Say yes here to select Cadence I2C Host Controller. This controller is
e.g. used by Xilinx Zynq.
+config SYS_I2C_DAVINCI
+ bool "Davinci I2C Controller"
+ depends on (ARCH_KEYSTONE || ARCH_DAVINCI)
+ help
+ Say yes here to add support for Davinci and Keystone I2C controller
+
config SYS_I2C_DW
bool "Designware I2C Controller"
default n
help
Add support for the NXP i.MX LPI2C driver.
+config SYS_I2C_MESON
+ bool "Amlogic Meson I2C driver"
+ depends on DM_I2C && ARCH_MESON
+ help
+ Add support for the I2C controller available in Amlogic Meson
+ SoCs. The controller supports programmable bus speed including
+ standard (100kbits/s) and fast (400kbit/s) speed and allows the
+ software to define a flexible format of the bit streams. It has an
+ internal buffer holding up to 8 bytes for transfers and supports
+ both 7-bit and 10-bit addresses.
+
config SYS_I2C_MXC
- bool "NXP i.MX I2C driver"
- depends on MX6
+ bool "NXP MXC I2C driver"
+ help
+ Add support for the NXP I2C driver. This supports up to four bus
+ channels and operating on standard mode up to 100 kbits/s and fast
+ mode up to 400 kbits/s.
+
+# These settings are not used with DM_I2C, however SPL doesn't use
+# DM_I2C even if DM_I2C is enabled, and so might use these settings even
+# when main u-boot does not!
+if SYS_I2C_MXC && (!DM_I2C || SPL)
+config SYS_I2C_MXC_I2C1
+ bool "NXP MXC I2C1"
+ help
+ Add support for NXP MXC I2C Controller 1.
+ Required for SoCs which have I2C MXC controller 1 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C2
+ bool "NXP MXC I2C2"
+ help
+ Add support for NXP MXC I2C Controller 2.
+ Required for SoCs which have I2C MXC controller 2 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C3
+ bool "NXP MXC I2C3"
+ help
+ Add support for NXP MXC I2C Controller 3.
+ Required for SoCs which have I2C MXC controller 3 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C4
+ bool "NXP MXC I2C4"
+ help
+ Add support for NXP MXC I2C Controller 4.
+ Required for SoCs which have I2C MXC controller 4 eg LS1088A, LS2080A
+
+config SYS_I2C_MXC_I2C5
+ bool "NXP MXC I2C5"
+ help
+ Add support for NXP MXC I2C Controller 5.
+ Required for SoCs which have I2C MXC controller 5 eg LX2160A
+
+config SYS_I2C_MXC_I2C6
+ bool "NXP MXC I2C6"
+ help
+ Add support for NXP MXC I2C Controller 6.
+ Required for SoCs which have I2C MXC controller 6 eg LX2160A
+
+config SYS_I2C_MXC_I2C7
+ bool "NXP MXC I2C7"
+ help
+ Add support for NXP MXC I2C Controller 7.
+ Required for SoCs which have I2C MXC controller 7 eg LX2160A
+
+config SYS_I2C_MXC_I2C8
+ bool "NXP MXC I2C8"
+ help
+ Add support for NXP MXC I2C Controller 8.
+ Required for SoCs which have I2C MXC controller 8 eg LX2160A
+endif
+
+if SYS_I2C_MXC_I2C1
+config SYS_MXC_I2C1_SPEED
+ int "I2C Channel 1 speed"
+ default 40000000 if TARGET_LS2080A_SIMU || TARGET_LS2080A_EMU
+ default 100000
+ help
+ MXC I2C Channel 1 speed
+
+config SYS_MXC_I2C1_SLAVE
+ int "I2C1 Slave"
+ default 0
+ help
+ MXC I2C1 Slave
+endif
+
+if SYS_I2C_MXC_I2C2
+config SYS_MXC_I2C2_SPEED
+ int "I2C Channel 2 speed"
+ default 40000000 if TARGET_LS2080A_SIMU || TARGET_LS2080A_EMU
+ default 100000
+ help
+ MXC I2C Channel 2 speed
+
+config SYS_MXC_I2C2_SLAVE
+ int "I2C2 Slave"
+ default 0
+ help
+ MXC I2C2 Slave
+endif
+
+if SYS_I2C_MXC_I2C3
+config SYS_MXC_I2C3_SPEED
+ int "I2C Channel 3 speed"
+ default 100000
+ help
+ MXC I2C Channel 3 speed
+
+config SYS_MXC_I2C3_SLAVE
+ int "I2C3 Slave"
+ default 0
+ help
+ MXC I2C3 Slave
+endif
+
+if SYS_I2C_MXC_I2C4
+config SYS_MXC_I2C4_SPEED
+ int "I2C Channel 4 speed"
+ default 100000
help
- Add support for the NXP i.MX I2C driver. This supports upto for bus
- channels and operating on standard mode upto 100 kbits/s and fast
- mode upto 400 kbits/s.
+ MXC I2C Channel 4 speed
+
+config SYS_MXC_I2C4_SLAVE
+ int "I2C4 Slave"
+ default 0
+ help
+ MXC I2C4 Slave
+endif
+
+if SYS_I2C_MXC_I2C5
+config SYS_MXC_I2C5_SPEED
+ int "I2C Channel 5 speed"
+ default 100000
+ help
+ MXC I2C Channel 5 speed
+
+config SYS_MXC_I2C5_SLAVE
+ int "I2C5 Slave"
+ default 0
+ help
+ MXC I2C5 Slave
+endif
+
+if SYS_I2C_MXC_I2C6
+config SYS_MXC_I2C6_SPEED
+ int "I2C Channel 6 speed"
+ default 100000
+ help
+ MXC I2C Channel 6 speed
+
+config SYS_MXC_I2C6_SLAVE
+ int "I2C6 Slave"
+ default 0
+ help
+ MXC I2C6 Slave
+endif
+
+if SYS_I2C_MXC_I2C7
+config SYS_MXC_I2C7_SPEED
+ int "I2C Channel 7 speed"
+ default 100000
+ help
+ MXC I2C Channel 7 speed
+
+config SYS_MXC_I2C7_SLAVE
+ int "I2C7 Slave"
+ default 0
+ help
+ MXC I2C7 Slave
+endif
+
+if SYS_I2C_MXC_I2C8
+config SYS_MXC_I2C8_SPEED
+ int "I2C Channel 8 speed"
+ default 100000
+ help
+ MXC I2C Channel 8 speed
+
+config SYS_MXC_I2C8_SLAVE
+ int "I2C8 Slave"
+ default 0
+ help
+ MXC I2C8 Slave
+endif
config SYS_I2C_OMAP24XX
bool "TI OMAP2+ I2C driver"
help
Add support for the OMAP2+ I2C driver.
+if SYS_I2C_OMAP24XX
+config SYS_OMAP24_I2C_SLAVE
+ int "I2C Slave addr channel 0"
+ default 1
+ help
+ OMAP24xx I2C Slave address channel 0
+
+config SYS_OMAP24_I2C_SPEED
+ int "I2C Slave channel 0 speed"
+ default 100000
+ help
+ OMAP24xx Slave speed channel 0
+endif
+
+config SYS_I2C_RCAR_I2C
+ bool "Renesas RCar I2C driver"
+ depends on (RCAR_GEN3 || RCAR_GEN2) && DM_I2C
+ help
+ Support for Renesas RCar I2C controller.
+
+config SYS_I2C_RCAR_IIC
+ bool "Renesas RCar Gen3 IIC driver"
+ depends on (RCAR_GEN3 || RCAR_GEN2) && DM_I2C
+ help
+ Support for Renesas RCar Gen3 IIC controller.
+
config SYS_I2C_ROCKCHIP
bool "Rockchip I2C driver"
depends on DM_I2C
help
Add support for the Rockchip I2C driver. This is used with various
Rockchip parts such as RK3126, RK3128, RK3036 and RK3288. All chips
- have several I2C ports and all are provided, controled by the
+ have several I2C ports and all are provided, controlled by the
device tree.
config SYS_I2C_SANDBOX
config SYS_I2C_STM32F7
bool "STMicroelectronics STM32F7 I2C support"
- depends on (STM32F7 || STM32H7) && DM_I2C
+ depends on (STM32F7 || STM32H7 || ARCH_STM32MP) && DM_I2C
help
Enable this option to add support for STM32 I2C controller
introduced with STM32F7/H7 SoCs. This I2C controller supports :
_ Optional clock stretching
_ Software reset
+config SYS_I2C_TEGRA
+ bool "NVIDIA Tegra internal I2C controller"
+ depends on TEGRA
+ help
+ Support for NVIDIA I2C controller available in Tegra SoCs.
+
config SYS_I2C_UNIPHIER
bool "UniPhier I2C driver"
depends on ARCH_UNIPHIER && DM_I2C
Support for UniPhier FIFO-builtin I2C controller driver.
This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
+config SYS_I2C_VERSATILE
+ bool "Arm Ltd Versatile I2C bus driver"
+ depends on DM_I2C && (TARGET_VEXPRESS_CA15_TC2 || TARGET_VEXPRESS64_JUNO)
+ help
+ Add support for the Arm Ltd Versatile Express I2C driver. The I2C host
+ controller is present in the development boards manufactured by Arm Ltd.
+
config SYS_I2C_MVTWSI
bool "Marvell I2C driver"
depends on DM_I2C
help
Define the maximum number of available I2C buses.
+config SYS_I2C_XILINX_XIIC
+ bool "Xilinx AXI I2C driver"
+ depends on DM_I2C
+ help
+ Support for Xilinx AXI I2C controller.
+
+config SYS_I2C_IHS
+ bool "gdsys IHS I2C driver"
+ depends on DM_I2C
+ help
+ Support for gdsys IHS I2C driver on FPGA bus.
+
source "drivers/i2c/muxes/Kconfig"
endmenu