+# SPDX-License-Identifier: GPL-2.0+
NAND FLASH commands and notes
See NOTE below!!!
# (C) Copyright 2003
# Dave Ellis, SIXNET, dge@sixnetio.com
#
-# SPDX-License-Identifier: GPL-2.0+
Commands:
The maximum number of NAND chips per device to be supported.
CONFIG_SYS_NAND_SELF_INIT
- Traditionally, glue code in drivers/mtd/nand/nand.c has driven
+ Traditionally, glue code in drivers/mtd/nand/raw/nand.c has driven
the initialization process -- it provides the mtd and nand
structs, calls a board init function for a specific device,
calls nand_scan(), and registers with mtd.
run code between nand_scan_ident() and nand_scan_tail(), or other
deviations from the "normal" flow.
- If a board defines CONFIG_SYS_NAND_SELF_INIT, drivers/mtd/nand/nand.c
+ If a board defines CONFIG_SYS_NAND_SELF_INIT, drivers/mtd/nand/raw/nand.c
will make one call to board_nand_init(), with no arguments. That
function is responsible for calling a driver init function for
each NAND device on the board, that performs all initialization
init:
/* chip is struct nand_chip, and is now provided by the driver. */
- mtd = &chip.mtd;
+ mtd = nand_to_mtd(&chip);
/*
* Fill in appropriate values if this driver uses these fields,
/*
* devnum is the device number to be used in nand commands
- * and in mtd->name. Must be less than CONFIG_SYS_NAND_MAX_DEVICE.
+ * and in mtd->name. Must be less than CONFIG_SYS_MAX_NAND_DEVICE.
*/
if (nand_register(devnum, mtd))
error out
flexibility, so that one day we can eliminate the old mechanism.
- CONFIG_SYS_NAND_ONFI_DETECTION
- Enables detection of ONFI compliant devices during probe.
- And fetching device parameters flashed on device, by parsing
- ONFI parameter page.
-
- CONFIG_BCH
- Enables software based BCH ECC algorithm present in lib/bch.c
- This is used by SoC platforms which do not have built-in ELM
- hardware engine required for BCH ECC correction.
-
-
Platform specific options
=========================
CONFIG_NAND_OMAP_GPMC
so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
SPL-NAND driver with software ECC correction support.
- CONFIG_NAND_OMAP_ECCSCHEME
- On OMAP platforms, this CONFIG specifies NAND ECC scheme.
- It can take following values:
- OMAP_ECC_HAM1_CODE_SW
- 1-bit Hamming code using software lib.
- (for legacy devices only)
- OMAP_ECC_HAM1_CODE_HW
- 1-bit Hamming code using GPMC hardware.
- (for legacy devices only)
- OMAP_ECC_BCH4_CODE_HW_DETECTION_SW
- 4-bit BCH code (unsupported)
- OMAP_ECC_BCH4_CODE_HW
- 4-bit BCH code (unsupported)
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
- 8-bit BCH code with
- - ecc calculation using GPMC hardware engine,
- - error detection using software library.
- - requires CONFIG_BCH to enable software BCH library
- (For legacy device which do not have ELM h/w engine)
- OMAP_ECC_BCH8_CODE_HW
- 8-bit BCH code with
- - ecc calculation using GPMC hardware engine,
- - error detection using ELM hardware engine.
- OMAP_ECC_BCH16_CODE_HW
- 16-bit BCH code with
- - ecc calculation using GPMC hardware engine,
- - error detection using ELM hardware engine.
-
- How to select ECC scheme on OMAP and AMxx platforms ?
- -----------------------------------------------------
- Though higher ECC schemes have more capability to detect and correct
- bit-flips, but still selection of ECC scheme is dependent on following
- - hardware engines present in SoC.
- Some legacy OMAP SoC do not have ELM h/w engine thus such
- SoC cannot support BCHx_HW ECC schemes.
- - size of OOB/Spare region
- With higher ECC schemes, more OOB/Spare area is required to
- store ECC. So choice of ECC scheme is limited by NAND oobsize.
-
- In general following expression can help:
- NAND_OOBSIZE >= 2 + (NAND_PAGESIZE / 512) * ECC_BYTES
- where
- NAND_OOBSIZE = number of bytes available in
- OOB/spare area per NAND page.
- NAND_PAGESIZE = bytes in main-area of NAND page.
- ECC_BYTES = number of ECC bytes generated to
- protect 512 bytes of data, which is:
- 3 for HAM1_xx ecc schemes
- 7 for BCH4_xx ecc schemes
- 14 for BCH8_xx ecc schemes
- 26 for BCH16_xx ecc schemes
-
- example to check for BCH16 on 2K page NAND
- NAND_PAGESIZE = 2048
- NAND_OOBSIZE = 64
- 2 + (2048 / 512) * 26 = 106 > NAND_OOBSIZE
- Thus BCH16 cannot be supported on 2K page NAND.
-
- However, for 4K pagesize NAND
- NAND_PAGESIZE = 4096
- NAND_OOBSIZE = 224
- ECC_BYTES = 26
- 2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE
- Thus BCH16 can be supported on 4K page NAND.
-
-
CONFIG_NAND_OMAP_GPMC_PREFETCH
On OMAP platforms that use the GPMC controller
(CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
=====
The Disk On Chip driver is currently broken and has been for some time.
-There is a driver in drivers/mtd/nand, taken from Linux, that works with
+There is a driver in drivers/mtd/nand/raw, taken from Linux, that works with
the current NAND system but has not yet been adapted to the u-boot
environment.