#include <asm/processor.h>
#include <fsl_immap.h>
#include <fsl_ddr.h>
+#include <fsl_errata.h>
+#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3) || \
+ defined(CONFIG_ARM)
+#include <asm/arch/clock.h>
+#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
+#if defined(CONFIG_SYS_FSL_ERRATUM_A008511) | \
+ defined(CONFIG_SYS_FSL_ERRATUM_A009803)
static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
{
int timeout = 1000;
timeout--;
}
if (timeout <= 0)
- puts("Error: A007865 wait for clear timeout.\n");
+ puts("Error: wait for clear timeout.\n");
}
-#endif /* CONFIG_SYS_FSL_ERRATUM_A008511 */
+#endif
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
{
unsigned int i, bus_width;
struct ccsr_ddr __iomem *ddr;
- u32 temp_sdram_cfg;
+ u32 temp32;
u32 total_gb_size_per_controller;
int timeout;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
- defined(CONFIG_SYS_FSL_ERRATUM_A008514)
- u32 *eddrtqcr1;
-#endif
+
#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
- u32 temp32, mr6;
+ u32 mr6;
+ u32 vref_seq1[3] = {0x80, 0x96, 0x16}; /* for range 1 */
+ u32 vref_seq2[3] = {0xc0, 0xf0, 0x70}; /* for range 2 */
+ u32 *vref_seq = vref_seq1;
#endif
#ifdef CONFIG_FSL_DDR_BIST
u32 mtcr, err_detect, err_sbe;
#ifdef CONFIG_FSL_DDR_BIST
char buffer[CONFIG_SYS_CBSIZE];
#endif
-
switch (ctrl_num) {
case 0:
ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
- defined(CONFIG_SYS_FSL_ERRATUM_A008514)
- eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR_ADDR + 0x800;
-#endif
break;
-#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 1)
case 1:
ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
- defined(CONFIG_SYS_FSL_ERRATUM_A008514)
- eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR2_ADDR + 0x800;
-#endif
break;
#endif
-#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 2)
case 2:
ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
- defined(CONFIG_SYS_FSL_ERRATUM_A008514)
- eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR3_ADDR + 0x800;
-#endif
break;
#endif
-#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 3)
case 3:
ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
- defined(CONFIG_SYS_FSL_ERRATUM_A008514)
- eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR4_ADDR + 0x800;
-#endif
break;
#endif
default:
if (step == 2)
goto step2;
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
-#ifdef CONFIG_LS2085A
- /* A008336 only applies to general DDR controllers */
- if ((ctrl_num == 0) || (ctrl_num == 1))
-#endif
- ddr_out32(eddrtqcr1, 0x63b30002);
-#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
-#ifdef CONFIG_LS2085A
- /* A008514 only applies to DP-DDR controler */
- if (ctrl_num == 2)
-#endif
- ddr_out32(eddrtqcr1, 0x63b20002);
-#endif
if (regs->ddr_eor)
ddr_out32(&ddr->eor, regs->ddr_eor);
ddr_out32(&ddr->sdram_mode_15, regs->ddr_sdram_mode_15);
ddr_out32(&ddr->sdram_mode_16, regs->ddr_sdram_mode_16);
ddr_out32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009663
+ ddr_out32(&ddr->sdram_interval,
+ regs->ddr_sdram_interval & ~SDRAM_INTERVAL_BSTOPRE);
+#else
ddr_out32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+#endif
ddr_out32(&ddr->sdram_data_init, regs->ddr_data_init);
ddr_out32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
#ifndef CONFIG_SYS_FSL_DDR_EMU
ddr_out32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
ddr_out32(&ddr->ddr_cdr2, regs->ddr_cdr2);
}
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009803
+ /* part 1 of 2 */
+ if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
+ if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) { /* for RDIMM */
+ ddr_out32(&ddr->ddr_sdram_rcw_2,
+ regs->ddr_sdram_rcw_2 & ~0x0f000000);
+ }
+ ddr_out32(&ddr->err_disable, regs->err_disable |
+ DDR_ERR_DISABLE_APED);
+ }
+#else
ddr_out32(&ddr->err_disable, regs->err_disable);
+#endif
ddr_out32(&ddr->err_int_en, regs->err_int_en);
- for (i = 0; i < 32; i++) {
+ for (i = 0; i < 64; i++) {
if (regs->debug[i]) {
debug("Write to debug_%d as %08x\n",
i+1, regs->debug[i]);
ddr_out32(&ddr->debug[i], regs->debug[i]);
}
}
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008378
- /* Erratum applies when accumulated ECC is used, or DBI is enabled */
-#define IS_ACC_ECC_EN(v) ((v) & 0x4)
-#define IS_DBI(v) ((((v) >> 12) & 0x3) == 0x2)
- if (IS_ACC_ECC_EN(regs->ddr_sdram_cfg) ||
- IS_DBI(regs->ddr_sdram_cfg_3))
- ddr_setbits32(ddr->debug[28], 0x9 << 20);
-#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
/* Part 1 of 2 */
- /* This erraum only applies to verion 5.2.0 */
if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
/* Disable DRAM VRef training */
ddr_out32(&ddr->ddr_cdr2,
regs->ddr_cdr2 & ~DDR_CDR2_VREF_TRAIN_EN);
- /* Disable deskew */
- ddr_out32(&ddr->debug[28], 0x400);
- /* Disable D_INIT */
- ddr_out32(&ddr->sdram_cfg_2,
- regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
+ /* disable transmit bit deskew */
+ temp32 = ddr_in32(&ddr->debug[28]);
+ temp32 |= DDR_TX_BD_DIS;
+ ddr_out32(&ddr->debug[28], temp32);
ddr_out32(&ddr->debug[25], 0x9000);
+ } else if (fsl_ddr_get_version(ctrl_num) == 0x50201) {
+ /* Output enable forced off */
+ ddr_out32(&ddr->debug[37], 1 << 31);
+ /* Enable Vref training */
+ ddr_out32(&ddr->ddr_cdr2,
+ regs->ddr_cdr2 | DDR_CDR2_VREF_TRAIN_EN);
+ } else {
+ debug("Erratum A008511 doesn't apply.\n");
+ }
+#endif
+
+#if defined(CONFIG_SYS_FSL_ERRATUM_A009803) || \
+ defined(CONFIG_SYS_FSL_ERRATUM_A008511)
+ /* Disable D_INIT */
+ ddr_out32(&ddr->sdram_cfg_2,
+ regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
+#endif
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009801
+ temp32 = ddr_in32(&ddr->debug[25]);
+ temp32 &= ~DDR_CAS_TO_PRE_SUB_MASK;
+ temp32 |= 9 << DDR_CAS_TO_PRE_SUB_SHIFT;
+ ddr_out32(&ddr->debug[25], temp32);
+#endif
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A010165
+ temp32 = get_ddr_freq(ctrl_num) / 1000000;
+ if ((temp32 > 1900) && (temp32 < 2300)) {
+ temp32 = ddr_in32(&ddr->debug[28]);
+ ddr_out32(&ddr->debug[28], temp32 | 0x000a0000);
}
#endif
/*
step2:
/* Set, but do not enable the memory */
- temp_sdram_cfg = regs->ddr_sdram_cfg;
- temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN);
- ddr_out32(&ddr->sdram_cfg, temp_sdram_cfg);
+ temp32 = regs->ddr_sdram_cfg;
+ temp32 &= ~(SDRAM_CFG_MEM_EN);
+ ddr_out32(&ddr->sdram_cfg, temp32);
/*
* 500 painful micro-seconds must elapse between
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* enter self-refresh */
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
- temp_sdram_cfg |= SDRAM_CFG2_FRC_SR;
- ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ temp32 = ddr_in32(&ddr->sdram_cfg_2);
+ temp32 |= SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp32);
/* do board specific memory setup */
board_mem_sleep_setup();
- temp_sdram_cfg = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
+ temp32 = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
} else
#endif
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
+ temp32 = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
/* Let the controller go */
- ddr_out32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN);
+ ddr_out32(&ddr->sdram_cfg, temp32 | SDRAM_CFG_MEM_EN);
mb();
isb();
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
+#if defined(CONFIG_SYS_FSL_ERRATUM_A008511) || \
+ defined(CONFIG_SYS_FSL_ERRATUM_A009803)
/* Part 2 of 2 */
+ timeout = 40;
+ /* Wait for idle. D_INIT needs to be cleared earlier, or timeout */
+ while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
+ (timeout > 0)) {
+ udelay(1000);
+ timeout--;
+ }
+ if (timeout <= 0) {
+ printf("Controler %d timeout, debug_2 = %x\n",
+ ctrl_num, ddr_in32(&ddr->debug[1]));
+ }
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008511
/* This erraum only applies to verion 5.2.0 */
if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
- /* Wait for idle */
- timeout = 200;
- while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
- (timeout > 0)) {
- udelay(100);
- timeout--;
- }
- if (timeout <= 0) {
- printf("Controler %d timeout, debug_2 = %x\n",
- ctrl_num, ddr_in32(&ddr->debug[1]));
- }
+ /* The vref setting sequence is different for range 2 */
+ if (regs->ddr_cdr2 & DDR_CDR2_VREF_RANGE_2)
+ vref_seq = vref_seq2;
+
/* Set VREF */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (!(regs->cs[i].config & SDRAM_CS_CONFIG_EN))
MD_CNTL_CS_SEL(i) |
MD_CNTL_MD_SEL(6) |
0x00200000;
- temp32 = mr6 | 0xc0;
+ temp32 = mr6 | vref_seq[0];
set_wait_for_bits_clear(&ddr->sdram_md_cntl,
temp32, MD_CNTL_MD_EN);
udelay(1);
debug("MR6 = 0x%08x\n", temp32);
- temp32 = mr6 | 0xf0;
+ temp32 = mr6 | vref_seq[1];
set_wait_for_bits_clear(&ddr->sdram_md_cntl,
temp32, MD_CNTL_MD_EN);
udelay(1);
debug("MR6 = 0x%08x\n", temp32);
- temp32 = mr6 | 0x70;
+ temp32 = mr6 | vref_seq[2];
set_wait_for_bits_clear(&ddr->sdram_md_cntl,
temp32, MD_CNTL_MD_EN);
udelay(1);
debug("MR6 = 0x%08x\n", temp32);
}
ddr_out32(&ddr->sdram_md_cntl, 0);
- ddr_out32(&ddr->debug[28], 0); /* Enable deskew */
+ temp32 = ddr_in32(&ddr->debug[28]);
+ temp32 &= ~DDR_TX_BD_DIS; /* Enable deskew */
+ ddr_out32(&ddr->debug[28], temp32);
ddr_out32(&ddr->debug[1], 0x400); /* restart deskew */
/* wait for idle */
- timeout = 200;
+ timeout = 40;
while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
(timeout > 0)) {
- udelay(100);
+ udelay(1000);
timeout--;
}
if (timeout <= 0) {
printf("Controler %d timeout, debug_2 = %x\n",
ctrl_num, ddr_in32(&ddr->debug[1]));
}
- /* Restore D_INIT */
- ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
}
#endif /* CONFIG_SYS_FSL_ERRATUM_A008511 */
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009803
+ if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
+ /* if it's RDIMM */
+ if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) {
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (!(regs->cs[i].config & SDRAM_CS_CONFIG_EN))
+ continue;
+ set_wait_for_bits_clear(&ddr->sdram_md_cntl,
+ MD_CNTL_MD_EN |
+ MD_CNTL_CS_SEL(i) |
+ 0x070000ed,
+ MD_CNTL_MD_EN);
+ udelay(1);
+ }
+ }
+
+ ddr_out32(&ddr->err_disable,
+ regs->err_disable & ~DDR_ERR_DISABLE_APED);
+ }
+#endif
+ /* Restore D_INIT */
+ ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+#endif
+
total_gb_size_per_controller = 0;
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (!(regs->cs[i].config & 0x80000000))
if (timeout <= 0)
printf("Waiting for D_INIT timeout. Memory may not work.\n");
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A009663
+ ddr_out32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+#endif
+
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* exit self-refresh */
- temp_sdram_cfg = ddr_in32(&ddr->sdram_cfg_2);
- temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR;
- ddr_out32(&ddr->sdram_cfg_2, temp_sdram_cfg);
+ temp32 = ddr_in32(&ddr->sdram_cfg_2);
+ temp32 &= ~SDRAM_CFG2_FRC_SR;
+ ddr_out32(&ddr->sdram_cfg_2, temp32);
}
#endif
if (getenv_f("ddr_bist", buffer, CONFIG_SYS_CBSIZE) >= 0) {
puts("Running BIST test. This will take a while...");
cs0_config = ddr_in32(&ddr->cs0_config);
+ cs0_bnds = ddr_in32(&ddr->cs0_bnds);
+ cs1_bnds = ddr_in32(&ddr->cs1_bnds);
+ cs2_bnds = ddr_in32(&ddr->cs2_bnds);
+ cs3_bnds = ddr_in32(&ddr->cs3_bnds);
if (cs0_config & CTLR_INTLV_MASK) {
- cs0_bnds = ddr_in32(&cs0_bnds);
- cs1_bnds = ddr_in32(&cs1_bnds);
- cs2_bnds = ddr_in32(&cs2_bnds);
- cs3_bnds = ddr_in32(&cs3_bnds);
/* set bnds to non-interleaving */
- ddr_out32(&cs0_bnds, (cs0_bnds & 0xfffefffe) >> 1);
- ddr_out32(&cs1_bnds, (cs1_bnds & 0xfffefffe) >> 1);
- ddr_out32(&cs2_bnds, (cs2_bnds & 0xfffefffe) >> 1);
- ddr_out32(&cs3_bnds, (cs3_bnds & 0xfffefffe) >> 1);
+ ddr_out32(&ddr->cs0_bnds, (cs0_bnds & 0xfffefffe) >> 1);
+ ddr_out32(&ddr->cs1_bnds, (cs1_bnds & 0xfffefffe) >> 1);
+ ddr_out32(&ddr->cs2_bnds, (cs2_bnds & 0xfffefffe) >> 1);
+ ddr_out32(&ddr->cs3_bnds, (cs3_bnds & 0xfffefffe) >> 1);
}
ddr_out32(&ddr->mtp1, BIST_PATTERN1);
ddr_out32(&ddr->mtp2, BIST_PATTERN1);
if (cs0_config & CTLR_INTLV_MASK) {
/* restore bnds registers */
- ddr_out32(&cs0_bnds, cs0_bnds);
- ddr_out32(&cs1_bnds, cs1_bnds);
- ddr_out32(&cs2_bnds, cs2_bnds);
- ddr_out32(&cs3_bnds, cs3_bnds);
+ ddr_out32(&ddr->cs0_bnds, cs0_bnds);
+ ddr_out32(&ddr->cs1_bnds, cs1_bnds);
+ ddr_out32(&ddr->cs2_bnds, cs2_bnds);
+ ddr_out32(&ddr->cs3_bnds, cs3_bnds);
}
}
#endif
projects / platform / kernel / u-boot.git / blobdiff