#endif /* CONFIG_IOP480 */
/*****************************************************************************/
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_405) || defined(CONFIG_405EP)
+#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
+ defined(CONFIG_405)
/*----------------------------------------------------------------------- */
/* Clear and set up some registers. */
/*----------------------------------------------------------------------- */
/*----------------------------------------------------------------------- */
/* Enable two 128MB cachable regions. */
/*----------------------------------------------------------------------- */
- addis r4,r0,0x8000
- addi r4,r4,0x0001
+ lis r4,0x8000
+ ori r4,r4,0x0001
mticcr r4 /* instruction cache */
isync
- addis r4,r0,0x0000
- addi r4,r4,0x0000
+ lis r4,0x0000
+ ori r4,r4,0x0000
mtdccr r4 /* data cache */
#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
#endif /* CONFIG_405EP */
#if defined(CFG_OCM_DATA_ADDR) && defined(CFG_OCM_DATA_SIZE)
+/* test-only... (clean up later when NAND booting is supported) */
+#if defined(CONFIG_405EZ)
+ /********************************************************************
+ * Setup OCM - On Chip Memory - PPC405EZ uses OCM Controller V2
+ *******************************************************************/
+ /*
+ * We can map the OCM on the PLB3, so map it at
+ * CFG_OCM_DATA_ADDR + 0x8000
+ */
+ lis r3,CFG_OCM_DATA_ADDR@h /* OCM location */
+ ori r3,r3,CFG_OCM_DATA_ADDR@l
+ ori r3,r3,0x8270 /* 32K Offset, 16K for Bank 1, R/W/Enable */
+ mtdcr ocmplb3cr1,r3 /* Set PLB Access */
+ ori r3,r3,0x4000 /* Add 0x4000 for bank 2 */
+ mtdcr ocmplb3cr2,r3 /* Set PLB Access */
+ isync
+
+ lis r3,CFG_OCM_DATA_ADDR@h /* OCM location */
+ ori r3,r3,CFG_OCM_DATA_ADDR@l
+ ori r3,r3,0x0270 /* 16K for Bank 1, R/W/Enable */
+ mtdcr ocmdscr1, r3 /* Set Data Side */
+ mtdcr ocmiscr1, r3 /* Set Instruction Side */
+ ori r3,r3,0x4000 /* Add 0x4000 for bank 2 */
+ mtdcr ocmdscr2, r3 /* Set Data Side */
+ mtdcr ocmiscr2, r3 /* Set Instruction Side */
+ addis r3,0,0x0800 /* OCM Data Parity Disable - 1 Wait State */
+ mtdcr ocmdsisdpc,r4
+
+ isync
+
+#if defined(CONFIG_NAND_SPL)
+ /*
+ * 405EZ can boot from NAND Flash.
+ * If we are booting the SPL (Pre-loader), copy code from
+ * the mapped 4K NAND Flash to the OCM
+ */
+ li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
+ mtctr r4
+ lis r2,CFG_NAND_BOOT_SPL_SRC@h
+ ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
+ lis r3,CFG_NAND_BOOT_SPL_DST@h
+ ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
+spl_loop:
+ lwzu r4,4(r2)
+ stwu r4,4(r3)
+ bdnz spl_loop
+
+ /*
+ * Jump to code in OCM Ram
+ */
+ bl 00f
+00: mflr r10
+ lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
+ ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
+ sub r10,r10,r3
+ addi r10,r10,28
+ mtlr r10
+ blr
+start_ram:
+ sync
+ isync
+#endif
+#else
+/* ...test-only */
/********************************************************************
* Setup OCM - On Chip Memory
*******************************************************************/
addis r4, 0, 0xC000 /* OCM data area enabled */
mtdcr ocmdscntl, r4
isync
+#endif /* CONFIG_405EZ */
#endif
/*----------------------------------------------------------------------- */
relocate_code:
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
- defined(CONFIG_440SPE)
+ defined(CONFIG_440SP) || defined(CONFIG_440SPE)
/*
* On some 440er platforms the cache is enabled in the first TLB (Boot-CS)
* to speed up the boot process. Now this cache needs to be disabled.
#if defined(CONFIG_440)
#define function_prolog(func_name) .text; \
- .align 2; \
- .globl func_name; \
- func_name:
+ .align 2; \
+ .globl func_name; \
+ func_name:
#define function_epilog(func_name) .type func_name,@function; \
- .size func_name,.-func_name
+ .size func_name,.-func_name
/*----------------------------------------------------------------------------+
| mttlb3.
| mftlb3.
+----------------------------------------------------------------------------*/
function_prolog(mftlb3)
- TLBRE(3,3,2)
+ TLBRE(3,3,2)
blr
function_epilog(mftlb3)
| mftlb2.
+----------------------------------------------------------------------------*/
function_prolog(mftlb2)
- TLBRE(3,3,1)
+ TLBRE(3,3,1)
blr
function_epilog(mftlb2)
| mftlb1.
+----------------------------------------------------------------------------*/
function_prolog(mftlb1)
- TLBRE(3,3,0)
+ TLBRE(3,3,0)
blr
function_epilog(mftlb1)
+
+/*----------------------------------------------------------------------------+
+| dcbz_area.
++----------------------------------------------------------------------------*/
+ function_prolog(dcbz_area)
+ rlwinm. r5,r4,0,27,31
+ rlwinm r5,r4,27,5,31
+ beq ..d_ra2
+ addi r5,r5,0x0001
+..d_ra2:mtctr r5
+..d_ag2:dcbz r0,r3
+ addi r3,r3,32
+ bdnz ..d_ag2
+ sync
+ blr
+ function_epilog(dcbz_area)
+
+/*----------------------------------------------------------------------------+
+| dflush. Assume 32K at vector address is cachable.
++----------------------------------------------------------------------------*/
+ function_prolog(dflush)
+ mfmsr r9
+ rlwinm r8,r9,0,15,13
+ rlwinm r8,r8,0,17,15
+ mtmsr r8
+ addi r3,r0,0x0000
+ mtspr dvlim,r3
+ mfspr r3,ivpr
+ addi r4,r0,1024
+ mtctr r4
+..dflush_loop:
+ lwz r6,0x0(r3)
+ addi r3,r3,32
+ bdnz ..dflush_loop
+ addi r3,r3,-32
+ mtctr r4
+..ag: dcbf r0,r3
+ addi r3,r3,-32
+ bdnz ..ag
+ sync
+ mtmsr r9
+ blr
+ function_epilog(dflush)
#endif /* CONFIG_440 */
projects / platform / kernel / u-boot.git / blobdiff