,
- .pdata = &sdhci_arasan_cqe_pdata,
-};
-
-static struct sdhci_arasan_of_data intel_lgm_sdxc_data = {
- .soc_ctl_map = &intel_lgm_sdxc_soc_ctl_map,
- .pdata = &sdhci_arasan_cqe_pdata,
-};
-
#ifdef CONFIG_PM_SLEEP
/**
* sdhci_arasan_suspend - Suspend method for the driver
* @dev: Address of the device structure
- * Returns 0 on success and error value on error
*
* Put the device in a low power state.
+ *
+ * Return: 0 on success and error value on error
*/
static int sdhci_arasan_suspend(struct device *dev)
{
/**
* sdhci_arasan_resume - Resume method for the driver
* @dev: Address of the device structure
- * Returns 0 on success and error value on error
*
* Resume operation after suspend
+ *
+ * Return: 0 on success and error value on error
*/
static int sdhci_arasan_resume(struct device *dev)
{
static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
sdhci_arasan_resume);
-static const struct of_device_id sdhci_arasan_of_match[] = {
- /* SoC-specific compatible strings w/ soc_ctl_map */
- {
- .compatible = "rockchip,rk3399-sdhci-5.1",
- .data = &sdhci_arasan_rk3399_data,
- },
- {
- .compatible = "intel,lgm-sdhci-5.1-emmc",
- .data = &intel_lgm_emmc_data,
- },
- {
- .compatible = "intel,lgm-sdhci-5.1-sdxc",
- .data = &intel_lgm_sdxc_data,
- },
- /* Generic compatible below here */
- {
- .compatible = "arasan,sdhci-8.9a",
- .data = &sdhci_arasan_data,
- },
- {
- .compatible = "arasan,sdhci-5.1",
- .data = &sdhci_arasan_data,
- },
- {
- .compatible = "arasan,sdhci-4.9a",
- .data = &sdhci_arasan_data,
- },
- {
- .compatible = "xlnx,zynqmp-8.9a",
- .data = &sdhci_arasan_zynqmp_data,
- },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
-
/**
* sdhci_arasan_sdcardclk_recalc_rate - Return the card clock rate
*
+ * @hw: Pointer to the hardware clock structure.
+ * @parent_rate: The parent rate (should be rate of clk_xin).
+ *
* Return the current actual rate of the SD card clock. This can be used
* to communicate with out PHY.
*
- * @hw: Pointer to the hardware clock structure.
- * @parent_rate The parent rate (should be rate of clk_xin).
- * Returns the card clock rate.
+ * Return: The card clock rate.
*/
static unsigned long sdhci_arasan_sdcardclk_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
-
{
struct sdhci_arasan_clk_data *clk_data =
container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw);
/**
* sdhci_arasan_sampleclk_recalc_rate - Return the sampling clock rate
*
+ * @hw: Pointer to the hardware clock structure.
+ * @parent_rate: The parent rate (should be rate of clk_xin).
+ *
* Return the current actual rate of the sampling clock. This can be used
* to communicate with out PHY.
*
- * @hw: Pointer to the hardware clock structure.
- * @parent_rate The parent rate (should be rate of clk_xin).
- * Returns the sample clock rate.
+ * Return: The sample clock rate.
*/
static unsigned long sdhci_arasan_sampleclk_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
-
{
struct sdhci_arasan_clk_data *clk_data =
container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw);
/**
* sdhci_zynqmp_sdcardclk_set_phase - Set the SD Output Clock Tap Delays
*
+ * @hw: Pointer to the hardware clock structure.
+ * @degrees: The clock phase shift between 0 - 359.
+ *
* Set the SD Output Clock Tap Delays for Output path
*
- * @hw: Pointer to the hardware clock structure.
- * @degrees The clock phase shift between 0 - 359.
* Return: 0 on success and error value on error
*/
static int sdhci_zynqmp_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
-
{
struct sdhci_arasan_clk_data *clk_data =
container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw);
/**
* sdhci_zynqmp_sampleclk_set_phase - Set the SD Input Clock Tap Delays
*
+ * @hw: Pointer to the hardware clock structure.
+ * @degrees: The clock phase shift between 0 - 359.
+ *
* Set the SD Input Clock Tap Delays for Input path
*
- * @hw: Pointer to the hardware clock structure.
- * @degrees The clock phase shift between 0 - 359.
* Return: 0 on success and error value on error
*/
static int sdhci_zynqmp_sampleclk_set_phase(struct clk_hw *hw, int degrees)
-
{
struct sdhci_arasan_clk_data *clk_data =
container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw);
.set_phase = sdhci_zynqmp_sampleclk_set_phase,
};
+/**
+ * sdhci_versal_sdcardclk_set_phase - Set the SD Output Clock Tap Delays
+ *
+ * @hw: Pointer to the hardware clock structure.
+ * @degrees: The clock phase shift between 0 - 359.
+ *
+ * Set the SD Output Clock Tap Delays for Output path
+ *
+ * Return: 0 on success and error value on error
+ */
+static int sdhci_versal_sdcardclk_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct sdhci_arasan_clk_data *clk_data =
+ container_of(hw, struct sdhci_arasan_clk_data, sdcardclk_hw);
+ struct sdhci_arasan_data *sdhci_arasan =
+ container_of(clk_data, struct sdhci_arasan_data, clk_data);
+ struct sdhci_host *host = sdhci_arasan->host;
+ u8 tap_delay, tap_max = 0;
+
+ /*
+ * This is applicable for SDHCI_SPEC_300 and above
+ * Versal does not set phase for <=25MHz clock.
+ * If degrees is zero, no need to do anything.
+ */
+ if (host->version < SDHCI_SPEC_300 ||
+ host->timing == MMC_TIMING_LEGACY ||
+ host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+ return 0;
+
+ switch (host->timing) {
+ case MMC_TIMING_MMC_HS:
+ case MMC_TIMING_SD_HS:
+ case MMC_TIMING_UHS_SDR25:
+ case MMC_TIMING_UHS_DDR50:
+ case MMC_TIMING_MMC_DDR52:
+ /* For 50MHz clock, 30 Taps are available */
+ tap_max = 30;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ /* For 100MHz clock, 15 Taps are available */
+ tap_max = 15;
+ break;
+ case MMC_TIMING_UHS_SDR104:
+ case MMC_TIMING_MMC_HS200:
+ /* For 200MHz clock, 8 Taps are available */
+ tap_max = 8;
+ default:
+ break;
+ }
+
+ tap_delay = (degrees * tap_max) / 360;
+
+ /* Set the Clock Phase */
+ if (tap_delay) {
+ u32 regval;
+
+ regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER);
+ regval |= SDHCI_OTAPDLY_ENABLE;
+ sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
+ regval |= tap_delay;
+ sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER);
+ }
+
+ return 0;
+}
+
+static const struct clk_ops versal_sdcardclk_ops = {
+ .recalc_rate = sdhci_arasan_sdcardclk_recalc_rate,
+ .set_phase = sdhci_versal_sdcardclk_set_phase,
+};
+
+/**
+ * sdhci_versal_sampleclk_set_phase - Set the SD Input Clock Tap Delays
+ *
+ * @hw: Pointer to the hardware clock structure.
+ * @degrees: The clock phase shift between 0 - 359.
+ *
+ * Set the SD Input Clock Tap Delays for Input path
+ *
+ * Return: 0 on success and error value on error
+ */
+static int sdhci_versal_sampleclk_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct sdhci_arasan_clk_data *clk_data =
+ container_of(hw, struct sdhci_arasan_clk_data, sampleclk_hw);
+ struct sdhci_arasan_data *sdhci_arasan =
+ container_of(clk_data, struct sdhci_arasan_data, clk_data);
+ struct sdhci_host *host = sdhci_arasan->host;
+ u8 tap_delay, tap_max = 0;
+
+ /*
+ * This is applicable for SDHCI_SPEC_300 and above
+ * Versal does not set phase for <=25MHz clock.
+ * If degrees is zero, no need to do anything.
+ */
+ if (host->version < SDHCI_SPEC_300 ||
+ host->timing == MMC_TIMING_LEGACY ||
+ host->timing == MMC_TIMING_UHS_SDR12 || !degrees)
+ return 0;
+
+ switch (host->timing) {
+ case MMC_TIMING_MMC_HS:
+ case MMC_TIMING_SD_HS:
+ case MMC_TIMING_UHS_SDR25:
+ case MMC_TIMING_UHS_DDR50:
+ case MMC_TIMING_MMC_DDR52:
+ /* For 50MHz clock, 120 Taps are available */
+ tap_max = 120;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ /* For 100MHz clock, 60 Taps are available */
+ tap_max = 60;
+ break;
+ case MMC_TIMING_UHS_SDR104:
+ case MMC_TIMING_MMC_HS200:
+ /* For 200MHz clock, 30 Taps are available */
+ tap_max = 30;
+ default:
+ break;
+ }
+
+ tap_delay = (degrees * tap_max) / 360;
+
+ /* Set the Clock Phase */
+ if (tap_delay) {
+ u32 regval;
+
+ regval = sdhci_readl(host, SDHCI_ARASAN_ITAPDLY_REGISTER);
+ regval |= SDHCI_ITAPDLY_CHGWIN;
+ sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+ regval |= SDHCI_ITAPDLY_ENABLE;
+ sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+ regval |= tap_delay;
+ sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+ regval &= ~SDHCI_ITAPDLY_CHGWIN;
+ sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER);
+ }
+
+ return 0;
+}
+
+static const struct clk_ops versal_sampleclk_ops = {
+ .recalc_rate = sdhci_arasan_sampleclk_recalc_rate,
+ .set_phase = sdhci_versal_sampleclk_set_phase,
+};
+
static void arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 deviceid)
{
u16 clk;
/**
* sdhci_arasan_update_clockmultiplier - Set corecfg_clockmultiplier
*
+ * @host: The sdhci_host
+ * @value: The value to write
+ *
* The corecfg_clockmultiplier is supposed to contain clock multiplier
* value of programmable clock generator.
*
* - The value of corecfg_clockmultiplier should sync with that of corresponding
* value reading from sdhci_capability_register. So this function is called
* once at probe time and never called again.
- *
- * @host: The sdhci_host
*/
static void sdhci_arasan_update_clockmultiplier(struct sdhci_host *host,
u32 value)
/**
* sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
*
+ * @host: The sdhci_host
+ *
* The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin. This
* function can be used to make that happen.
*
* - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
* to achieve lower clock rates. That means that this function is called once
* at probe time and never called again.
- *
- * @host: The sdhci_host
*/
static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
{
/**
* arasan_dt_parse_clk_phases - Read Clock Delay values from DT
*
- * Called at initialization to parse the values of Clock Delays.
- *
* @dev: Pointer to our struct device.
* @clk_data: Pointer to the Clock Data structure
+ *
+ * Called at initialization to parse the values of Clock Delays.
*/
static void arasan_dt_parse_clk_phases(struct device *dev,
struct sdhci_arasan_clk_data *clk_data)
}
}
+ if (of_device_is_compatible(dev->of_node, "xlnx,versal-8.9a")) {
+ iclk_phase = (int [MMC_TIMING_MMC_HS400 + 1]) VERSAL_ICLK_PHASE;
+ oclk_phase = (int [MMC_TIMING_MMC_HS400 + 1]) VERSAL_OCLK_PHASE;
+
+ for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) {
+ clk_data->clk_phase_in[i] = iclk_phase[i];
+ clk_data->clk_phase_out[i] = oclk_phase[i];
+ }
+ }
+
arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_LEGACY,
"clk-phase-legacy");
arasan_dt_read_clk_phase(dev, clk_data, MMC_TIMING_MMC_HS,
"clk-phase-mmc-hs400");
}
+static const struct sdhci_pltfm_data sdhci_arasan_pdata = {
+ .ops = &sdhci_arasan_ops,
+ .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+ SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
+ SDHCI_QUIRK2_STOP_WITH_TC,
+};
+
+static const struct sdhci_arasan_clk_ops arasan_clk_ops = {
+ .sdcardclk_ops = &arasan_sdcardclk_ops,
+ .sampleclk_ops = &arasan_sampleclk_ops,
+};
+
+static struct sdhci_arasan_of_data sdhci_arasan_generic_data = {
+ .pdata = &sdhci_arasan_pdata,
+ .clk_ops = &arasan_clk_ops,
+};
+
+static const struct sdhci_pltfm_data sdhci_keembay_emmc_pdata = {
+ .ops = &sdhci_arasan_cqe_ops,
+ .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_NO_LED |
+ SDHCI_QUIRK_32BIT_DMA_ADDR |
+ SDHCI_QUIRK_32BIT_DMA_SIZE |
+ SDHCI_QUIRK_32BIT_ADMA_SIZE,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+ SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
+ SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 |
+ SDHCI_QUIRK2_STOP_WITH_TC |
+ SDHCI_QUIRK2_BROKEN_64_BIT_DMA,
+};
+
+static const struct sdhci_pltfm_data sdhci_keembay_sd_pdata = {
+ .ops = &sdhci_arasan_ops,
+ .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_NO_LED |
+ SDHCI_QUIRK_32BIT_DMA_ADDR |
+ SDHCI_QUIRK_32BIT_DMA_SIZE |
+ SDHCI_QUIRK_32BIT_ADMA_SIZE,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+ SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
+ SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON |
+ SDHCI_QUIRK2_STOP_WITH_TC |
+ SDHCI_QUIRK2_BROKEN_64_BIT_DMA,
+};
+
+static const struct sdhci_pltfm_data sdhci_keembay_sdio_pdata = {
+ .ops = &sdhci_arasan_ops,
+ .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC |
+ SDHCI_QUIRK_NO_LED |
+ SDHCI_QUIRK_32BIT_DMA_ADDR |
+ SDHCI_QUIRK_32BIT_DMA_SIZE |
+ SDHCI_QUIRK_32BIT_ADMA_SIZE,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+ SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
+ SDHCI_QUIRK2_HOST_OFF_CARD_ON |
+ SDHCI_QUIRK2_BROKEN_64_BIT_DMA,
+};
+
+static struct sdhci_arasan_of_data sdhci_arasan_rk3399_data = {
+ .soc_ctl_map = &rk3399_soc_ctl_map,
+ .pdata = &sdhci_arasan_cqe_pdata,
+ .clk_ops = &arasan_clk_ops,
+};
+
+static struct sdhci_arasan_of_data intel_lgm_emmc_data = {
+ .soc_ctl_map = &intel_lgm_emmc_soc_ctl_map,
+ .pdata = &sdhci_arasan_cqe_pdata,
+ .clk_ops = &arasan_clk_ops,
+};
+
+static struct sdhci_arasan_of_data intel_lgm_sdxc_data = {
+ .soc_ctl_map = &intel_lgm_sdxc_soc_ctl_map,
+ .pdata = &sdhci_arasan_cqe_pdata,
+ .clk_ops = &arasan_clk_ops,
+};
+
+static const struct sdhci_pltfm_data sdhci_arasan_zynqmp_pdata = {
+ .ops = &sdhci_arasan_ops,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
+ SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN |
+ SDHCI_QUIRK2_STOP_WITH_TC,
+};
+
+static const struct sdhci_arasan_clk_ops zynqmp_clk_ops = {
+ .sdcardclk_ops = &zynqmp_sdcardclk_ops,
+ .sampleclk_ops = &zynqmp_sampleclk_ops,
+};
+
+static struct sdhci_arasan_of_data sdhci_arasan_zynqmp_data = {
+ .pdata = &sdhci_arasan_zynqmp_pdata,
+ .clk_ops = &zynqmp_clk_ops,
+};
+
+static const struct sdhci_arasan_clk_ops versal_clk_ops = {
+ .sdcardclk_ops = &versal_sdcardclk_ops,
+ .sampleclk_ops = &versal_sampleclk_ops,
+};
+
+static struct sdhci_arasan_of_data sdhci_arasan_versal_data = {
+ .pdata = &sdhci_arasan_zynqmp_pdata,
+ .clk_ops = &versal_clk_ops,
+};
+
+static struct sdhci_arasan_of_data intel_keembay_emmc_data = {
+ .soc_ctl_map = &intel_keembay_soc_ctl_map,
+ .pdata = &sdhci_keembay_emmc_pdata,
+};
+
+static struct sdhci_arasan_of_data intel_keembay_sd_data = {
+ .soc_ctl_map = &intel_keembay_soc_ctl_map,
+ .pdata = &sdhci_keembay_sd_pdata,
+};
+
+static struct sdhci_arasan_of_data intel_keembay_sdio_data = {
+ .soc_ctl_map = &intel_keembay_soc_ctl_map,
+ .pdata = &sdhci_keembay_sdio_pdata,
+};
+
+static const struct of_device_id sdhci_arasan_of_match[] = {
+ /* SoC-specific compatible strings w/ soc_ctl_map */
+ {
+ .compatible = "rockchip,rk3399-sdhci-5.1",
+ .data = &sdhci_arasan_rk3399_data,
+ },
+ {
+ .compatible = "intel,lgm-sdhci-5.1-emmc",
+ .data = &intel_lgm_emmc_data,
+ },
+ {
+ .compatible = "intel,lgm-sdhci-5.1-sdxc",
+ .data = &intel_lgm_sdxc_data,
+ },
+ {
+ .compatible = "intel,keembay-sdhci-5.1-emmc",
+ .data = &intel_keembay_emmc_data,
+ },
+ {
+ .compatible = "intel,keembay-sdhci-5.1-sd",
+ .data = &intel_keembay_sd_data,
+ },
+ {
+ .compatible = "intel,keembay-sdhci-5.1-sdio",
+ .data = &intel_keembay_sdio_data,
+ },
+ /* Generic compatible below here */
+ {
+ .compatible = "arasan,sdhci-8.9a",
+ .data = &sdhci_arasan_generic_data,
+ },
+ {
+ .compatible = "arasan,sdhci-5.1",
+ .data = &sdhci_arasan_generic_data,
+ },
+ {
+ .compatible = "arasan,sdhci-4.9a",
+ .data = &sdhci_arasan_generic_data,
+ },
+ {
+ .compatible = "xlnx,zynqmp-8.9a",
+ .data = &sdhci_arasan_zynqmp_data,
+ },
+ {
+ .compatible = "xlnx,versal-8.9a",
+ .data = &sdhci_arasan_versal_data,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
+
/**
* sdhci_arasan_register_sdcardclk - Register the sdcardclk for a PHY to use
*
+ * @sdhci_arasan: Our private data structure.
+ * @clk_xin: Pointer to the functional clock
+ * @dev: Pointer to our struct device.
+ *
* Some PHY devices need to know what the actual card clock is. In order for
* them to find out, we'll provide a clock through the common clock framework
* for them to query.
*
- * @sdhci_arasan: Our private data structure.
- * @clk_xin: Pointer to the functional clock
- * @dev: Pointer to our struct device.
- * Returns 0 on success and error value on error
+ * Return: 0 on success and error value on error
*/
static int
sdhci_arasan_register_sdcardclk(struct sdhci_arasan_data *sdhci_arasan,
sdcardclk_init.parent_names = &parent_clk_name;
sdcardclk_init.num_parents = 1;
sdcardclk_init.flags = CLK_GET_RATE_NOCACHE;
- if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a"))
- sdcardclk_init.ops = &zynqmp_sdcardclk_ops;
- else
- sdcardclk_init.ops = &arasan_sdcardclk_ops;
+ sdcardclk_init.ops = sdhci_arasan->clk_ops->sdcardclk_ops;
clk_data->sdcardclk_hw.init = &sdcardclk_init;
clk_data->sdcardclk =
/**
* sdhci_arasan_register_sampleclk - Register the sampleclk for a PHY to use
*
+ * @sdhci_arasan: Our private data structure.
+ * @clk_xin: Pointer to the functional clock
+ * @dev: Pointer to our struct device.
+ *
* Some PHY devices need to know what the actual card clock is. In order for
* them to find out, we'll provide a clock through the common clock framework
* for them to query.
*
- * @sdhci_arasan: Our private data structure.
- * @clk_xin: Pointer to the functional clock
- * @dev: Pointer to our struct device.
- * Returns 0 on success and error value on error
+ * Return: 0 on success and error value on error
*/
static int
sdhci_arasan_register_sampleclk(struct sdhci_arasan_data *sdhci_arasan,
sampleclk_init.parent_names = &parent_clk_name;
sampleclk_init.num_parents = 1;
sampleclk_init.flags = CLK_GET_RATE_NOCACHE;
- if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a"))
- sampleclk_init.ops = &zynqmp_sampleclk_ops;
- else
- sampleclk_init.ops = &arasan_sampleclk_ops;
+ sampleclk_init.ops = sdhci_arasan->clk_ops->sampleclk_ops;
clk_data->sampleclk_hw.init = &sampleclk_init;
clk_data->sampleclk =
/**
* sdhci_arasan_unregister_sdclk - Undoes sdhci_arasan_register_sdclk()
*
+ * @dev: Pointer to our struct device.
+ *
* Should be called any time we're exiting and sdhci_arasan_register_sdclk()
* returned success.
- *
- * @dev: Pointer to our struct device.
*/
static void sdhci_arasan_unregister_sdclk(struct device *dev)
{
}
/**
+ * sdhci_arasan_update_support64b - Set SUPPORT_64B (64-bit System Bus Support)
+ *
+ * This should be set based on the System Address Bus.
+ * 0: the Core supports only 32-bit System Address Bus.
+ * 1: the Core supports 64-bit System Address Bus.
+ *
+ * NOTES:
+ * - For Keem Bay, it is required to clear this bit. Its default value is 1'b1.
+ * Keem Bay does not support 64-bit access.
+ *
+ * @host The sdhci_host
+ */
+static void sdhci_arasan_update_support64b(struct sdhci_host *host, u32 value)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
+ sdhci_arasan->soc_ctl_map;
+
+ /* Having a map is optional */
+ if (!soc_ctl_map)
+ return;
+
+ /* If we have a map, we expect to have a syscon */
+ if (!sdhci_arasan->soc_ctl_base) {
+ pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
+ mmc_hostname(host->mmc));
+ return;
+ }
+
+ sdhci_arasan_syscon_write(host, &soc_ctl_map->support64b, value);
+}
+
+/**
* sdhci_arasan_register_sdclk - Register the sdcardclk for a PHY to use
*
+ * @sdhci_arasan: Our private data structure.
+ * @clk_xin: Pointer to the functional clock
+ * @dev: Pointer to our struct device.
+ *
* Some PHY devices need to know what the actual card clock is. In order for
* them to find out, we'll provide a clock through the common clock framework
* for them to query.
* to create nice clean device tree bindings and later (if needed) we can try
* re-architecting SDHCI if we see some benefit to it.
*
- * @sdhci_arasan: Our private data structure.
- * @clk_xin: Pointer to the functional clock
- * @dev: Pointer to our struct device.
- * Returns 0 on success and error value on error
+ * Return: 0 on success and error value on error
*/
static int sdhci_arasan_register_sdclk(struct sdhci_arasan_data *sdhci_arasan,
struct clk *clk_xin,
sdhci_arasan->host = host;
sdhci_arasan->soc_ctl_map = data->soc_ctl_map;
+ sdhci_arasan->clk_ops = data->clk_ops;
node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
if (node) {
"rockchip,rk3399-sdhci-5.1"))
sdhci_arasan_update_clockmultiplier(host, 0x0);
+ if (of_device_is_compatible(np, "intel,keembay-sdhci-5.1-emmc") ||
+ of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sd") ||
+ of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sdio")) {
+ sdhci_arasan_update_clockmultiplier(host, 0x0);
+ sdhci_arasan_update_support64b(host, 0x0);
+
+ host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
+ }
+
sdhci_arasan_update_baseclkfreq(host);
ret = sdhci_arasan_register_sdclk(sdhci_arasan, clk_xin, &pdev->dev);
projects / platform / kernel / linux-starfive.git / blobdiff