# GPIO infrastructure and drivers
#
-menu "GPIO Support"
+menuconfig GPIO
+ bool "GPIO support"
+ default y
+ help
+ Enable support for GPIOs (General-purpose Input/Output) in U-Boot.
+ GPIOs allow U-Boot to read the state of an input line (high or
+ low) and set the state of an output line. This can be used to
+ drive LEDs, control power to various system parts and read user
+ input. GPIOs can be useful to enable a 'sign-of-life' LED,
+ for example. Enable this option to build the drivers in
+ drivers/gpio as part of an U-Boot build.
+
+if GPIO
config DM_GPIO
bool "Enable Driver Model for GPIO drivers"
config GPIO_HOG
bool "Enable GPIO hog support"
depends on DM_GPIO
- default n
help
Enable gpio hog support
The GPIO chip may contain GPIO hog definitions. GPIO hogging
Select this to enable PIO for Altera devices. Please find
details on the "Embedded Peripherals IP User Guide" of Altera.
+config BCM2835_GPIO
+ bool "BCM2835 GPIO driver"
+ depends on DM_GPIO
+
config BCM6345_GPIO
bool "BCM6345 GPIO driver"
depends on DM_GPIO && (ARCH_BMIPS || ARCH_BCM68360 || \
- ARCH_BCM6858 || ARCH_BCM63158)
+ ARCH_BCM6858 || ARCH_BCM63158 || \
+ ARCH_BCM6753)
help
This driver supports the GPIO banks on BCM6345 SoCs.
config DWAPB_GPIO
bool "DWAPB GPIO driver"
depends on DM && DM_GPIO
- default n
help
Support for the Designware APB GPIO driver.
config AT91_GPIO
bool "AT91 PIO GPIO driver"
- default n
help
Say yes here to select AT91 PIO GPIO driver. AT91 PIO
controller manages up to 32 fully programmable input/output
config ATMEL_PIO4
bool "ATMEL PIO4 driver"
depends on DM_GPIO
- default n
help
Say yes here to support the Atmel PIO4 driver.
The PIO4 is new version of Atmel PIO controller, which manages
may be dedicated as a general purpose I/O or be assigned to
a function of an embedded peripheral.
+config ASPEED_GPIO
+ bool "Aspeed GPIO Driver"
+ help
+ Say yes here to support the Aspeed GPIO driver. The controller
+ is found in the AST2400, AST2500 and AST2600 BMC SoCs and
+ provides access to over 200 GPIOs on each chip.
+
config DA8XX_GPIO
bool "DA8xx GPIO Driver"
help
This driver supports the DA8xx GPIO controller
+config FXL6408_GPIO
+ bool "FXL6408 I2C GPIO expander driver"
+ depends on DM_GPIO && DM_I2C
+ help
+ This driver supports the Fairchild FXL6408 device. FXL6408 is a
+ fully configurable 8-bit I2C-controlled GPIO expander.
+
config INTEL_BROADWELL_GPIO
bool "Intel Broadwell GPIO driver"
depends on DM
config IMX_RGPIO2P
bool "i.MX7ULP RGPIO2P driver"
depends on DM
- default n
help
This driver supports i.MX7ULP Rapid GPIO2P controller.
config IPROC_GPIO
bool "Broadcom iProc GPIO driver(without pinconf)"
- default n
help
The Broadcom iProc based SoCs- Cygnus, NS2, NS3, NSP and Stingray,
use the same GPIO Controller IP hence this driver could be used
config HSDK_CREG_GPIO
bool "HSDK CREG GPIO griver"
depends on DM_GPIO
- default n
help
This driver supports CREG GPIOs on Synopsys HSDK SOC.
+config KIRKWOOD_GPIO
+ bool "Kirkwood GPIO driver"
+ help
+ This drdiver supports GPIOs on Kirkwood platforms
+
config LPC32XX_GPIO
bool "LPC32XX GPIO driver"
depends on DM
- default n
help
Support for the LPC32XX GPIO driver.
+config MAX7320_GPIO
+ bool "MAX7320 I2C GPIO Expander driver"
+ depends on DM_GPIO && DM_I2C
+ help
+ Support for MAX7320 I2C 8/16-bit GPIO expander.
+ original maxim device has 8 push/pull outputs,
+ some clones offers 16bit.
+
config MCP230XX_GPIO
bool "MCP230XX GPIO driver"
depends on DM
config MSM_GPIO
bool "Qualcomm GPIO driver"
depends on DM_GPIO
- default n
help
Support GPIO controllers on Qualcomm Snapdragon family of SoCs.
This controller have single bank (default name "soc"), every
config VYBRID_GPIO
bool "Vybrid GPIO driver"
depends on DM
- default n
help
Say yes here to support Vybrid vf610 GPIOs.
config OCTEON_GPIO
bool "Octeon II/III/TX/TX2 GPIO driver"
- depends on DM_GPIO && DM_PCI && (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
+ depends on DM_GPIO && PCI && (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
default y
help
Add support for the Marvell Octeon GPIO driver. This is used with
into a number of banks each with 32 GPIOs. The GPIOs for a device are
defined in the device tree with one node for each bank.
-endmenu
+config ZYNQMP_GPIO_MODEPIN
+ bool "ZynqMP gpio modepin"
+ depends on DM_GPIO
+ help
+ This config enables the ZynqMP gpio modepin driver. ZynqMP modepin
+ driver will set and get the status of PS_MODE pins. These modepins
+ are accessed using xilinx firmware. In modepin register, [3:0] bits
+ set direction, [7:4] bits read IO, [11:8] bits set/clear IO.
+
+config SL28CPLD_GPIO
+ bool "Kontron sl28cpld GPIO driver"
+ depends on DM_GPIO && SL28CPLD
+ help
+ Support GPIO access on Kontron sl28cpld board management controllers.
+
+config SLG7XL45106_I2C_GPO
+ bool "slg7xl45106 i2c gpo expander"
+ depends on DM_GPIO
+ help
+ Support for slg7xl45106 i2c gpo expander. It is an i2c based
+ 8-bit gpo expander, all gpo lines are controlled by writing
+ value into data register.
+
+endif
projects / platform / kernel / u-boot.git / blobdiff