This requires the RTC clocks, etc, to be enabled prior to use and
not all boards with this IP block on it will have the RTC in use.
+config BOOTCOUNT_AM33XX_NVMEM
+ bool "Boot counter in AM33XX RTC IP block with upgrade_available flag"
+ depends on AM33XX
+ select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
+ help
+ Add support for maintaining bootcount,upgrade_available,
+ version and BOOTMAGIC in a AM33xx RTC IP block
+ scratch register2.
+
+ A bootcount driver for the RTC IP block found on many TI platforms.
+ This requires the RTC clocks, etc, to be enabled prior to use and
+ not all boards with this IP block on it will have the RTC in use.
+
+ If there is upgrade in software then "upgrade_available" is 1,
+ "bootcount" is incremented otherwise "upgrade_available" and
+ "bootcount" is always 0. So the Userspace Application must set
+ the "upgrade_available" and "bootcount" variable to 0, if a boot
+ was successfully.
+
config BOOTCOUNT_ENV
bool "Boot counter in environment"
help
pointing to the underlying i2c eeprom device) and an optional 'offset'
property are supported.
+config DM_BOOTCOUNT_SPI_FLASH
+ bool "Support SPI flash devices as a backing store for bootcount"
+ depends on DM_SPI_FLASH
+ help
+ Enabled reading/writing the bootcount in a DM SPI flash device.
+ The wrapper device is to be specified with the compatible string
+ 'u-boot,bootcount-spi-flash' and the 'spi-flash'-property (a phandle
+ pointing to the underlying SPI flash device) and an optional 'offset'
+ property are supported.
+
config BOOTCOUNT_MEM
bool "Support memory based bootcounter"
help
is not cleared on softreset.
compatible = "u-boot,bootcount";
+config DM_BOOTCOUNT_SYSCON
+ bool "Support SYSCON devices as a backing store for bootcount"
+ select REGMAP
+ select SYSCON
+ help
+ Enable reading/writing the bootcount value in a DM SYSCON device.
+ The driver supports a fixed 32 bits size register using the native
+ endianness. However, this can be controlled from the SYSCON DT node
+ configuration.
+
+ Accessing the backend is done using the regmap interface.
+
endmenu
endif
config SYS_BOOTCOUNT_ADDR
hex "RAM address used for reading and writing the boot counter"
- default 0x44E3E000 if BOOTCOUNT_AM33XX
+ default 0x44E3E000 if BOOTCOUNT_AM33XX || BOOTCOUNT_AM33XX_NVMEM
default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
- BOOTCOUNT_I2C
+ BOOTCOUNT_I2C || BOOTCOUNT_AM33XX_NVMEM
help
Set the address used for reading and writing the boot counter.
config SYS_BOOTCOUNT_MAGIC
hex "Magic value for the boot counter"
- default 0xB001C041
+ default 0xB001C041 if BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
+ BOOTCOUNT_AM33XX || BOOTCOUNT_ENV || \
+ BOOTCOUNT_RAM || BOOTCOUNT_I2C || \
+ BOOTCOUNT_AT91 || DM_BOOTCOUNT
+ default 0xB0 if BOOTCOUNT_AM33XX_NVMEM
+ depends on BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
+ BOOTCOUNT_AM33XX || BOOTCOUNT_ENV || \
+ BOOTCOUNT_RAM || BOOTCOUNT_I2C || \
+ BOOTCOUNT_AT91 || DM_BOOTCOUNT || \
+ BOOTCOUNT_AM33XX_NVMEM
help
Set the magic value used for the boot counter.