#define CALC_ODT_RW(n) (CALC_ODT_R(n) | CALC_ODT_W(n))
/* Defines for the Read Cycle Delay test */
-#define NUMMEMTESTS 8
-#define NUMMEMWORDS 8
+#define NUMMEMTESTS 8
+#define NUMMEMWORDS 8
+#define NUMLOOPS 256 /* memory test loops */
-#define CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
+#undef CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
/*
* This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory
#ifdef CONFIG_ADD_RAM_INFO
void board_add_ram_info(int use_default)
{
+ PPC440_SYS_INFO board_cfg;
+ u32 val;
+
if (is_ecc_enabled())
- puts(" (ECC enabled)");
+ puts(" (ECC");
else
- puts(" (ECC not enabled)");
+ puts(" (ECC not");
+
+ get_sys_info(&board_cfg);
+
+ mfsdr(SDR0_DDR0, val);
+ val = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(val), 1);
+ printf(" enabled, %d MHz", (val * 2) / 1000000);
+
+ mfsdram(SDRAM_MMODE, val);
+ val = (val & SDRAM_MMODE_DCL_MASK) >> 4;
+ printf(", CL%d)", val);
}
#endif
else
cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
+ debug("cycle_time=%d [10 picoseconds]\n", cycle_time);
if (cycle_time > (calc_cycle_time + 10)) {
/*
mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(sdr_ddrpll), 1);
+ debug("sdram_freq=%d\n", sdram_freq);
/*------------------------------------------------------------------
* Handle the timing. We need to find the worst case timing of all
/* t_wr_ns = max(t_wr_ns, (unsigned long)dimm_spd[dimm_num][36] >> 2); */ /* not used in this loop. */
cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18);
+ debug("cas_bit[SPD byte 18]=%02x\n", cas_bit);
/* For a particular DIMM, grab the three CAS values it supports */
for (cas_index = 0; cas_index < 3; cas_index++) {
if ((tcyc_reg & 0x0F) >= 10) {
if ((tcyc_reg & 0x0F) == 0x0D) {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
} else {
printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
"in slot %d\n", (unsigned int)dimm_num);
}
} else {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) +
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
}
+ debug("cas_index=%d: cycle_time_ns_x_100=%d\n", cas_index,
+ cycle_time_ns_x_100[cas_index]);
}
/* The rest of this routine determines if CAS 2.0, 2.5, 3.0, 4.0 and 5.0 are */
* Bit 7 6 5 4 3 2 1 0
* TBD 4.0 3.5 3.0 2.5 2.0 1.5 1.0
*/
- if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_3_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_2_5_available = FALSE;
}
- if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
* Bit 7 6 5 4 3 2 1 0
* TBD 6.0 5.0 4.0 3.0 2.0 TBD TBD
*/
- if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_5_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100) + 10;
cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100) + 10;
cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100) + 10;
+ debug("cycle_3_0_clk=%d\n", cycle_3_0_clk);
+ debug("cycle_4_0_clk=%d\n", cycle_4_0_clk);
+ debug("cycle_5_0_clk=%d\n", cycle_5_0_clk);
if (sdram_ddr1 == TRUE) { /* DDR1 */
if ((cas_2_0_available == TRUE) && (sdram_freq <= cycle_2_0_clk)) {
hang();
}
} else { /* DDR2 */
+ debug("cas_3_0_available=%d\n", cas_3_0_available);
+ debug("cas_4_0_available=%d\n", cas_4_0_available);
+ debug("cas_5_0_available=%d\n", cas_5_0_available);
if ((cas_3_0_available == TRUE) && (sdram_freq <= cycle_3_0_clk)) {
mmode |= SDRAM_MMODE_DCL_DDR2_3_0_CLK;
*selected_cas = DDR_CAS_3;
return ecc;
}
+static void blank_string(int size)
+{
+ int i;
+
+ for (i=0; i<size; i++)
+ putc('\b');
+ for (i=0; i<size; i++)
+ putc(' ');
+ for (i=0; i<size; i++)
+ putc('\b');
+}
+
#ifdef CONFIG_DDR_ECC
/*-----------------------------------------------------------------------------+
* program_ecc.
unsigned long end_address;
unsigned long address_increment;
unsigned long mcopt1;
- char str[] = "ECC generation...";
- int i;
+ char str[] = "ECC generation -";
+ char slash[] = "\\|/-\\|/-";
+ int loop = 0;
+ int loopi = 0;
current_address = start_address;
mfsdram(SDRAM_MCOPT1, mcopt1);
while (current_address < end_address) {
*((unsigned long *)current_address) = 0x00000000;
current_address += address_increment;
+
+ if ((loop++ % (2 << 20)) == 0) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+ }
}
+
} else {
/* ECC bit set method for cached memory */
dcbz_area(start_address, num_bytes);
dflush();
}
- for (i=0; i<strlen(str); i++)
- putc('\b');
+
+ blank_string(strlen(str));
sync();
eieio();
#endif
}
-static u32 short_mem_test(void)
+static int short_mem_test(void)
{
u32 *membase;
u32 bxcr_num;
0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
{0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55} };
+ int l;
for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) {
mfsdram(SDRAM_MB0CF + (bxcr_num << 2), bxcf);
/* Banks enabled */
if ((bxcf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
-
/* Bank is enabled */
- membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
/*------------------------------------------------------------------
* Run the short memory test.
*-----------------------------------------------------------------*/
+ membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
+
for (i = 0; i < NUMMEMTESTS; i++) {
for (j = 0; j < NUMMEMWORDS; j++) {
membase[j] = test[i][j];
ppcDcbf((u32)&(membase[j]));
}
sync();
- for (j = 0; j < NUMMEMWORDS; j++) {
- if (membase[j] != test[i][j]) {
+ for (l=0; l<NUMLOOPS; l++) {
+ for (j = 0; j < NUMMEMWORDS; j++) {
+ if (membase[j] != test[i][j]) {
+ ppcDcbf((u32)&(membase[j]));
+ return 0;
+ }
ppcDcbf((u32)&(membase[j]));
- break;
}
- ppcDcbf((u32)&(membase[j]));
+ sync();
}
- sync();
- if (j < NUMMEMWORDS)
- break;
}
- if (i < NUMMEMTESTS)
- break;
} /* if bank enabled */
} /* for bxcf_num */
- return bxcr_num;
+ return 1;
}
#ifndef HARD_CODED_DQS
*-----------------------------------------------------------------------------*/
static void DQS_calibration_process(void)
{
- unsigned long ecc_temp;
unsigned long rfdc_reg;
unsigned long rffd;
unsigned long rqdc_reg;
unsigned long rqfd;
- unsigned long bxcr_num;
unsigned long val;
long rqfd_average;
long rffd_average;
long max_end;
unsigned char fail_found;
unsigned char pass_found;
+ u32 rqfd_start;
+ char str[] = "Auto calibration -";
+ char slash[] = "\\|/-\\|/-";
+ int loopi = 0;
/*------------------------------------------------------------------
* Test to determine the best read clock delay tuning bits.
* we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed),
* from experimentation it is safe to say you will always have a failure.
*-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, ecc_temp);
- ecc_temp &= SDRAM_MCOPT1_MCHK_MASK;
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) |
- SDRAM_MCOPT1_MCHK_NON);
+
+ /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
+ rqfd_start = 64; /* test-only: don't know if this is the _best_ start value */
+
+ puts(str);
+
+calibration_loop:
+ mfsdram(SDRAM_RQDC, rqdc_reg);
+ mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
+ SDRAM_RQDC_RQFD_ENCODE(rqfd_start));
max_start = 0;
min_end = 0;
fail_found = FALSE;
pass_found = FALSE;
- /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
- /* rqdc_reg = mfsdram(SDRAM_RQDC) & ~(SDRAM_RQDC_RQFD_MASK); */
-
/*
* get the delay line calibration register value
*/
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
}
}
+ rqfd_average = ((max_start + max_end) >> 1);
+
/*------------------------------------------------------------------
* Make sure we found the valid read passing window. Halt if not
*-----------------------------------------------------------------*/
if (window_found == FALSE) {
- printf("ERROR: Cannot determine a common read delay for the "
+ if (rqfd_start < SDRAM_RQDC_RQFD_MAX) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+
+ /* try again from with a different RQFD start value */
+ rqfd_start++;
+ goto calibration_loop;
+ }
+
+ printf("\nERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
hang();
}
- rqfd_average = ((max_start + max_end) >> 1);
+ blank_string(strlen(str));
if (rqfd_average < 0)
rqfd_average = 0;
if (rqfd_average > SDRAM_RQDC_RQFD_MAX)
rqfd_average = SDRAM_RQDC_RQFD_MAX;
- /*------------------------------------------------------------------
- * Restore the ECC variable to what it originally was
- *-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) | ecc_temp);
-
mtsdram(SDRAM_RQDC,
(rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
SDRAM_RQDC_RQFD_ENCODE(rqfd_average));
projects / platform / kernel / u-boot.git / blobdiff