+// SPDX-License-Identifier: GPL-2.0+
/*
* Driver for the TWSI (i2c) controller found on the Marvell
* orion5x and kirkwood SoC families.
*
* Author: Albert Aribaud <albert.u.boot@aribaud.net>
* Copyright (c) 2010 Albert Aribaud.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
-#include <asm/errno.h>
+#include <log.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
#include <asm/io.h>
+#include <linux/bitops.h>
+#include <linux/compat.h>
#ifdef CONFIG_DM_I2C
#include <dm.h>
#endif
*/
#ifndef CONFIG_DM_I2C
-#if defined(CONFIG_ORION5X)
+#if defined(CONFIG_ARCH_ORION5X)
#include <asm/arch/orion5x.h>
-#elif (defined(CONFIG_KIRKWOOD) || defined(CONFIG_ARCH_MVEBU))
+#elif (defined(CONFIG_ARCH_KIRKWOOD) || defined(CONFIG_ARCH_MVEBU))
#include <asm/arch/soc.h>
-#elif defined(CONFIG_SUNXI)
+#elif defined(CONFIG_ARCH_SUNXI)
#include <asm/arch/i2c.h>
#else
#error Driver mvtwsi not supported by SoC or board
#endif /* CONFIG_DM_I2C */
/*
+ * On SUNXI, we get CONFIG_SYS_TCLK from this include, so we want to
+ * always have it.
+ */
+#if defined(CONFIG_DM_I2C) && defined(CONFIG_ARCH_SUNXI)
+#include <asm/arch/i2c.h>
+#endif
+
+/*
* TWSI register structure
*/
-#ifdef CONFIG_SUNXI
+#ifdef CONFIG_ARCH_SUNXI
struct mvtwsi_registers {
u32 slave_address;
u32 status;
u32 baudrate;
u32 soft_reset;
+ u32 debug; /* Dummy field for build compatibility with mvebu */
};
#else
u32 baudrate; /* When writing */
};
u32 xtnd_slave_addr;
- u32 reserved[2];
+ u32 reserved0[2];
u32 soft_reset;
+ u32 reserved1[27];
+ u32 debug;
};
#endif
u8 slaveadd;
/* The configured I2C speed in Hz */
uint speed;
+ /* The current length of a clock period (depending on speed) */
+ uint tick;
};
#endif /* CONFIG_DM_I2C */
MVTWSI_READ_ACK = 1,
};
-#ifndef CONFIG_DM_I2C
/*
- * MVTWSI controller base
+ * calc_tick() - Calculate the duration of a clock cycle from the I2C speed
+ *
+ * @speed: The speed in Hz to calculate the clock cycle duration for.
+ * @return The duration of a clock cycle in ns.
*/
+inline uint calc_tick(uint speed)
+{
+ /* One tick = the duration of a period at the specified speed in ns (we
+ * add 100 ns to be on the safe side) */
+ return (1000000000u / speed) + 100;
+}
+
+#ifndef CONFIG_DM_I2C
+/*
+ * twsi_get_base() - Get controller register base for specified adapter
+ *
+ * @adap: Adapter to get the register base for.
+ * @return Register base for the specified adapter.
+ */
static struct mvtwsi_registers *twsi_get_base(struct i2c_adapter *adap)
{
switch (adap->hwadapnr) {
}
/*
- * Wait for IFLG to raise, or return 'timeout.' Then, if the status is as
- * expected, return 0 (ok) or 'wrong status' otherwise.
+ * twsi_wait() - Wait for I2C bus interrupt flag and check status, or time out.
+ *
+ * @return Zero if status is as expected, or a non-zero code if either a time
+ * out occurred, or the status was not the expected one.
*/
-static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status)
+static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status,
+ uint tick)
{
int control, status;
int timeout = 1000;
do {
control = readl(&twsi->control);
if (control & MVTWSI_CONTROL_IFLG) {
+ /*
+ * On Armada 38x it seems that the controller works as
+ * if it first set the MVTWSI_CONTROL_IFLAG in the
+ * control register and only after that it changed the
+ * status register.
+ * This sometimes caused weird bugs which only appeared
+ * on selected I2C speeds and even then only sometimes.
+ * We therefore add here a simple ndealy(100), which
+ * seems to fix this weird bug.
+ */
+ ndelay(100);
status = readl(&twsi->status);
if (status == expected_status)
return 0;
MVTWSI_ERROR_WRONG_STATUS,
control, status, expected_status);
}
- udelay(10); /* One clock cycle at 100 kHz */
+ ndelay(tick); /* One clock cycle */
} while (timeout--);
status = readl(&twsi->status);
return mvtwsi_error(MVTWSI_ERROR_TIMEOUT, control, status,
}
/*
- * Assert the START condition, either in a single I2C transaction
- * or inside back-to-back ones (repeated starts).
+ * twsi_start() - Assert a START condition on the bus.
+ *
+ * This function is used in both single I2C transactions and inside
+ * back-to-back transactions (repeated starts).
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @expected_status: The I2C bus status expected to be asserted after the
+ * operation completion.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if status is as expected, or a non-zero code if either a time
+ * out occurred or the status was not the expected one.
*/
-static int twsi_start(struct mvtwsi_registers *twsi, int expected_status)
+static int twsi_start(struct mvtwsi_registers *twsi, int expected_status,
+ uint tick)
{
/* Assert START */
writel(MVTWSI_CONTROL_TWSIEN | MVTWSI_CONTROL_START |
MVTWSI_CONTROL_CLEAR_IFLG, &twsi->control);
/* Wait for controller to process START */
- return twsi_wait(twsi, expected_status);
+ return twsi_wait(twsi, expected_status, tick);
}
/*
- * Send a byte (i2c address or data).
+ * twsi_send() - Send a byte on the I2C bus.
+ *
+ * The byte may be part of an address byte or data.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @byte: The byte to send.
+ * @expected_status: The I2C bus status expected to be asserted after the
+ * operation completion.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if status is as expected, or a non-zero code if either a time
+ * out occurred or the status was not the expected one.
*/
static int twsi_send(struct mvtwsi_registers *twsi, u8 byte,
- int expected_status)
+ int expected_status, uint tick)
{
/* Write byte to data register for sending */
writel(byte, &twsi->data);
writel(MVTWSI_CONTROL_TWSIEN | MVTWSI_CONTROL_CLEAR_IFLG,
&twsi->control);
/* Wait for controller to receive byte, and check ACK */
- return twsi_wait(twsi, expected_status);
+ return twsi_wait(twsi, expected_status, tick);
}
/*
- * Receive a byte.
+ * twsi_recv() - Receive a byte on the I2C bus.
+ *
+ * The static variable mvtwsi_control_flags controls whether we ack or nak.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @byte: The byte to send.
+ * @ack_flag: Flag that determines whether the received byte should
+ * be acknowledged by the controller or not (sent ACK/NAK).
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if status is as expected, or a non-zero code if either a time
+ * out occurred or the status was not the expected one.
*/
-static int twsi_recv(struct mvtwsi_registers *twsi, u8 *byte, int ack_flag)
+static int twsi_recv(struct mvtwsi_registers *twsi, u8 *byte, int ack_flag,
+ uint tick)
{
int expected_status, status, control;
control |= ack_flag == MVTWSI_READ_ACK ? MVTWSI_CONTROL_ACK : 0;
writel(control | MVTWSI_CONTROL_CLEAR_IFLG, &twsi->control);
/* Wait for controller to receive byte, and assert ACK or NAK */
- status = twsi_wait(twsi, expected_status);
+ status = twsi_wait(twsi, expected_status, tick);
/* If we did receive the expected byte, store it */
if (status == 0)
*byte = readl(&twsi->data);
}
/*
- * Assert the STOP condition.
- * This is also used to force the bus back to idle (SDA = SCL = 1).
+ * twsi_stop() - Assert a STOP condition on the bus.
+ *
+ * This function is also used to force the bus back to idle state (SDA =
+ * SCL = 1).
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out
+ * occurred.
*/
-static int twsi_stop(struct mvtwsi_registers *twsi)
+static int twsi_stop(struct mvtwsi_registers *twsi, uint tick)
{
int control, stop_status;
int status = 0;
stop_status = readl(&twsi->status);
if (stop_status == MVTWSI_STATUS_IDLE)
break;
- udelay(10); /* One clock cycle at 100 kHz */
+ ndelay(tick); /* One clock cycle */
} while (timeout--);
control = readl(&twsi->control);
if (stop_status != MVTWSI_STATUS_IDLE)
return status;
}
+/*
+ * twsi_calc_freq() - Compute I2C frequency depending on m and n parameters.
+ *
+ * @n: Parameter 'n' for the frequency calculation algorithm.
+ * @m: Parameter 'm' for the frequency calculation algorithm.
+ * @return The I2C frequency corresponding to the passed m and n parameters.
+ */
static uint twsi_calc_freq(const int n, const int m)
{
-#ifdef CONFIG_SUNXI
+#ifdef CONFIG_ARCH_SUNXI
return CONFIG_SYS_TCLK / (10 * (m + 1) * (1 << n));
#else
return CONFIG_SYS_TCLK / (10 * (m + 1) * (2 << n));
}
/*
- * Reset controller.
- * Controller reset also resets the baud rate and slave address, so
- * they must be re-established afterwards.
+ * twsi_reset() - Reset the I2C controller.
+ *
+ * Resetting the controller also resets the baud rate and slave address, hence
+ * they must be re-established after the reset.
+ *
+ * @twsi: The MVTWSI register structure to use.
*/
static void twsi_reset(struct mvtwsi_registers *twsi)
{
}
/*
- * Sets baud to the highest possible value not exceeding the requested one.
+ * __twsi_i2c_set_bus_speed() - Set the speed of the I2C controller.
+ *
+ * This function sets baud rate to the highest possible value that does not
+ * exceed the requested rate.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @requested_speed: The desired frequency the controller should run at
+ * in Hz.
+ * @return The actual frequency the controller was configured to.
*/
static uint __twsi_i2c_set_bus_speed(struct mvtwsi_registers *twsi,
uint requested_speed)
}
}
writel(baud, &twsi->baudrate);
- return 0;
+
+ /* Wait for controller for one tick */
+#ifdef CONFIG_DM_I2C
+ ndelay(calc_tick(highest_speed));
+#else
+ ndelay(10000);
+#endif
+ return highest_speed;
}
+/*
+ * __twsi_i2c_init() - Initialize the I2C controller.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @speed: The initial frequency the controller should run at
+ * in Hz.
+ * @slaveadd: The I2C address to be set for the I2C master.
+ * @actual_speed: A output parameter that receives the actual frequency
+ * in Hz the controller was set to by the function.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out
+ * occurred.
+ */
static void __twsi_i2c_init(struct mvtwsi_registers *twsi, int speed,
- int slaveadd)
+ int slaveadd, uint *actual_speed)
{
+ uint tmp_speed;
+
/* Reset controller */
twsi_reset(twsi);
/* Set speed */
- __twsi_i2c_set_bus_speed(twsi, speed);
+ tmp_speed = __twsi_i2c_set_bus_speed(twsi, speed);
+ if (actual_speed)
+ *actual_speed = tmp_speed;
/* Set slave address; even though we don't use it */
writel(slaveadd, &twsi->slave_address);
writel(0, &twsi->xtnd_slave_addr);
/* Assert STOP, but don't care for the result */
- (void) twsi_stop(twsi);
+#ifdef CONFIG_DM_I2C
+ (void) twsi_stop(twsi, calc_tick(*actual_speed));
+#else
+ (void) twsi_stop(twsi, 10000);
+#endif
}
/*
- * Begin I2C transaction with expected start status, at given address.
- * Expected address status will derive from direction bit (bit 0) in addr.
+ * i2c_begin() - Start a I2C transaction.
+ *
+ * Begin a I2C transaction with a given expected start status and chip address.
+ * A START is asserted, and the address byte is sent to the I2C controller. The
+ * expected address status will be derived from the direction bit (bit 0) of
+ * the address byte.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @expected_start_status: The I2C status the controller is expected to
+ * assert after the address byte was sent.
+ * @addr: The address byte to be sent.
+ * @tick: The duration of a clock cycle at the current
+ * I2C speed.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out or
+ * unexpected I2C status occurred.
*/
static int i2c_begin(struct mvtwsi_registers *twsi, int expected_start_status,
- u8 addr)
+ u8 addr, uint tick)
{
int status, expected_addr_status;
else /* Writing */
expected_addr_status = MVTWSI_STATUS_ADDR_W_ACK;
/* Assert START */
- status = twsi_start(twsi, expected_start_status);
+ status = twsi_start(twsi, expected_start_status, tick);
/* Send out the address if the start went well */
if (status == 0)
- status = twsi_send(twsi, addr, expected_addr_status);
+ status = twsi_send(twsi, addr, expected_addr_status, tick);
/* Return 0, or the status of the first failure */
return status;
}
/*
- * Begin read, nak data byte, end.
+ * __twsi_i2c_probe_chip() - Probe the given I2C chip address.
+ *
+ * This function begins a I2C read transaction, does a dummy read and NAKs; if
+ * the procedure succeeds, the chip is considered to be present.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @chip: The chip address to probe.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out or
+ * unexpected I2C status occurred.
*/
-static int __twsi_i2c_probe_chip(struct mvtwsi_registers *twsi, uchar chip)
+static int __twsi_i2c_probe_chip(struct mvtwsi_registers *twsi, uchar chip,
+ uint tick)
{
u8 dummy_byte;
int status;
/* Begin i2c read */
- status = i2c_begin(twsi, MVTWSI_STATUS_START, (chip << 1) | 1);
+ status = i2c_begin(twsi, MVTWSI_STATUS_START, (chip << 1) | 1, tick);
/* Dummy read was accepted: receive byte, but NAK it. */
if (status == 0)
- status = twsi_recv(twsi, &dummy_byte, MVTWSI_READ_NAK);
+ status = twsi_recv(twsi, &dummy_byte, MVTWSI_READ_NAK, tick);
/* Stop transaction */
- twsi_stop(twsi);
+ twsi_stop(twsi, tick);
/* Return 0, or the status of the first failure */
return status;
}
/*
- * Begin write, send address byte(s), begin read, receive data bytes, end.
+ * __twsi_i2c_read() - Read data from a I2C chip.
+ *
+ * This function begins a I2C write transaction, and transmits the address
+ * bytes; then begins a I2C read transaction, and receives the data bytes.
*
* NOTE: Some devices want a stop right before the second start, while some
* will choke if it is there. Since deciding this is not yet supported in
* higher level APIs, we need to make a decision here, and for the moment that
* will be a repeated start without a preceding stop.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @chip: The chip address to read from.
+ * @addr: The address bytes to send.
+ * @alen: The length of the address bytes in bytes.
+ * @data: The buffer to receive the data read from the chip (has to have
+ * a size of at least 'length' bytes).
+ * @length: The amount of data to be read from the chip in bytes.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out or
+ * unexpected I2C status occurred.
*/
static int __twsi_i2c_read(struct mvtwsi_registers *twsi, uchar chip,
- u8 *addr, int alen, uchar *data, int length)
+ u8 *addr, int alen, uchar *data, int length,
+ uint tick)
{
int status = 0;
int stop_status;
-
- /* Begin i2c write to send the address bytes */
- status = i2c_begin(twsi, MVTWSI_STATUS_START, (chip << 1));
- /* Send address bytes */
- while ((status == 0) && alen--)
- status = twsi_send(twsi, *(addr++), MVTWSI_STATUS_DATA_W_ACK);
+ int expected_start = MVTWSI_STATUS_START;
+
+ if (alen > 0) {
+ /* Begin i2c write to send the address bytes */
+ status = i2c_begin(twsi, expected_start, (chip << 1), tick);
+ /* Send address bytes */
+ while ((status == 0) && alen--)
+ status = twsi_send(twsi, addr[alen],
+ MVTWSI_STATUS_DATA_W_ACK, tick);
+ /* Send repeated STARTs after the initial START */
+ expected_start = MVTWSI_STATUS_REPEATED_START;
+ }
/* Begin i2c read to receive data bytes */
if (status == 0)
- status = i2c_begin(twsi, MVTWSI_STATUS_REPEATED_START,
- (chip << 1) | 1);
+ status = i2c_begin(twsi, expected_start, (chip << 1) | 1, tick);
/* Receive actual data bytes; set NAK if we if we have nothing more to
* read */
while ((status == 0) && length--)
status = twsi_recv(twsi, data++,
length > 0 ?
- MVTWSI_READ_ACK : MVTWSI_READ_NAK);
+ MVTWSI_READ_ACK : MVTWSI_READ_NAK, tick);
/* Stop transaction */
- stop_status = twsi_stop(twsi);
+ stop_status = twsi_stop(twsi, tick);
/* Return 0, or the status of the first failure */
return status != 0 ? status : stop_status;
}
/*
- * Begin write, send address byte(s), send data bytes, end.
+ * __twsi_i2c_write() - Send data to a I2C chip.
+ *
+ * This function begins a I2C write transaction, and transmits the address
+ * bytes; then begins a new I2C write transaction, and sends the data bytes.
+ *
+ * @twsi: The MVTWSI register structure to use.
+ * @chip: The chip address to read from.
+ * @addr: The address bytes to send.
+ * @alen: The length of the address bytes in bytes.
+ * @data: The buffer containing the data to be sent to the chip.
+ * @length: The length of data to be sent to the chip in bytes.
+ * @tick: The duration of a clock cycle at the current I2C speed.
+ * @return Zero if the operation succeeded, or a non-zero code if a time out or
+ * unexpected I2C status occurred.
*/
static int __twsi_i2c_write(struct mvtwsi_registers *twsi, uchar chip,
- u8 *addr, int alen, uchar *data, int length)
+ u8 *addr, int alen, uchar *data, int length,
+ uint tick)
{
int status, stop_status;
/* Begin i2c write to send first the address bytes, then the
* data bytes */
- status = i2c_begin(twsi, MVTWSI_STATUS_START, (chip << 1));
+ status = i2c_begin(twsi, MVTWSI_STATUS_START, (chip << 1), tick);
/* Send address bytes */
while ((status == 0) && (alen-- > 0))
- status = twsi_send(twsi, *(addr++), MVTWSI_STATUS_DATA_W_ACK);
+ status = twsi_send(twsi, addr[alen], MVTWSI_STATUS_DATA_W_ACK,
+ tick);
/* Send data bytes */
while ((status == 0) && (length-- > 0))
- status = twsi_send(twsi, *(data++), MVTWSI_STATUS_DATA_W_ACK);
+ status = twsi_send(twsi, *(data++), MVTWSI_STATUS_DATA_W_ACK,
+ tick);
/* Stop transaction */
- stop_status = twsi_stop(twsi);
+ stop_status = twsi_stop(twsi, tick);
/* Return 0, or the status of the first failure */
return status != 0 ? status : stop_status;
}
int slaveadd)
{
struct mvtwsi_registers *twsi = twsi_get_base(adap);
- __twsi_i2c_init(twsi, speed, slaveadd);
+ __twsi_i2c_init(twsi, speed, slaveadd, NULL);
}
static uint twsi_i2c_set_bus_speed(struct i2c_adapter *adap,
uint requested_speed)
{
struct mvtwsi_registers *twsi = twsi_get_base(adap);
- return __twsi_i2c_set_bus_speed(twsi, requested_speed);
+ __twsi_i2c_set_bus_speed(twsi, requested_speed);
+ return 0;
}
static int twsi_i2c_probe(struct i2c_adapter *adap, uchar chip)
{
struct mvtwsi_registers *twsi = twsi_get_base(adap);
- return __twsi_i2c_probe_chip(twsi, chip);
+ return __twsi_i2c_probe_chip(twsi, chip, 10000);
}
static int twsi_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
addr_bytes[2] = (addr >> 16) & 0xFF;
addr_bytes[3] = (addr >> 24) & 0xFF;
- return __twsi_i2c_read(twsi, chip, addr_bytes, alen, data, length);
+ return __twsi_i2c_read(twsi, chip, addr_bytes, alen, data, length,
+ 10000);
}
static int twsi_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
addr_bytes[2] = (addr >> 16) & 0xFF;
addr_bytes[3] = (addr >> 24) & 0xFF;
- return __twsi_i2c_write(twsi, chip, addr_bytes, alen, data, length);
+ return __twsi_i2c_write(twsi, chip, addr_bytes, alen, data, length,
+ 10000);
}
#ifdef CONFIG_I2C_MVTWSI_BASE0
u32 chip_flags)
{
struct mvtwsi_i2c_dev *dev = dev_get_priv(bus);
- return __twsi_i2c_probe_chip(dev->base, chip_addr);
+ return __twsi_i2c_probe_chip(dev->base, chip_addr, dev->tick);
}
static int mvtwsi_i2c_set_bus_speed(struct udevice *bus, uint speed)
{
struct mvtwsi_i2c_dev *dev = dev_get_priv(bus);
- return __twsi_i2c_set_bus_speed(dev->base, speed);
+
+ dev->speed = __twsi_i2c_set_bus_speed(dev->base, speed);
+ dev->tick = calc_tick(dev->speed);
+
+ return 0;
}
static int mvtwsi_i2c_ofdata_to_platdata(struct udevice *bus)
{
struct mvtwsi_i2c_dev *dev = dev_get_priv(bus);
- dev->base = dev_get_addr_ptr(bus);
+ dev->base = dev_read_addr_ptr(bus);
if (!dev->base)
return -ENOMEM;
- dev->index = fdtdec_get_int(gd->fdt_blob, bus->of_offset,
+ dev->index = fdtdec_get_int(gd->fdt_blob, dev_of_offset(bus),
"cell-index", -1);
- dev->slaveadd = fdtdec_get_int(gd->fdt_blob, bus->of_offset,
+ dev->slaveadd = fdtdec_get_int(gd->fdt_blob, dev_of_offset(bus),
"u-boot,i2c-slave-addr", 0x0);
- dev->speed = fdtdec_get_int(gd->fdt_blob, bus->of_offset,
- "clock-frequency", 100000);
+ dev->speed = dev_read_u32_default(bus, "clock-frequency",
+ I2C_SPEED_STANDARD_RATE);
+
+ return 0;
+}
+
+static void twsi_disable_i2c_slave(struct mvtwsi_registers *twsi)
+{
+ clrbits_le32(&twsi->debug, BIT(18));
+}
+
+static int mvtwsi_i2c_bind(struct udevice *bus)
+{
+ struct mvtwsi_registers *twsi = dev_read_addr_ptr(bus);
+
+ /* Disable the hidden slave in i2c0 of these platforms */
+ if ((IS_ENABLED(CONFIG_ARMADA_38X) || IS_ENABLED(CONFIG_ARCH_KIRKWOOD))
+ && bus->req_seq == 0)
+ twsi_disable_i2c_slave(twsi);
+
return 0;
}
static int mvtwsi_i2c_probe(struct udevice *bus)
{
struct mvtwsi_i2c_dev *dev = dev_get_priv(bus);
- __twsi_i2c_init(dev->base, dev->speed, dev->slaveadd);
+ uint actual_speed;
+
+ __twsi_i2c_init(dev->base, dev->speed, dev->slaveadd, &actual_speed);
+ dev->speed = actual_speed;
+ dev->tick = calc_tick(dev->speed);
return 0;
}
if (dmsg->flags & I2C_M_RD)
return __twsi_i2c_read(dev->base, dmsg->addr, omsg->buf,
- omsg->len, dmsg->buf, dmsg->len);
+ omsg->len, dmsg->buf, dmsg->len,
+ dev->tick);
else
return __twsi_i2c_write(dev->base, dmsg->addr, omsg->buf,
- omsg->len, dmsg->buf, dmsg->len);
+ omsg->len, dmsg->buf, dmsg->len,
+ dev->tick);
}
static const struct dm_i2c_ops mvtwsi_i2c_ops = {
static const struct udevice_id mvtwsi_i2c_ids[] = {
{ .compatible = "marvell,mv64xxx-i2c", },
+ { .compatible = "marvell,mv78230-i2c", },
+ { .compatible = "allwinner,sun6i-a31-i2c", },
{ /* sentinel */ }
};
.name = "i2c_mvtwsi",
.id = UCLASS_I2C,
.of_match = mvtwsi_i2c_ids,
+ .bind = mvtwsi_i2c_bind,
.probe = mvtwsi_i2c_probe,
.ofdata_to_platdata = mvtwsi_i2c_ofdata_to_platdata,
.priv_auto_alloc_size = sizeof(struct mvtwsi_i2c_dev),