/*-----------------------------------------------------------------------------+
+ * This source code is dual-licensed. You may use it under the terms of
+ * the GNU General Public license version 2, or under the license below.
*
* This source code has been made available to you by IBM on an AS-IS
* basis. Anyone receiving this source is licensed under IBM
#include <common.h>
#include <command.h>
-#if !defined(CONFIG_440)
#include <asm/4xx_pci.h>
-#endif
#include <asm/processor.h>
+#include <asm/io.h>
#include <pci.h>
#ifdef CONFIG_PCI
DECLARE_GLOBAL_DATA_PTR;
+#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
+
+#if defined(CONFIG_PMC405)
+ushort pmc405_pci_subsys_deviceid(void);
+#endif
+
+/*#define DEBUG*/
+
/*
* Board-specific pci initialization
* Platform code can reimplement pci_pre_init() if needed
*/
int __pci_pre_init(struct pci_controller *hose)
{
+#if defined(CONFIG_405EP)
+ /*
+ * Enable the internal PCI arbiter by default.
+ *
+ * On 405EP CPUs the internal arbiter can be controlled
+ * by the I2C strapping EEPROM. If you want to do so
+ * or if you want to disable the arbiter pci_pre_init()
+ * must be reimplemented without enabling the arbiter.
+ * The arbiter is enabled in this place because of
+ * compatibility reasons.
+ */
+ mtdcr(CPC0_PCI, mfdcr(CPC0_PCI) | CPC0_PCI_ARBIT_EN);
+#endif /* CONFIG_405EP */
+
return 1;
}
-int pci_pre_init(struct pci_controller *hose) __attribute__((weak, alias("__pci_pre_init")));
-
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
+int pci_pre_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_pre_init")));
-#if defined(CONFIG_PMC405)
-ushort pmc405_pci_subsys_deviceid(void);
+int __is_pci_host(struct pci_controller *hose)
+{
+#if defined(CONFIG_405GP)
+ if (mfdcr(CPC0_PSR) & PSR_PCI_ARBIT_EN)
+ return 1;
+#elif defined (CONFIG_405EP)
+ if (mfdcr(CPC0_PCI) & CPC0_PCI_ARBIT_EN)
+ return 1;
#endif
-
-/*#define DEBUG*/
+ return 0;
+}
+int is_pci_host(struct pci_controller *hose) __attribute__((weak, alias("__is_pci_host")));
/*-----------------------------------------------------------------------------+
* pci_init. Initializes the 405GP PCI Configuration regs.
bd_t *bd = gd->bd;
unsigned short temp_short;
- unsigned long ptmpcila[2] = {CFG_PCI_PTM1PCI, CFG_PCI_PTM2PCI};
-#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405)
+ unsigned long ptmpcila[2] = {CONFIG_SYS_PCI_PTM1PCI, CONFIG_SYS_PCI_PTM2PCI};
+#if defined(CONFIG_PCI_4xx_PTM_OVERWRITE)
char *ptmla_str, *ptmms_str;
#endif
- unsigned long ptmla[2] = {CFG_PCI_PTM1LA, CFG_PCI_PTM2LA};
- unsigned long ptmms[2] = {CFG_PCI_PTM1MS, CFG_PCI_PTM2MS};
+ unsigned long ptmla[2] = {CONFIG_SYS_PCI_PTM1LA, CONFIG_SYS_PCI_PTM2LA};
+ unsigned long ptmms[2] = {CONFIG_SYS_PCI_PTM1MS, CONFIG_SYS_PCI_PTM2MS};
#if defined(CONFIG_PIP405) || defined (CONFIG_MIP405)
unsigned long pmmla[3] = {0x80000000, 0xA0000000, 0};
unsigned long pmmma[3] = {0xE0000001, 0xE0000001, 0};
#endif
#endif
-#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405)
+#if defined(CONFIG_PCI_4xx_PTM_OVERWRITE)
ptmla_str = getenv("ptm1la");
ptmms_str = getenv("ptm1ms");
if(NULL != ptmla_str && NULL != ptmms_str ) {
ptmpcila[i], ptmla[i],
~(ptmms[i] & 0xfffff000) + 1,
PCI_REGION_MEM |
- PCI_REGION_MEMORY);
+ PCI_REGION_SYS_MEMORY);
}
/* PCI memory spaces */
pciauto_region_init(hose->pci_fb);
/* Let board change/modify hose & do initial checks */
- if (pci_pre_init (hose) == 0) {
+ if (pci_pre_init(hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return;
/*
* Insert Subsystem Vendor and Device ID
*/
- pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_VENDOR_ID, CFG_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_VENDOR_ID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
#ifdef CONFIG_CPCI405
- if (mfdcr(strap) & PSR_PCI_ARBIT_EN)
- pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID);
+ if (is_pci_host(hose))
+ pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
else
- pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID2);
+ pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID2);
#else
- pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID);
+ pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
#endif
/*
* Insert Class-code
*/
-#ifdef CFG_PCI_CLASSCODE
- pci_write_config_word(PCIDEVID_405GP, PCI_CLASS_SUB_CODE, CFG_PCI_CLASSCODE);
-#endif /* CFG_PCI_CLASSCODE */
+#ifdef CONFIG_SYS_PCI_CLASSCODE
+ pci_write_config_word(PCIDEVID_405GP, PCI_CLASS_SUB_CODE, CONFIG_SYS_PCI_CLASSCODE);
+#endif /* CONFIG_SYS_PCI_CLASSCODE */
/*--------------------------------------------------------------------------+
- * If PCI speed = 66Mhz, set 66Mhz capable bit.
+ * If PCI speed = 66MHz, set 66MHz capable bit.
*--------------------------------------------------------------------------*/
if (bd->bi_pci_busfreq >= 66000000) {
pci_read_config_word(PCIDEVID_405GP, PCI_STATUS, &temp_short);
#if (CONFIG_PCI_HOST != PCI_HOST_ADAPTER)
#if (CONFIG_PCI_HOST == PCI_HOST_AUTO)
- if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) ||
+ if (is_pci_host(hose) ||
(((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0)))
#endif
{
}
#endif
-#if defined(CONFIG_405EP) /* on ppc405ep vendor id is not set */
- pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, 0x1014); /* IBM */
+#if defined(CONFIG_405EP)
+ /*
+ * on ppc405ep vendor/device id is not set
+ * The user manual says 0x1014 (IBM) / 0x0156 (405GP!)
+ * are the correct values.
+ */
+ pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, PCI_VENDOR_ID_IBM);
+ pci_write_config_word(PCIDEVID_405GP,
+ PCI_DEVICE_ID, PCI_DEVICE_ID_IBM_405GP);
#endif
/*
* Scan the PCI bus and configure devices found.
*--------------------------------------------------------------------------*/
#if (CONFIG_PCI_HOST == PCI_HOST_AUTO)
- if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) ||
+ if (is_pci_host(hose) ||
(((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0)))
#endif
{
*/
static struct pci_config_table pci_405gp_config_table[] = {
/*if VendID is 0 it terminates the table search (ie Walnut)*/
-#ifdef CFG_PCI_SUBSYS_VENDORID
- {CFG_PCI_SUBSYS_VENDORID, PCI_ANY_ID, PCI_CLASS_BRIDGE_HOST,
+#ifdef CONFIG_SYS_PCI_SUBSYS_VENDORID
+ {CONFIG_SYS_PCI_SUBSYS_VENDORID, PCI_ANY_ID, PCI_CLASS_BRIDGE_HOST,
PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_bridge},
#endif
{PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA,
static struct pci_controller ppc440_hose = {0};
+/*
+ * This routine is called to determine if a pci scan should be
+ * performed. With various hardware environments (especially cPCI and
+ * PPMC) it's insufficient to depend on the state of the arbiter enable
+ * bit in the strap register, or generic host/adapter assumptions.
+ *
+ * Rather than hard-code a bad assumption in the general 440 code, the
+ * 440 pci code requires the board to decide at runtime.
+ *
+ * Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ * Weak default implementation: "Normal" boards implement the PCI
+ * host functionality. This can be overridden for PCI adapter boards.
+ */
+int __is_pci_host(struct pci_controller *hose)
+{
+ return 1;
+}
+int is_pci_host(struct pci_controller *hose)
+ __attribute__((weak, alias("__is_pci_host")));
+
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX)
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+/*
+ * pci_target_init
+ *
+ * The bootstrap configuration provides default settings for the pci
+ * inbound map (PIM). But the bootstrap config choices are limited and
+ * may not be sufficient for a given board.
+ */
+void __pci_target_init(struct pci_controller *hose)
+{
+ /*
+ * Set up Direct MMIO registers
+ */
+
+ /*
+ * PowerPC440 EP PCI Master configuration.
+ * Map one 1Gig range of PLB/processor addresses to PCI memory space.
+ * PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
+ * Use byte reversed out routines to handle endianess.
+ * Make this region non-prefetchable.
+ */
+ /* PMM0 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM0MA, 0x00000000);
+ /* PMM0 Local Address */
+ out_le32((void *)PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI Low Address */
+ out_le32((void *)PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI High Address */
+ out_le32((void *)PCIL0_PMM0PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM0MA, 0xE0000001);
+
+ /* PMM1 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM1MA, 0x00000000);
+ /* PMM1 Local Address */
+ out_le32((void *)PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI Low Address */
+ out_le32((void *)PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI High Address */
+ out_le32((void *)PCIL0_PMM1PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM1MA, 0xE0000001);
+
+ out_le32((void *)PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out_le32((void *)PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM2LA, 0); /* Local Addr. Reg */
+
+ /*
+ * Set up Configuration registers
+ */
+
+ /* Program the board's subsystem id/vendor id */
+ pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
+
+ /* Configure command register as bus master */
+ pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+ /* 240nS PCI clock */
+ pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+ /* No error reporting */
+ pci_write_config_word(0, PCI_ERREN, 0);
+
+ pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+}
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+/*
+ * pci_pre_init
+ *
+ * This routine is called just prior to registering the hose and gives
+ * the board the opportunity to check things. Returning a value of zero
+ * indicates that things are bad & PCI initialization should be aborted.
+ *
+ * Different boards may wish to customize the pci controller structure
+ * (add regions, override default access routines, etc) or perform
+ * certain pre-initialization actions.
+ *
+ */
+int __pci_pre_init(struct pci_controller *hose)
+{
+ u32 reg;
+
+ /*
+ * Set priority for all PLB3 devices to 0.
+ * Set PLB3 arbiter to fair mode.
+ */
+ mfsdr(SD0_AMP1, reg);
+ mtsdr(SD0_AMP1, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, reg | 0x80000000);
+
+ /*
+ * Set priority for all PLB4 devices to 0.
+ */
+ mfsdr(SD0_AMP0, reg);
+ mtsdr(SD0_AMP0, (reg & 0x000000FF) | 0x0000FF00);
+ reg = mfdcr(PLB4_ACR) | 0xa0000000;
+ mtdcr(PLB4_ACR, reg);
+
+ /*
+ * Set Nebula PLB4 arbiter to fair mode.
+ */
+ /* Segment0 */
+ reg = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ reg = (reg & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, reg);
+
+ /* Segment1 */
+ reg = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ reg = (reg & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ reg = (reg & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ reg = (reg & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, reg);
+
+#if defined(CONFIG_SYS_PCI_BOARD_FIXUP_IRQ)
+ hose->fixup_irq = board_pci_fixup_irq;
+#endif
+
+ return 1;
+}
+
+#else /* defined(CONFIG_440EP) ... */
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+void __pci_target_init(struct pci_controller * hose)
+{
+ /*
+ * Disable everything
+ */
+ out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
+ out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
+
+ /*
+ * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+ * strapping options do not support sizes such as 128/256 MB.
+ */
+ out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out_le32((void *)PCIL0_PIM0LAH, 0);
+ out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out_le32((void *)PCIL0_BAR0, 0);
+
+ /*
+ * Program the board's subsystem id/vendor id
+ */
+ out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+
+ out_le16((void *)PCIL0_CMD, in_le16((void *)PCIL0_CMD) |
+ PCI_COMMAND_MEMORY);
+}
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+int __pci_pre_init(struct pci_controller *hose)
+{
+ /*
+ * This board is always configured as the host & requires the
+ * PCI arbiter to be enabled.
+ */
+ if (!pci_arbiter_enabled()) {
+ printf("PCI: PCI Arbiter disabled!\n");
+ return 0;
+ }
+
+ return 1;
+}
+
+#endif /* defined(CONFIG_440EP) ... */
+
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose)
+ __attribute__((weak, alias("__pci_target_init")));
+#endif /* CONFIG_SYS_PCI_TARGET_INIT */
+
+int pci_pre_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_pre_init")));
+
+#if defined(CONFIG_SYS_PCI_MASTER_INIT)
+void __pci_master_init(struct pci_controller *hose)
+{
+ u16 reg;
+
+ /*
+ * Write the PowerPC440 EP PCI Configuration regs.
+ * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+ * Enable PowerPC440 EP to act as a PCI memory target (PTM).
+ */
+ pci_read_config_word(0, PCI_COMMAND, ®);
+ pci_write_config_word(0, PCI_COMMAND, reg |
+ PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
+}
+void pci_master_init(struct pci_controller *hose)
+ __attribute__((weak, alias("__pci_master_init")));
+#endif /* CONFIG_SYS_PCI_MASTER_INIT */
int pci_440_init (struct pci_controller *hose)
{
#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long strap;
- mfsdr(sdr_sdstp1,strap);
+ mfsdr(SDR0_SDSTP1,strap);
if ((strap & SDR0_SDSTP1_PISE_MASK) == 0) {
printf("PCI: SDR0_STRP1[PISE] not set.\n");
printf("PCI: Configuration aborted.\n");
#elif defined(CONFIG_440GP)
unsigned long strap;
- strap = mfdcr(cpc0_strp1);
+ strap = mfdcr(CPC0_STRP1);
if ((strap & CPC0_STRP1_PISE_MASK) == 0) {
printf("PCI: CPC0_STRP1[PISE] not set.\n");
printf("PCI: Configuration aborted.\n");
/* PCI I/O space */
pci_set_region(hose->regions + reg_num++,
0x00000000,
- PCIX0_IOBASE,
+ PCIL0_IOBASE,
0x10000,
PCI_REGION_IO);
/* PCI memory space */
pci_set_region(hose->regions + reg_num++,
- CFG_PCI_TARGBASE,
- CFG_PCI_MEMBASE,
-#ifdef CFG_PCI_MEMSIZE
- CFG_PCI_MEMSIZE,
+ CONFIG_SYS_PCI_TARGBASE,
+ CONFIG_SYS_PCI_MEMBASE,
+#ifdef CONFIG_SYS_PCI_MEMSIZE
+ CONFIG_SYS_PCI_MEMSIZE,
#else
0x10000000,
#endif
CONFIG_PCI_SYS_MEM_BUS,
CONFIG_PCI_SYS_MEM_PHYS,
CONFIG_PCI_SYS_MEM_SIZE,
- PCI_REGION_MEM | PCI_REGION_MEMORY );
+ PCI_REGION_MEM | PCI_REGION_SYS_MEMORY );
#endif
hose->region_count = reg_num;
- pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA);
+ pci_setup_indirect(hose, PCIL0_CFGADR, PCIL0_CFGDATA);
/* Let board change/modify hose & do initial checks */
- if (pci_pre_init (hose) == 0) {
+ if (pci_pre_init(hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return -1;
/*--------------------------------------------------------------------------+
* PCI target init
*--------------------------------------------------------------------------*/
-#if defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
pci_target_init(hose); /* Let board setup pci target */
#else
- out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_ID );
- out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_ID );
+ out16r( PCIL0_CLS, 0x00060000 ); /* Bridge, host bridge */
#endif
#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
- out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
- out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
-#elif defined(PCIX0_BRDGOPT1)
- out32r( PCIX0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */
- out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 1 ); /* Enable host config */
+ out32r( PCIL0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
+ out32r( PCIL0_BRDGOPT2, in32(PCIL0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
+#elif defined(PCIL0_BRDGOPT1)
+ out32r( PCIL0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */
+ out32r( PCIL0_BRDGOPT2, in32(PCIL0_BRDGOPT2) | 1 ); /* Enable host config */
#endif
/*--------------------------------------------------------------------------+
* PCI master init: default is one 256MB region for PCI memory:
- * 0x3_00000000 - 0x3_0FFFFFFF ==> CFG_PCI_MEMBASE
+ * 0x3_00000000 - 0x3_0FFFFFFF ==> CONFIG_SYS_PCI_MEMBASE
*--------------------------------------------------------------------------*/
-#if defined(CFG_PCI_MASTER_INIT)
+#if defined(CONFIG_SYS_PCI_MASTER_INIT)
pci_master_init(hose); /* Let board setup pci master */
#else
- out32r( PCIX0_POM0SA, 0 ); /* disable */
- out32r( PCIX0_POM1SA, 0 ); /* disable */
- out32r( PCIX0_POM2SA, 0 ); /* disable */
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
- out32r( PCIX0_POM0LAL, 0x10000000 );
- out32r( PCIX0_POM0LAH, 0x0000000c );
+ out32r( PCIL0_POM0SA, 0 ); /* disable */
+ out32r( PCIL0_POM1SA, 0 ); /* disable */
+ out32r( PCIL0_POM2SA, 0 ); /* disable */
+#if defined(CONFIG_440SPE)
+ out32r( PCIL0_POM0LAL, 0x10000000 );
+ out32r( PCIL0_POM0LAH, 0x0000000c );
+#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
+ out32r( PCIL0_POM0LAL, 0x20000000 );
+ out32r( PCIL0_POM0LAH, 0x0000000c );
#else
- out32r( PCIX0_POM0LAL, 0x00000000 );
- out32r( PCIX0_POM0LAH, 0x00000003 );
+ out32r( PCIL0_POM0LAL, 0x00000000 );
+ out32r( PCIL0_POM0LAH, 0x00000003 );
#endif
- out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE );
- out32r( PCIX0_POM0PCIAH, 0x00000000 );
- out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
- out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 );
+ out32r( PCIL0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE );
+ out32r( PCIL0_POM0PCIAH, 0x00000000 );
+ out32r( PCIL0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
+ out32r( PCIL0_STS, in32r( PCIL0_STS ) & ~0x0000fff8 );
#endif
/*--------------------------------------------------------------------------+
#endif
#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \
!defined(CONFIG_440EPX) && !defined(CONFIG_440GRX)
- out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER);
+ out16r( PCIL0_CMD, in16r( PCIL0_CMD ) | PCI_COMMAND_MASTER);
#endif
hose->last_busno = pci_hose_scan(hose);
}
int busno;
busno = pci_440_init (&ppc440_hose);
-#if defined(CONFIG_440SPE) || \
- defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#if (defined(CONFIG_440SPE) || \
+ defined(CONFIG_460EX) || defined(CONFIG_460GT)) && \
+ !defined(CONFIG_PCI_DISABLE_PCIE)
pcie_setup_hoses(busno + 1);
#endif
}
projects / platform / kernel / u-boot.git / blobdiff