#include <fsl_immap.h>
#include <fsl_ddr.h>
#include <fsl_errata.h>
+#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3) || \
+ defined(CONFIG_ARM)
+#include <asm/arch/clock.h>
+#endif
#if defined(CONFIG_SYS_FSL_ERRATUM_A008511) | \
defined(CONFIG_SYS_FSL_ERRATUM_A009803)
{
unsigned int i, bus_width;
struct ccsr_ddr __iomem *ddr;
- u32 temp_sdram_cfg;
+ u32 temp32;
u32 total_gb_size_per_controller;
int timeout;
+
#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
- u32 temp32, mr6;
+ u32 mr6;
u32 vref_seq1[3] = {0x80, 0x96, 0x16}; /* for range 1 */
u32 vref_seq2[3] = {0xc0, 0xf0, 0x70}; /* for range 2 */
u32 *vref_seq = vref_seq1;
#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A009942
- ulong ddr_freq;
- u32 tmp;
-#endif
#ifdef CONFIG_FSL_DDR_BIST
u32 mtcr, err_detect, err_sbe;
u32 cs0_bnds, cs1_bnds, cs2_bnds, cs3_bnds, cs0_config;
#ifdef CONFIG_FSL_DDR_BIST
char buffer[CONFIG_SYS_CBSIZE];
#endif
-
switch (ctrl_num) {
case 0:
ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
-#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 1)
case 1:
ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 2)
case 2:
ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 3)
case 3:
ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
break;
#ifdef CONFIG_SYS_FSL_ERRATUM_A009803
/* part 1 of 2 */
- if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) { /* for RDIMM */
- ddr_out32(&ddr->ddr_sdram_rcw_2,
- regs->ddr_sdram_rcw_2 & ~0x0f000000);
+ if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
+ if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) { /* for RDIMM */
+ ddr_out32(&ddr->ddr_sdram_rcw_2,
+ regs->ddr_sdram_rcw_2 & ~0x0f000000);
+ }
+ ddr_out32(&ddr->err_disable, regs->err_disable |
+ DDR_ERR_DISABLE_APED);
}
-
- ddr_out32(&ddr->err_disable, regs->err_disable | DDR_ERR_DISABLE_APED);
#else
ddr_out32(&ddr->err_disable, regs->err_disable);
#endif
ddr_out32(&ddr->err_int_en, regs->err_int_en);
- for (i = 0; i < 32; i++) {
+ for (i = 0; i < 64; i++) {
if (regs->debug[i]) {
debug("Write to debug_%d as %08x\n",
i+1, regs->debug[i]);
ddr_out32(&ddr->debug[i], regs->debug[i]);
}
}
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008378
- /* Erratum applies when accumulated ECC is used, or DBI is enabled */
-#define IS_ACC_ECC_EN(v) ((v) & 0x4)
-#define IS_DBI(v) ((((v) >> 12) & 0x3) == 0x2)
- if (has_erratum_a008378()) {
- if (IS_ACC_ECC_EN(regs->ddr_sdram_cfg) ||
- IS_DBI(regs->ddr_sdram_cfg_3))
- ddr_setbits32(&ddr->debug[28], 0x9 << 20);
- }
-#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
/* Part 1 of 2 */
- /* This erraum only applies to verion 5.2.0 */
if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
/* Disable DRAM VRef training */
ddr_out32(&ddr->ddr_cdr2,
temp32 = ddr_in32(&ddr->debug[28]);
temp32 |= DDR_TX_BD_DIS;
ddr_out32(&ddr->debug[28], temp32);
- /* Disable D_INIT */
- ddr_out32(&ddr->sdram_cfg_2,
- regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
ddr_out32(&ddr->debug[25], 0x9000);
+ } else if (fsl_ddr_get_version(ctrl_num) == 0x50201) {
+ /* Output enable forced off */
+ ddr_out32(&ddr->debug[37], 1 << 31);
+ /* Enable Vref training */
+ ddr_out32(&ddr->ddr_cdr2,
+ regs->ddr_cdr2 | DDR_CDR2_VREF_TRAIN_EN);
+ } else {
+ debug("Erratum A008511 doesn't apply.\n");
}
#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A009942
- ddr_freq = get_ddr_freq(ctrl_num) / 1000000;
- tmp = ddr_in32(&ddr->debug[28]);
- if (ddr_freq <= 1333)
- ddr_out32(&ddr->debug[28], tmp | 0x0080006a);
- else if (ddr_freq <= 1600)
- ddr_out32(&ddr->debug[28], tmp | 0x0070006f);
- else if (ddr_freq <= 1867)
- ddr_out32(&ddr->debug[28], tmp | 0x00700076);
- else if (ddr_freq <= 2133)
- ddr_out32(&ddr->debug[28], tmp | 0x0060007b);
+#if defined(CONFIG_SYS_FSL_ERRATUM_A009803) || \
+ defined(CONFIG_SYS_FSL_ERRATUM_A008511)
+ /* Disable D_INIT */
+ ddr_out32(&ddr->sdram_cfg_2,
+ regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009801
+ temp32 = ddr_in32(&ddr->debug[25]);
+ temp32 &= ~DDR_CAS_TO_PRE_SUB_MASK;
+ temp32 |= 9 << DDR_CAS_TO_PRE_SUB_SHIFT;
+ ddr_out32(&ddr->debug[25], temp32);
+#endif
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A010165
+ temp32 = get_ddr_freq(ctrl_num) / 1000000;
+ if ((temp32 > 1900) && (temp32 < 2300)) {
+ temp32 = ddr_in32(&ddr->debug[28]);
+ ddr_out32(&ddr->debug[28], temp32 | 0x000a0000);
+ }
+#endif
/*
* For RDIMMs, JEDEC spec requires clocks to be stable before reset is
* deasserted. Clocks start when any chip select is enabled and clock
step2:
/* Set, but do not enable the memory */
- temp_sdram_cfg = regs->ddr_sdram_cfg;
- temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN);
- ddr_out32(&ddr->sdram_cfg, temp_sdram_cfg);
+ temp32 = regs->ddr_sdram_cfg;
+ temp32 &= ~(SDRAM_CFG_MEM_EN);
+ ddr_out32(&ddr->sdram_cfg, temp32);
/*
* 500 painful micro-seconds must elapse between
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* enter self-refresh */
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
- temp_sdram_cfg |= SDRAM_CFG2_FRC_SR;
- ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ temp32 = ddr_in32(&ddr->sdram_cfg_2);
+ temp32 |= SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp32);
/* do board specific memory setup */
board_mem_sleep_setup();
- temp_sdram_cfg = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
+ temp32 = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
} else
#endif
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
+ temp32 = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
/* Let the controller go */
- ddr_out32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN);
+ ddr_out32(&ddr->sdram_cfg, temp32 | SDRAM_CFG_MEM_EN);
mb();
isb();
#if defined(CONFIG_SYS_FSL_ERRATUM_A008511) || \
defined(CONFIG_SYS_FSL_ERRATUM_A009803)
/* Part 2 of 2 */
- /* This erraum only applies to verion 5.2.0 */
- if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
- /* Wait for idle */
- timeout = 40;
- while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
- (timeout > 0)) {
- udelay(1000);
- timeout--;
- }
- if (timeout <= 0) {
- printf("Controler %d timeout, debug_2 = %x\n",
- ctrl_num, ddr_in32(&ddr->debug[1]));
- }
+ timeout = 40;
+ /* Wait for idle. D_INIT needs to be cleared earlier, or timeout */
+ while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
+ (timeout > 0)) {
+ udelay(1000);
+ timeout--;
+ }
+ if (timeout <= 0) {
+ printf("Controler %d timeout, debug_2 = %x\n",
+ ctrl_num, ddr_in32(&ddr->debug[1]));
+ }
#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
+ /* This erraum only applies to verion 5.2.0 */
+ if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
/* The vref setting sequence is different for range 2 */
if (regs->ddr_cdr2 & DDR_CDR2_VREF_RANGE_2)
vref_seq = vref_seq2;
printf("Controler %d timeout, debug_2 = %x\n",
ctrl_num, ddr_in32(&ddr->debug[1]));
}
- /* Restore D_INIT */
- ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+ }
#endif /* CONFIG_SYS_FSL_ERRATUM_A008511 */
#ifdef CONFIG_SYS_FSL_ERRATUM_A009803
+ if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
/* if it's RDIMM */
if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) {
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
ddr_out32(&ddr->err_disable,
regs->err_disable & ~DDR_ERR_DISABLE_APED);
-#endif
}
#endif
+ /* Restore D_INIT */
+ ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+#endif
total_gb_size_per_controller = 0;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* exit self-refresh */
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
- temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR;
- ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ temp32 = ddr_in32(&ddr->sdram_cfg_2);
+ temp32 &= ~SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp32);
}
#endif
projects / platform / kernel / u-boot.git / blobdiff