* SL82C105/Winbond 553 IDE driver
*
* and in part on the documentation and errata sheet
+ *
+ *
+ * Note: The controller like many controllers has shared timings for
+ * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
+ * in the dma_stop function. Thus we actually don't need a set_dmamode
+ * method as the PIO method is always called and will set the right PIO
+ * timing parameters.
*/
#include <linux/kernel.h>
#include <linux/libata.h>
#define DRV_NAME "pata_sl82c105"
-#define DRV_VERSION "0.2.3"
+#define DRV_VERSION "0.3.1"
enum {
/*
/**
* sl82c105_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int sl82c105_pre_reset(struct ata_port *ap)
+static int sl82c105_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits sl82c105_enable_bits[] = {
{ 0x40, 1, 0x01, 0x01 },
if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
return -ENOENT;
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
+ return ata_std_prereset(ap, deadline);
}
}
/**
- * sl82c105_set_dmamode - set initial DMA mode data
- * @ap: ATA interface
- * @adev: ATA device
- *
- * Called to do the DMA mode setup. This replaces the PIO timings
- * for the device in question. Set appropriate PIO timings not DMA
- * timings at this point.
- */
-
-static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
- switch(adev->dma_mode) {
- case XFER_MW_DMA_0:
- sl82c105_configure_piomode(ap, adev, 0);
- break;
- case XFER_MW_DMA_1:
- sl82c105_configure_piomode(ap, adev, 3);
- break;
- case XFER_MW_DMA_2:
- sl82c105_configure_piomode(ap, adev, 4);
- break;
- default:
- BUG();
- }
-}
-
-/**
* sl82c105_reset_engine - Reset the DMA engine
* @ap: ATA interface
*
/* This will redo the initial setup of the DMA device to matching
PIO timings */
- sl82c105_set_dmamode(ap, qc->dev);
+ sl82c105_set_piomode(ap, qc->dev);
}
static struct scsi_host_template sl82c105_sht = {
static struct ata_port_operations sl82c105_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = sl82c105_set_piomode,
- .set_dmamode = sl82c105_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
.error_handler = sl82c105_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = sl82c105_bmdma_start,
static int sl82c105_bridge_revision(struct pci_dev *pdev)
{
struct pci_dev *bridge;
- u8 rev;
/*
* The bridge should be part of the same device, but function 0.
/*
* We need to find function 0's revision, not function 1
*/
- pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);
-
pci_dev_put(bridge);
- return rev;
+ return bridge->revision;
}
static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- static struct ata_port_info info_dma = {
+ static const struct ata_port_info info_dma = {
.sht = &sl82c105_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &sl82c105_port_ops
};
- static struct ata_port_info info_early = {
+ static const struct ata_port_info info_early = {
.sht = &sl82c105_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.port_ops = &sl82c105_port_ops
};
- static struct ata_port_info *port_info[2] = { &info_early, &info_early };
+ /* for now use only the first port */
+ const struct ata_port_info *ppi[] = { &info_early,
+ &ata_dummy_port_info };
u32 val;
int rev;
dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
else if (rev <= 5)
dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n");
- else {
- port_info[0] = &info_dma;
- port_info[1] = &info_dma;
- }
+ else
+ ppi[0] = &info_dma;
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);
-
- return ata_pci_init_one(dev, port_info, 1); /* For now */
+ return ata_pci_init_one(dev, ppi);
}
static const struct pci_device_id sl82c105[] = {