config MMC
bool "MMC/SD/SDIO card support"
default ARM || PPC || SANDBOX
+ select HAVE_BLOCK_DEVICE
help
This selects MultiMediaCard, Secure Digital and Secure
Digital I/O support.
If you want MMC/SD/SDIO support, you should say Y here and
also to your specific host controller driver.
+config MMC_WRITE
+ bool "support for MMC/SD write operations"
+ depends on MMC
+ default y
+ help
+ Enable write access to MMC and SD Cards
+
+config MMC_BROKEN_CD
+ bool "Poll for broken card detection case"
+ help
+ If card detection feature is broken, just poll to detect.
+
config DM_MMC
bool "Enable MMC controllers using Driver Model"
depends on DM
are enabled by default, other may require additionnal flags or are
enabled by the host driver.
+config MMC_HW_PARTITIONING
+ bool "Support for HW partitioning command(eMMC)"
+ default y
+ help
+ This adds a command and an API to do hardware partitioning on eMMC
+ devices.
+
+config SUPPORT_EMMC_RPMB
+ bool "Support eMMC replay protected memory block (RPMB)"
+ imply CMD_MMC_RPMB
+ help
+ Enable support for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
+config MMC_IO_VOLTAGE
+ bool "Support IO voltage configuration"
+ help
+ IO voltage configuration allows selecting the voltage level of the IO
+ lines (not the level of main supply). This is required for UHS
+ support. For eMMC this not mandatory, but not enabling this option may
+ prevent the driver of using the faster modes.
+
+config SPL_MMC_IO_VOLTAGE
+ bool "Support IO voltage configuration in SPL"
+ default n
+ help
+ IO voltage configuration allows selecting the voltage level of the IO
+ lines (not the level of main supply). This is required for UHS
+ support. For eMMC this not mandatory, but not enabling this option may
+ prevent the driver of using the faster modes.
+
+config MMC_UHS_SUPPORT
+ bool "enable UHS support"
+ depends on MMC_IO_VOLTAGE
+ help
+ The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+ cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+ frequency can go up to 208MHz (SDR104)
+
+config SPL_MMC_UHS_SUPPORT
+ bool "enable UHS support in SPL"
+ depends on SPL_MMC_IO_VOLTAGE
+ help
+ The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
+ cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
+ frequency can go up to 208MHz (SDR104)
+
+config MMC_HS400_SUPPORT
+ bool "enable HS400 support"
+ select MMC_HS200_SUPPORT
+ help
+ The HS400 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
+config SPL_MMC_HS400_SUPPORT
+ bool "enable HS400 support in SPL"
+ help
+ The HS400 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
+config MMC_HS200_SUPPORT
+ bool "enable HS200 support"
+ help
+ The HS200 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
+
+config SPL_MMC_HS200_SUPPORT
+ bool "enable HS200 support in SPL"
+ help
+ The HS200 mode is support by some eMMC. The bus frequency is up to
+ 200MHz. This mode requires tuning the IO.
+
config MMC_VERBOSE
bool "Output more information about the MMC"
default y
Enable the output of more information about the card such as the
operating mode.
-config SPL_MMC_VERBOSE
- bool "Output more information about the MMC in SPL"
+config MMC_TRACE
+ bool "MMC debugging"
default n
help
- Enable the output of more information about the card such as the
- operating mode.
+ This is an option for use by developer. Enable MMC core debugging.
+
+ If you need to see the MMC core message, say Y.
config SPL_MMC_TINY
bool "Tiny MMC framework in SPL"
config MMC_MXS
bool "Freescale MXS Multimedia Card Interface support"
+ depends on MX23 || MX28 || MX6 || MX7
+ select APBH_DMA
+ select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
+ select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
help
This selects the Freescale SSP MMC controller found on MXS based
platforms like mx23/28.
If unsure, say N.
+config MMC_OMAP_HS_ADMA
+ bool "ADMA support for OMAP HS MMC"
+ depends on MMC_OMAP_HS && !OMAP34XX
+ default y if !AM33XX
+ help
+ This enables support for the ADMA2 controller (SDA3.00 Part A2 DMA
+ controller). If supported by the hardware, selecting this option will
+ increase performances.
+
config MMC_OMAP36XX_PINS
bool "Enable MMC1 on OMAP36xx/37xx"
depends on OMAP34XX && MMC_OMAP_HS
help
Support for the on-chip SDHI host controller on SuperH/Renesas ARM SoCs platform
+config SH_MMCIF
+ bool "SuperH/Renesas ARM SoCs on-chip MMCIF host controller support"
+ depends on ARCH_RMOBILE || SH
+ help
+ Support for the on-chip MMCIF host controller on SuperH/Renesas ARM SoCs platform
+
config MMC_UNIPHIER
- bool "UniPhier/RCar SD/MMC Host Controller support"
- depends on ARCH_UNIPHIER || ARCH_RMOBILE
+ bool "UniPhier SD/MMC Host Controller support"
+ depends on ARCH_UNIPHIER
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ help
+ This selects support for the Matsushita SD/MMC Host Controller on
+ SocioNext UniPhier SoCs.
+
+config RENESAS_SDHI
+ bool "Renesas R-Car SD/MMC Host Controller support"
+ depends on ARCH_RMOBILE
depends on BLK && DM_MMC
depends on OF_CONTROL
help
This selects support for the Matsushita SD/MMC Host Controller on
- SocioNext UniPhier and Renesas RCar SoCs.
+ Renesas R-Car SoCs.
+
+config MMC_BCM2835
+ bool "BCM2835 family custom SD/MMC Host Controller support"
+ depends on ARCH_BCM283X
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ default y
+ help
+ This selects support for the custom SD host controller in the BCM2835
+ family of devices.
+
+ If you have a BCM2835 platform with SD or MMC devices, say Y here.
+
+ If unsure, say N.
config MMC_SANDBOX
bool "Sandbox MMC support"
If unsure, say N.
+config MMC_SDHCI_BCMSTB
+ tristate "SDHCI support for the BCMSTB SD/MMC Controller"
+ depends on MMC_SDHCI
+ help
+ This selects the Broadcom set-top box SD/MMC controller.
+
+ If you have a BCMSTB platform with SD or MMC devices,
+ say Y here.
+
+ If unsure, say N.
+
config MMC_SDHCI_CADENCE
bool "SDHCI support for the Cadence SD/SDIO/eMMC controller"
depends on BLK && DM_MMC
If unsure, say N.
+config MMC_SDHCI_K3_ARASAN
+ bool "Arasan SDHCI controller for TI's K3 based SoCs"
+ depends on ARCH_K3
+ depends on MMC_SDHCI
+ depends on DM_MMC && OF_CONTROL && BLK
+ help
+ Support for Arasan SDHCI host controller on Texas Instruments'
+ K3 family based SoC platforms
+
config MMC_SDHCI_KONA
bool "SDHCI support on Broadcom KONA platform"
depends on MMC_SDHCI
config MMC_SDHCI_ZYNQ
bool "Arasan SDHCI controller support"
- depends on ARCH_ZYNQ || ARCH_ZYNQMP
+ depends on ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL
depends on DM_MMC && OF_CONTROL && BLK
depends on MMC_SDHCI
help
Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
+config ZYNQ_SDHCI_MAX_FREQ
+ int "Set the maximum frequency of the controller"
+ depends on MMC_SDHCI_ZYNQ
+ help
+ Set the maximum frequency of the controller.
+
+config ZYNQ_SDHCI_MIN_FREQ
+ int "Set the minimum frequency of the controller"
+ depends on MMC_SDHCI_ZYNQ
+ default 0
+ help
+ Set the minimum frequency of the controller.
+
config MMC_SUNXI
bool "Allwinner sunxi SD/MMC Host Controller support"
depends on ARCH_SUNXI && !UART0_PORT_F
bool
depends on MMC_SUNXI
+config MMC_SUNXI_HAS_MODE_SWITCH
+ bool
+ depends on MMC_SUNXI
+
config GENERIC_ATMEL_MCI
bool "Atmel Multimedia Card Interface support"
depends on DM_MMC && BLK && ARCH_AT91
If you have a board based on such a SoC and with a SD/MMC slot,
say Y or M here.
-config MMC_NDS32
- bool "Andestech SD/MMC controller support"
- depends on DM_MMC && OF_CONTROL && BLK && FTSDC010
- help
- This enables support for the Andestech SD/MMM controller, which is
- based on Faraday IP.
-
config FTSDC010
bool "Ftsdc010 SD/MMC controller Support"
help
This SD/MMC controller is present in Andestech SoCs which is based on Faraday IP.
+config FTSDC010_SDIO
+ bool "Support ftsdc010 sdio"
+ default n
+ depends on FTSDC010
+ help
+ This can enable ftsdc010 sdio function.
+
+config MMC_MTK
+ bool "MediaTek SD/MMC Card Interface support"
+ depends on ARCH_MEDIATEK
+ depends on BLK && DM_MMC
+ depends on OF_CONTROL
+ help
+ This selects the MediaTek(R) Secure digital and Multimedia card Interface.
+ If you have a machine with a integrated SD/MMC card reader, say Y or M here.
+ This is needed if support for any SD/SDIO/MMC devices is required.
+ If unsure, say N.
+
endif
config TEGRA124_MMC_DISABLE_EXT_LOOPBACK
TODO(marcel.ziswiler@toradex.com): Move to device tree controlled
approach once proper kernel integration made it mainline.
+config FSL_ESDHC
+ bool "Freescale/NXP eSDHC controller support"
+ help
+ This selects support for the eSDHC (enhanced secure digital host
+ controller) found on numerous Freescale/NXP SoCs.
+
endmenu
config SYS_FSL_ERRATUM_ESDHC111