#endif
#include <common.h>
+#include <command.h>
#include <ppc4xx.h>
#include <i2c.h>
#include <asm/io.h>
#if defined(CONFIG_SPD_EEPROM) && \
(defined(CONFIG_440SP) || defined(CONFIG_440SPE))
+/*-----------------------------------------------------------------------------+
+ * Defines
+ *-----------------------------------------------------------------------------*/
#ifndef TRUE
-#define TRUE 1
+#define TRUE 1
#endif
#ifndef FALSE
-#define FALSE 0
+#define FALSE 0
#endif
#define SDRAM_DDR1 1
#define SDRAM_DDR2 2
#define SDRAM_NONE 0
-#define MAXDIMMS 2
-#define MAXRANKS 4
+#define MAXDIMMS 2
+#define MAXRANKS 4
#define MAXBXCF 4
#define MAX_SPD_BYTES 256 /* Max number of bytes on the DIMM's SPD EEPROM */
#define MULDIV64(m1, m2, d) (u32)(((u64)(m1) * (u64)(m2)) / (u64)(d))
-#if defined(DEBUG)
-static void ppc440sp_sdram_register_dump(void);
-#endif
+#define CMD_NOP (7 << 19)
+#define CMD_PRECHARGE (2 << 19)
+#define CMD_REFRESH (1 << 19)
+#define CMD_EMR (0 << 19)
+#define CMD_READ (5 << 19)
+#define CMD_WRITE (4 << 19)
+
+#define SELECT_MR (0 << 16)
+#define SELECT_EMR (1 << 16)
+#define SELECT_EMR2 (2 << 16)
+#define SELECT_EMR3 (3 << 16)
+
+/* MR */
+#define DLL_RESET 0x00000100
+
+#define WRITE_RECOV_2 (1 << 9)
+#define WRITE_RECOV_3 (2 << 9)
+#define WRITE_RECOV_4 (3 << 9)
+#define WRITE_RECOV_5 (4 << 9)
+#define WRITE_RECOV_6 (5 << 9)
+
+#define BURST_LEN_4 0x00000002
+
+/* EMR */
+#define ODT_0_OHM 0x00000000
+#define ODT_50_OHM 0x00000044
+#define ODT_75_OHM 0x00000004
+#define ODT_150_OHM 0x00000040
+
+#define ODS_FULL 0x00000000
+#define ODS_REDUCED 0x00000002
+
+/* defines for ODT (On Die Termination) of the 440SP(e) DDR2 controller */
+#define ODT_EB0R (0x80000000 >> 8)
+#define ODT_EB0W (0x80000000 >> 7)
+#define CALC_ODT_R(n) (ODT_EB0R << (n << 1))
+#define CALC_ODT_W(n) (ODT_EB0W << (n << 1))
+#define CALC_ODT_RW(n) (CALC_ODT_R(n) | CALC_ODT_W(n))
-/*-----------------------------------------------------------------------------+
- * Defines
- *-----------------------------------------------------------------------------*/
/* Defines for the Read Cycle Delay test */
-#define NUMMEMTESTS 8
-#define NUMMEMWORDS 8
+#define NUMMEMTESTS 8
+#define NUMMEMWORDS 8
+#define NUMLOOPS 64 /* memory test loops */
+
+#undef CONFIG_ECC_ERROR_RESET /* test-only: see description below, at check_ecc() */
+
+/*
+ * This DDR2 setup code can dynamically setup the TLB entries for the DDR2 memory
+ * region. Right now the cache should still be disabled in U-Boot because of the
+ * EMAC driver, that need it's buffer descriptor to be located in non cached
+ * memory.
+ *
+ * If at some time this restriction doesn't apply anymore, just define
+ * CFG_ENABLE_SDRAM_CACHE in the board config file and this code should setup
+ * everything correctly.
+ */
+#ifdef CFG_ENABLE_SDRAM_CACHE
+#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */
+#else
+#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */
+#endif
+
+/*
+ * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed
+ */
+void __spd_ddr_init_hang (void)
+{
+ hang ();
+}
+void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang")));
+
+/*
+ * To provide an interface for board specific config values in this common
+ * DDR setup code, we implement he "weak" default functions here. They return
+ * the default value back to the caller.
+ *
+ * Please see include/configs/yucca.h for an example fora board specific
+ * implementation.
+ */
+u32 __ddr_wrdtr(u32 default_val)
+{
+ return default_val;
+}
+u32 ddr_wrdtr(u32) __attribute__((weak, alias("__ddr_wrdtr")));
+
+u32 __ddr_clktr(u32 default_val)
+{
+ return default_val;
+}
+u32 ddr_clktr(u32) __attribute__((weak, alias("__ddr_clktr")));
+
/* Private Structure Definitions */
* Prototypes
*-----------------------------------------------------------------------------*/
static unsigned long sdram_memsize(void);
-void program_tlb(u32 start, u32 size);
static void get_spd_info(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks);
static void program_mode(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks,
- ddr_cas_id_t *selected_cas);
+ ddr_cas_id_t *selected_cas,
+ int *write_recovery);
static void program_tr(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks);
static void program_initplr(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks,
- ddr_cas_id_t selected_cas);
+ ddr_cas_id_t selected_cas,
+ int write_recovery);
static unsigned long is_ecc_enabled(void);
+#ifdef CONFIG_DDR_ECC
static void program_ecc(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
- unsigned long num_dimm_banks);
+ unsigned long num_dimm_banks,
+ unsigned long tlb_word2_i_value);
static void program_ecc_addr(unsigned long start_address,
- unsigned long num_bytes);
-
-#ifdef HARD_CODED_DQS /* calibration test with hardvalues */
-static void test(void);
-#else
-static void DQS_calibration_process(void);
+ unsigned long num_bytes,
+ unsigned long tlb_word2_i_value);
#endif
static void program_DQS_calibration(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks);
+#ifdef HARD_CODED_DQS /* calibration test with hardvalues */
+static void test(void);
+#else
+static void DQS_calibration_process(void);
+#endif
+static void ppc440sp_sdram_register_dump(void);
+int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+void dcbz_area(u32 start_address, u32 num_bytes);
+void dflush(void);
static u32 mfdcr_any(u32 dcr)
{
}
}
-static void wait_ddr_idle(void)
-{
- u32 val;
-
- do {
- mfsdram(SDRAM_MCSTAT, val);
- } while ((val & SDRAM_MCSTAT_IDLE_MASK) == SDRAM_MCSTAT_IDLE_NOT);
-}
-
static unsigned char spd_read(uchar chip, uint addr)
{
unsigned char data[2];
&& ((mcopt2 & SDRAM_MCOPT2_SREN_MASK) == SDRAM_MCOPT2_SREN_EXIT)
&& ((mcstat & (SDRAM_MCSTAT_MIC_MASK | SDRAM_MCSTAT_SRMS_MASK))
== (SDRAM_MCSTAT_MIC_COMP | SDRAM_MCSTAT_SRMS_NOT_SF))) {
- for (i = 0; i < 4; i++) {
+ for (i = 0; i < MAXBXCF; i++) {
mfsdram(SDRAM_MB0CF + (i << 2), mb0cf);
/* Banks enabled */
if ((mb0cf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
* .data sections. It also cannot call routines that require these sections.
*-----------------------------------------------------------------------------*/
/*-----------------------------------------------------------------------------
- * Function: initdram
+ * Function: initdram
* Description: Configures SDRAM memory banks for DDR operation.
- * Auto Memory Configuration option reads the DDR SDRAM EEPROMs
- * via the IIC bus and then configures the DDR SDRAM memory
- * banks appropriately. If Auto Memory Configuration is
- * not used, it is assumed that no DIMM is plugged
+ * Auto Memory Configuration option reads the DDR SDRAM EEPROMs
+ * via the IIC bus and then configures the DDR SDRAM memory
+ * banks appropriately. If Auto Memory Configuration is
+ * not used, it is assumed that no DIMM is plugged
*-----------------------------------------------------------------------------*/
long int initdram(int board_type)
{
+ unsigned char iic0_dimm_addr[] = SPD_EEPROM_ADDRESS;
unsigned char spd0[MAX_SPD_BYTES];
unsigned char spd1[MAX_SPD_BYTES];
unsigned char *dimm_spd[MAXDIMMS];
unsigned long dimm_populated[MAXDIMMS];
- unsigned char iic0_dimm_addr[MAXDIMMS];
unsigned long num_dimm_banks; /* on board dimm banks */
unsigned long val;
ddr_cas_id_t selected_cas;
+ int write_recovery;
unsigned long dram_size = 0;
num_dimm_banks = sizeof(iic0_dimm_addr);
dimm_spd[1] = spd1;
/*------------------------------------------------------------------
- * Set up an array of iic0 dimm addresses.
- *-----------------------------------------------------------------*/
- iic0_dimm_addr[0] = IIC0_DIMM0_ADDR;
- iic0_dimm_addr[1] = IIC0_DIMM1_ADDR;
-
- /*------------------------------------------------------------------
* Reset the DDR-SDRAM controller.
*-----------------------------------------------------------------*/
- mtsdr(SDR0_SRST, 0x00200000);
+ mtsdr(SDR0_SRST, (0x80000000 >> 10));
mtsdr(SDR0_SRST, 0x00000000);
/*
/*------------------------------------------------------------------
* Program SDRAM mode register.
*-----------------------------------------------------------------*/
- program_mode(dimm_populated, iic0_dimm_addr, num_dimm_banks, &selected_cas);
+ program_mode(dimm_populated, iic0_dimm_addr, num_dimm_banks,
+ &selected_cas, &write_recovery);
/*------------------------------------------------------------------
* Set the SDRAM Write Data/DM/DQS Clock Timing Reg
*-----------------------------------------------------------------*/
mfsdram(SDRAM_WRDTR, val);
mtsdram(SDRAM_WRDTR, (val & ~(SDRAM_WRDTR_LLWP_MASK | SDRAM_WRDTR_WTR_MASK)) |
- (SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_90_DEG_ADV));
+ ddr_wrdtr(SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_90_DEG_ADV));
/*------------------------------------------------------------------
* Set the SDRAM Clock Timing Register
*-----------------------------------------------------------------*/
mfsdram(SDRAM_CLKTR, val);
- mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) | SDRAM_CLKTR_CLKP_0_DEG);
+ mtsdram(SDRAM_CLKTR, (val & ~SDRAM_CLKTR_CLKP_MASK) |
+ ddr_clktr(SDRAM_CLKTR_CLKP_0_DEG));
/*------------------------------------------------------------------
* Program the BxCF registers.
(val & ~(SDRAM_MEMODE_DIC_MASK | SDRAM_MEMODE_DLL_MASK |
SDRAM_MEMODE_RTT_MASK | SDRAM_MEMODE_DQS_MASK)) |
(SDRAM_MEMODE_DIC_NORMAL | SDRAM_MEMODE_DLL_ENABLE
- | SDRAM_MEMODE_RTT_75OHM | SDRAM_MEMODE_DQS_ENABLE));
+ | SDRAM_MEMODE_RTT_150OHM | SDRAM_MEMODE_DQS_ENABLE));
/*------------------------------------------------------------------
* Program Initialization preload registers.
*-----------------------------------------------------------------*/
program_initplr(dimm_populated, iic0_dimm_addr, num_dimm_banks,
- selected_cas);
+ selected_cas, write_recovery);
/*------------------------------------------------------------------
* Delay to ensure 200usec have elapsed since reset.
dram_size = sdram_memsize();
/* and program tlb entries for this size (dynamic) */
- program_tlb(0, dram_size);
-#if 1 /* TODO: ECC support will come later */
- /*------------------------------------------------------------------
- * If ecc is enabled, initialize the parity bits.
- *-----------------------------------------------------------------*/
- program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks);
-#endif
+ /*
+ * Program TLB entries with caches enabled, for best performace
+ * while auto-calibrating and ECC generation
+ */
+ program_tlb(0, 0, dram_size, 0);
/*------------------------------------------------------------------
* DQS calibration.
*-----------------------------------------------------------------*/
program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks);
-#ifdef DEBUG
- ppc440sp_sdram_register_dump();
+#ifdef CONFIG_DDR_ECC
+ /*------------------------------------------------------------------
+ * If ecc is enabled, initialize the parity bits.
+ *-----------------------------------------------------------------*/
+ program_ecc(dimm_populated, iic0_dimm_addr, num_dimm_banks, 0);
#endif
+ /*
+ * Now after initialization (auto-calibration and ECC generation)
+ * remove the TLB entries with caches enabled and program again with
+ * desired cache functionality
+ */
+ remove_tlb(0, dram_size);
+ program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE);
+
+ ppc440sp_sdram_register_dump();
+
return dram_size;
}
if (dimm_found == FALSE) {
printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
#ifdef CONFIG_ADD_RAM_INFO
void board_add_ram_info(int use_default)
{
- if (is_ecc_enabled())
- puts(" (ECC enabled)");
- else
- puts(" (ECC not enabled)");
+ PPC440_SYS_INFO board_cfg;
+ u32 val;
+
+ if (is_ecc_enabled())
+ puts(" (ECC");
+ else
+ puts(" (ECC not");
+
+ get_sys_info(&board_cfg);
+
+ mfsdr(SDR0_DDR0, val);
+ val = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(val), 1);
+ printf(" enabled, %d MHz", (val * 2) / 1000000);
+
+ mfsdram(SDRAM_MMODE, val);
+ val = (val & SDRAM_MMODE_DCL_MASK) >> 4;
+ printf(", CL%d)", val);
}
#endif
"slot %d.\n", (unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 2:
printf("ERROR: EDO DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 3:
printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 4:
printf("ERROR: SDRAM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 5:
printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 6:
printf("ERROR: SGRAM DIMM detected in slot %d.\n",
(unsigned int)dimm_num);
printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
case 7:
debug("DIMM slot %d: DDR1 SDRAM detected\n", dimm_num);
(unsigned int)dimm_num);
printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
}
}
&& (dimm_populated[dimm_num] != SDRAM_NONE)
&& (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) {
printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
*-----------------------------------------------------------------*/
get_sys_info(&board_cfg);
- mfsdr(sdr_ddr0, sdr_ddrpll);
+ mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
/*
else
cycle_time = (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
+ debug("cycle_time=%d [10 picoseconds]\n", cycle_time);
if (cycle_time > (calc_cycle_time + 10)) {
/*
(unsigned int)(calc_cycle_time*10));
printf("Replace the DIMM, or change DDR frequency via "
"strapping bits.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
"slot %d is not supported.\n", dimm_rank, dimm_num);
printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
} else
total_rank += dimm_rank;
}
"for all slots.\n", (unsigned int)total_rank);
printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS);
printf("Remove one of the DIMM modules.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
}
printf("This DIMM is 5.0 Volt/TTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x01:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is LVTTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x02:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is 1.5 Volt.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x03:
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("This DIMM is 3.3 Volt/TTL.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
case 0x04:
/* 2.5 Voltage only for DDR1 */
printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n");
printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n",
(unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
break;
}
}
unsigned long ddrtype;
unsigned long val;
+#ifdef CONFIG_DDR_ECC
ecc_enabled = TRUE;
+#else
+ ecc_enabled = FALSE;
+#endif
dimm_32bit = FALSE;
dimm_64bit = FALSE;
buf0 = FALSE;
if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) {
if (buf0 != buf1) {
printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n");
- hang();
+ spd_ddr_init_hang ();
}
}
if ((dimm_64bit == TRUE) && (dimm_32bit == TRUE)) {
printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n");
- hang();
+ spd_ddr_init_hang ();
}
else if ((dimm_64bit == TRUE) && (dimm_32bit == FALSE)) {
mcopt1 |= SDRAM_MCOPT1_DMWD_64;
mcopt1 |= SDRAM_MCOPT1_DMWD_32;
} else {
printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
if (ecc_enabled == TRUE)
dimm_type = SDRAM_DDR1;
}
- total_rank += dimm_rank;
- total_dimm ++;
+ total_rank += dimm_rank;
+ total_dimm++;
if ((dimm_num == 0) && (total_dimm == 1))
firstSlot = TRUE;
else
codt |= SDRAM_CODT_DQS_1_8_V_DDR2;
if ((total_dimm == 1) && (firstSlot == TRUE)) {
if (total_rank == 1) {
- codt |= 0x00800000;
- modt0 = 0x01000000;
+ codt |= CALC_ODT_R(0);
+ modt0 = CALC_ODT_W(0);
modt1 = 0x00000000;
modt2 = 0x00000000;
modt3 = 0x00000000;
}
if (total_rank == 2) {
- codt |= 0x02800000;
- modt0 = 0x06000000;
- modt1 = 0x01800000;
+ codt |= CALC_ODT_R(0) | CALC_ODT_R(1);
+ modt0 = CALC_ODT_W(0);
+ modt1 = CALC_ODT_W(0);
modt2 = 0x00000000;
modt3 = 0x00000000;
}
- } else {
+ } else if ((total_dimm == 1) && (firstSlot != TRUE)) {
if (total_rank == 1) {
- codt |= 0x00800000;
- modt0 = 0x01000000;
+ codt |= CALC_ODT_R(2);
+ modt0 = 0x00000000;
modt1 = 0x00000000;
- modt2 = 0x00000000;
+ modt2 = CALC_ODT_W(2);
modt3 = 0x00000000;
}
if (total_rank == 2) {
- codt |= 0x02800000;
- modt0 = 0x06000000;
- modt1 = 0x01800000;
- modt2 = 0x00000000;
- modt3 = 0x00000000;
+ codt |= CALC_ODT_R(2) | CALC_ODT_R(3);
+ modt0 = 0x00000000;
+ modt1 = 0x00000000;
+ modt2 = CALC_ODT_W(2);
+ modt3 = CALC_ODT_W(2);
}
}
if (total_dimm == 2) {
if (total_rank == 2) {
- codt |= 0x08800000;
- modt0 = 0x18000000;
+ codt |= CALC_ODT_R(0) | CALC_ODT_R(2);
+ modt0 = CALC_ODT_RW(2);
modt1 = 0x00000000;
- modt2 = 0x01800000;
+ modt2 = CALC_ODT_RW(0);
modt3 = 0x00000000;
}
if (total_rank == 4) {
- codt |= 0x2a800000;
- modt0 = 0x18000000;
- modt1 = 0x18000000;
- modt2 = 0x01800000;
- modt3 = 0x01800000;
+ codt |= CALC_ODT_R(0) | CALC_ODT_R(1) |
+ CALC_ODT_R(2) | CALC_ODT_R(3);
+ modt0 = CALC_ODT_RW(2);
+ modt1 = 0x00000000;
+ modt2 = CALC_ODT_RW(0);
+ modt3 = 0x00000000;
}
}
- } else {
+ } else {
codt |= SDRAM_CODT_DQS_2_5_V_DDR1;
modt0 = 0x00000000;
modt1 = 0x00000000;
static void program_initplr(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks,
- ddr_cas_id_t selected_cas)
+ ddr_cas_id_t selected_cas,
+ int write_recovery)
{
- unsigned long MR_CAS_value = 0;
+ u32 cas = 0;
+ u32 odt = 0;
+ u32 ods = 0;
+ u32 mr;
+ u32 wr;
+ u32 emr;
+ u32 emr2;
+ u32 emr3;
+ int dimm_num;
+ int total_dimm = 0;
/******************************************************
** Assumption: if more than one DIMM, all DIMMs are the same
- ** as already checked in check_memory_type
+ ** as already checked in check_memory_type
******************************************************/
if ((dimm_populated[0] == SDRAM_DDR1) || (dimm_populated[1] == SDRAM_DDR1)) {
mtsdram(SDRAM_INITPLR7, 0x81000062);
} else if ((dimm_populated[0] == SDRAM_DDR2) || (dimm_populated[1] == SDRAM_DDR2)) {
switch (selected_cas) {
- /*
- * The CAS latency is a field of the Mode Reg
- * that need to be set from caller input.
- * CAS bits in Mode Reg are starting at bit 4 at least for the Micron DDR2
- * this is the reason of the shift.
- */
case DDR_CAS_3:
- MR_CAS_value = 3 << 4;
+ cas = 3 << 4;
break;
case DDR_CAS_4:
- MR_CAS_value = 4 << 4;
+ cas = 4 << 4;
break;
case DDR_CAS_5:
- MR_CAS_value = 5 << 4;
+ cas = 5 << 4;
+ break;
+ default:
+ printf("ERROR: ucode error on selected_cas value %d", selected_cas);
+ spd_ddr_init_hang ();
+ break;
+ }
+
+#if 0
+ /*
+ * ToDo - Still a problem with the write recovery:
+ * On the Corsair CM2X512-5400C4 module, setting write recovery
+ * in the INITPLR reg to the value calculated in program_mode()
+ * results in not correctly working DDR2 memory (crash after
+ * relocation).
+ *
+ * So for now, set the write recovery to 3. This seems to work
+ * on the Corair module too.
+ *
+ * 2007-03-01, sr
+ */
+ switch (write_recovery) {
+ case 3:
+ wr = WRITE_RECOV_3;
+ break;
+ case 4:
+ wr = WRITE_RECOV_4;
+ break;
+ case 5:
+ wr = WRITE_RECOV_5;
+ break;
+ case 6:
+ wr = WRITE_RECOV_6;
break;
default:
- printf("ERROR: ucode error on selected_cas value %d", (unsigned char)selected_cas);
- hang();
+ printf("ERROR: write recovery not support (%d)", write_recovery);
+ spd_ddr_init_hang ();
break;
}
+#else
+ wr = WRITE_RECOV_3; /* test-only, see description above */
+#endif
+
+ for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++)
+ if (dimm_populated[dimm_num] != SDRAM_NONE)
+ total_dimm++;
+ if (total_dimm == 1) {
+ odt = ODT_150_OHM;
+ ods = ODS_FULL;
+ } else if (total_dimm == 2) {
+ odt = ODT_75_OHM;
+ ods = ODS_REDUCED;
+ } else {
+ printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm);
+ spd_ddr_init_hang ();
+ }
- mtsdram(SDRAM_INITPLR0, 0xB5380000); /* NOP */
- mtsdram(SDRAM_INITPLR1, 0x82100400); /* precharge 8 DDR clock cycle */
- mtsdram(SDRAM_INITPLR2, 0x80820000); /* EMR2 */
- mtsdram(SDRAM_INITPLR3, 0x80830000); /* EMR3 */
- mtsdram(SDRAM_INITPLR4, 0x80810000); /* EMR DLL ENABLE */
- mtsdram(SDRAM_INITPLR5, 0x80800502 | MR_CAS_value); /* MR w/ DLL reset */
- mtsdram(SDRAM_INITPLR6, 0x82100400); /* precharge 8 DDR clock cycle */
- mtsdram(SDRAM_INITPLR7, 0x8a080000); /* Refresh 50 DDR clock cycle */
- mtsdram(SDRAM_INITPLR8, 0x8a080000); /* Refresh 50 DDR clock cycle */
- mtsdram(SDRAM_INITPLR9, 0x8a080000); /* Refresh 50 DDR clock cycle */
- mtsdram(SDRAM_INITPLR10, 0x8a080000); /* Refresh 50 DDR clock cycle */
- mtsdram(SDRAM_INITPLR11, 0x80800402 | MR_CAS_value); /* MR w/o DLL reset */
- mtsdram(SDRAM_INITPLR12, 0x80810380); /* EMR OCD Default */
- mtsdram(SDRAM_INITPLR13, 0x80810000); /* EMR OCD Exit */
+ mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas;
+ emr = CMD_EMR | SELECT_EMR | odt | ods;
+ emr2 = CMD_EMR | SELECT_EMR2;
+ emr3 = CMD_EMR | SELECT_EMR3;
+ mtsdram(SDRAM_INITPLR0, 0xB5000000 | CMD_NOP); /* NOP */
+ udelay(1000);
+ mtsdram(SDRAM_INITPLR1, 0x82000400 | CMD_PRECHARGE); /* precharge 8 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR2, 0x80800000 | emr2); /* EMR2 */
+ mtsdram(SDRAM_INITPLR3, 0x80800000 | emr3); /* EMR3 */
+ mtsdram(SDRAM_INITPLR4, 0x80800000 | emr); /* EMR DLL ENABLE */
+ mtsdram(SDRAM_INITPLR5, 0x80800000 | mr | DLL_RESET); /* MR w/ DLL reset */
+ udelay(1000);
+ mtsdram(SDRAM_INITPLR6, 0x82000400 | CMD_PRECHARGE); /* precharge 8 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR7, 0x8a000000 | CMD_REFRESH); /* Refresh 50 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR8, 0x8a000000 | CMD_REFRESH); /* Refresh 50 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR9, 0x8a000000 | CMD_REFRESH); /* Refresh 50 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR10, 0x8a000000 | CMD_REFRESH); /* Refresh 50 DDR clock cycle */
+ mtsdram(SDRAM_INITPLR11, 0x80000000 | mr); /* MR w/o DLL reset */
+ mtsdram(SDRAM_INITPLR12, 0x80800380 | emr); /* EMR OCD Default */
+ mtsdram(SDRAM_INITPLR13, 0x80800000 | emr); /* EMR OCD Exit */
} else {
printf("ERROR: ucode error as unknown DDR type in program_initplr");
- hang();
+ spd_ddr_init_hang ();
}
}
static void program_mode(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
unsigned long num_dimm_banks,
- ddr_cas_id_t *selected_cas)
+ ddr_cas_id_t *selected_cas,
+ int *write_recovery)
{
unsigned long dimm_num;
unsigned long sdram_ddr1;
*-----------------------------------------------------------------*/
get_sys_info(&board_cfg);
- mfsdr(sdr_ddr0, sdr_ddrpll);
+ mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = MULDIV64((board_cfg.freqPLB), SDR0_DDR0_DDRM_DECODE(sdr_ddrpll), 1);
+ debug("sdram_freq=%d\n", sdram_freq);
/*------------------------------------------------------------------
* Handle the timing. We need to find the worst case timing of all
/* t_wr_ns = max(t_wr_ns, (unsigned long)dimm_spd[dimm_num][36] >> 2); */ /* not used in this loop. */
cas_bit = spd_read(iic0_dimm_addr[dimm_num], 18);
+ debug("cas_bit[SPD byte 18]=%02x\n", cas_bit);
/* For a particular DIMM, grab the three CAS values it supports */
for (cas_index = 0; cas_index < 3; cas_index++) {
if ((tcyc_reg & 0x0F) >= 10) {
if ((tcyc_reg & 0x0F) == 0x0D) {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) + 75;
} else {
printf("ERROR: SPD reported Tcyc is incorrect for DIMM "
"in slot %d\n", (unsigned int)dimm_num);
- hang();
+ spd_ddr_init_hang ();
}
} else {
/* Convert from hex to decimal */
- cycle_time_ns_x_100[cas_index] = (((tcyc_reg & 0xF0) >> 4) * 100) +
+ cycle_time_ns_x_100[cas_index] =
+ (((tcyc_reg & 0xF0) >> 4) * 100) +
((tcyc_reg & 0x0F)*10);
}
+ debug("cas_index=%d: cycle_time_ns_x_100=%d\n", cas_index,
+ cycle_time_ns_x_100[cas_index]);
}
/* The rest of this routine determines if CAS 2.0, 2.5, 3.0, 4.0 and 5.0 are */
* Bit 7 6 5 4 3 2 1 0
* TBD 4.0 3.5 3.0 2.5 2.0 1.5 1.0
*/
- if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x40) == 0x40) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_3_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_5_tcyc_ns_x_100 = max(max_2_5_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_2_5_available = FALSE;
}
- if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x04) == 0x04) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_2_0_tcyc_ns_x_100 = max(max_2_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
* Bit 7 6 5 4 3 2 1 0
* TBD 6.0 5.0 4.0 3.0 2.0 TBD TBD
*/
- if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x20) == 0x20) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_5_0_tcyc_ns_x_100 = max(max_5_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_5_0_available = FALSE;
}
- if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x10) == 0x10) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_4_0_tcyc_ns_x_100 = max(max_4_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
cas_4_0_available = FALSE;
}
- if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) && (cycle_time_ns_x_100[cas_index] != 0)) {
- max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100, cycle_time_ns_x_100[cas_index]);
+ if (((cas_bit & 0x08) == 0x08) && (cas_index < 3) &&
+ (cycle_time_ns_x_100[cas_index] != 0)) {
+ max_3_0_tcyc_ns_x_100 = max(max_3_0_tcyc_ns_x_100,
+ cycle_time_ns_x_100[cas_index]);
cas_index++;
} else {
if (cas_index != 0)
mfsdram(SDRAM_MMODE, mmode);
mmode = mmode & ~(SDRAM_MMODE_WR_MASK | SDRAM_MMODE_DCL_MASK);
- cycle_2_0_clk = MULDIV64(ONE_BILLION, 100, max_2_0_tcyc_ns_x_100);
- cycle_2_5_clk = MULDIV64(ONE_BILLION, 100, max_2_5_tcyc_ns_x_100);
- cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100);
- cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100);
- cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100);
+ /* add 10 here because of rounding problems */
+ cycle_2_0_clk = MULDIV64(ONE_BILLION, 100, max_2_0_tcyc_ns_x_100) + 10;
+ cycle_2_5_clk = MULDIV64(ONE_BILLION, 100, max_2_5_tcyc_ns_x_100) + 10;
+ cycle_3_0_clk = MULDIV64(ONE_BILLION, 100, max_3_0_tcyc_ns_x_100) + 10;
+ cycle_4_0_clk = MULDIV64(ONE_BILLION, 100, max_4_0_tcyc_ns_x_100) + 10;
+ cycle_5_0_clk = MULDIV64(ONE_BILLION, 100, max_5_0_tcyc_ns_x_100) + 10;
+ debug("cycle_3_0_clk=%d\n", cycle_3_0_clk);
+ debug("cycle_4_0_clk=%d\n", cycle_4_0_clk);
+ debug("cycle_5_0_clk=%d\n", cycle_5_0_clk);
if (sdram_ddr1 == TRUE) { /* DDR1 */
if ((cas_2_0_available == TRUE) && (sdram_freq <= cycle_2_0_clk)) {
printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n");
printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
} else { /* DDR2 */
+ debug("cas_3_0_available=%d\n", cas_3_0_available);
+ debug("cas_4_0_available=%d\n", cas_4_0_available);
+ debug("cas_5_0_available=%d\n", cas_5_0_available);
if ((cas_3_0_available == TRUE) && (sdram_freq <= cycle_3_0_clk)) {
mmode |= SDRAM_MMODE_DCL_DDR2_3_0_CLK;
*selected_cas = DDR_CAS_3;
} else {
printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n");
printf("Only DIMMs DDR2 with CAS latencies of 3.0, 4.0, and 5.0 are supported.\n");
- printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n");
- hang();
+ printf("Make sure the PLB speed is within the supported range of the DIMMs.\n");
+ printf("cas3=%d cas4=%d cas5=%d\n",
+ cas_3_0_available, cas_4_0_available, cas_5_0_available);
+ printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n",
+ sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk);
+ spd_ddr_init_hang ();
}
}
mmode |= SDRAM_MMODE_WR_DDR2_6_CYC;
break;
}
+ *write_recovery = t_wr_clk;
}
+ debug("CAS latency = %d\n", *selected_cas);
+ debug("Write recovery = %d\n", *write_recovery);
+
mtsdram(SDRAM_MMODE, mmode);
}
/*------------------------------------------------------------------
* Set the SDRAM Refresh Timing Register, SDRAM_RTR
*-----------------------------------------------------------------*/
- mfsdr(sdr_ddr0, sdr_ddrpll);
+ mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
max_refresh_rate = 0;
printf("ERROR: DIMM %d unsupported refresh rate/type.\n",
(unsigned int)dimm_num);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
}
*-----------------------------------------------------------------*/
get_sys_info(&board_cfg);
- mfsdr(sdr_ddr0, sdr_ddrpll);
+ mfsdr(SDR0_DDR0, sdr_ddrpll);
sdram_freq = ((board_cfg.freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
/*------------------------------------------------------------------
printf("ERROR: Unsupported value for number of "
"column addresses: %d.\n", (unsigned int)num_col_addr);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
* Set the sizes
*-----------------------------------------------------------------*/
baseadd_size = 0;
- rank_size_bytes = 1024 * 1024 * rank_size_id;
+ rank_size_bytes = 4 * 1024 * 1024 * rank_size_id;
switch (rank_size_id) {
case 0x02:
baseadd_size |= SDRAM_RXBAS_SDSZ_8;
printf("ERROR: Unsupported value for the banksize: %d.\n",
(unsigned int)rank_size_id);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1))
for (i = 0; i < num_ranks; i++) {
mtdcr_any(rank_reg+i+dimm_num+bank_0_populated,
- (rank_base_addr & SDRAM_RXBAS_SDBA_MASK) |
- baseadd_size);
+ (SDRAM_RXBAS_SDBA_ENCODE(rank_base_addr) |
+ baseadd_size));
rank_base_addr += rank_size_bytes;
}
}
ecc = max(ecc, SDRAM_MCOPT1_MCHK_CHK_DECODE(val));
}
- return(ecc);
+ return ecc;
+}
+
+static void blank_string(int size)
+{
+ int i;
+
+ for (i=0; i<size; i++)
+ putc('\b');
+ for (i=0; i<size; i++)
+ putc(' ');
+ for (i=0; i<size; i++)
+ putc('\b');
}
+#ifdef CONFIG_DDR_ECC
/*-----------------------------------------------------------------------------+
* program_ecc.
*-----------------------------------------------------------------------------*/
static void program_ecc(unsigned long *dimm_populated,
unsigned char *iic0_dimm_addr,
- unsigned long num_dimm_banks)
+ unsigned long num_dimm_banks,
+ unsigned long tlb_word2_i_value)
{
unsigned long mcopt1;
unsigned long mcopt2;
&& ((mcstat & (SDRAM_MCSTAT_MIC_MASK | SDRAM_MCSTAT_SRMS_MASK))
== (SDRAM_MCSTAT_MIC_COMP | SDRAM_MCSTAT_SRMS_NOT_SF))) {
- program_ecc_addr(0, sdram_memsize());
+ program_ecc_addr(0, sdram_memsize(), tlb_word2_i_value);
}
}
return;
}
+#ifdef CONFIG_ECC_ERROR_RESET
+/*
+ * Check for ECC errors and reset board upon any error here
+ *
+ * On the Katmai 440SPe eval board, from time to time, the first
+ * lword write access after DDR2 initializazion with ECC checking
+ * enabled, leads to an ECC error. I couldn't find a configuration
+ * without this happening. On my board with the current setup it
+ * happens about 1 from 10 times.
+ *
+ * The ECC modules used for testing are:
+ * - Kingston ValueRAM KVR667D2E5/512 (tested with 1 and 2 DIMM's)
+ *
+ * This has to get fixed for the Katmai and tested for the other
+ * board (440SP/440SPe) that will eventually use this code in the
+ * future.
+ *
+ * 2007-03-01, sr
+ */
+static void check_ecc(void)
+{
+ u32 val;
+
+ mfsdram(SDRAM_ECCCR, val);
+ if (val != 0) {
+ printf("\nECC error: MCIF0_ECCES=%08lx MQ0_ESL=%08lx address=%08lx\n",
+ val, mfdcr(0x4c), mfdcr(0x4e));
+ printf("ECC error occured, resetting board...\n");
+ do_reset(NULL, 0, 0, NULL);
+ }
+}
+#endif
+
+static void wait_ddr_idle(void)
+{
+ u32 val;
+
+ do {
+ mfsdram(SDRAM_MCSTAT, val);
+ } while ((val & SDRAM_MCSTAT_IDLE_MASK) == SDRAM_MCSTAT_IDLE_NOT);
+}
+
/*-----------------------------------------------------------------------------+
* program_ecc_addr.
*-----------------------------------------------------------------------------*/
static void program_ecc_addr(unsigned long start_address,
- unsigned long num_bytes)
+ unsigned long num_bytes,
+ unsigned long tlb_word2_i_value)
{
unsigned long current_address;
unsigned long end_address;
unsigned long address_increment;
unsigned long mcopt1;
+ char str[] = "ECC generation -";
+ char slash[] = "\\|/-\\|/-";
+ int loop = 0;
+ int loopi = 0;
current_address = start_address;
mfsdram(SDRAM_MCOPT1, mcopt1);
eieio();
wait_ddr_idle();
- /* ECC bit set method for non-cached memory */
- if ((mcopt1 & SDRAM_MCOPT1_DMWD_MASK) == SDRAM_MCOPT1_DMWD_32)
- address_increment = 4;
- else
- address_increment = 8;
- end_address = current_address + num_bytes;
+ puts(str);
+ if (tlb_word2_i_value == TLB_WORD2_I_ENABLE) {
+ /* ECC bit set method for non-cached memory */
+ if ((mcopt1 & SDRAM_MCOPT1_DMWD_MASK) == SDRAM_MCOPT1_DMWD_32)
+ address_increment = 4;
+ else
+ address_increment = 8;
+ end_address = current_address + num_bytes;
+
+ while (current_address < end_address) {
+ *((unsigned long *)current_address) = 0x00000000;
+ current_address += address_increment;
+
+ if ((loop++ % (2 << 20)) == 0) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+ }
+ }
- while (current_address < end_address) {
- *((unsigned long *)current_address) = 0x00000000;
- current_address += address_increment;
+ } else {
+ /* ECC bit set method for cached memory */
+ dcbz_area(start_address, num_bytes);
+ dflush();
}
+
+ blank_string(strlen(str));
+
sync();
eieio();
wait_ddr_idle();
+ /* clear ECC error repoting registers */
+ mtsdram(SDRAM_ECCCR, 0xffffffff);
+ mtdcr(0x4c, 0xffffffff);
+
mtsdram(SDRAM_MCOPT1,
- (mcopt1 & ~SDRAM_MCOPT1_MCHK_MASK) | SDRAM_MCOPT1_MCHK_CHK);
+ (mcopt1 & ~SDRAM_MCOPT1_MCHK_MASK) | SDRAM_MCOPT1_MCHK_CHK_REP);
sync();
eieio();
wait_ddr_idle();
+
+#ifdef CONFIG_ECC_ERROR_RESET
+ /*
+ * One write to 0 is enough to trigger this ECC error
+ * (see description above)
+ */
+ out_be32(0, 0x12345678);
+ check_ecc();
+#endif
}
}
+#endif
/*-----------------------------------------------------------------------------+
* program_DQS_calibration.
#endif
}
-static u32 short_mem_test(void)
+static int short_mem_test(void)
{
u32 *membase;
u32 bxcr_num;
0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
{0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55} };
+ int l;
for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) {
mfsdram(SDRAM_MB0CF + (bxcr_num << 2), bxcf);
/* Banks enabled */
if ((bxcf & SDRAM_BXCF_M_BE_MASK) == SDRAM_BXCF_M_BE_ENABLE) {
-
/* Bank is enabled */
- membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
/*------------------------------------------------------------------
* Run the short memory test.
*-----------------------------------------------------------------*/
+ membase = (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num)));
+
for (i = 0; i < NUMMEMTESTS; i++) {
for (j = 0; j < NUMMEMWORDS; j++) {
membase[j] = test[i][j];
ppcDcbf((u32)&(membase[j]));
}
sync();
- for (j = 0; j < NUMMEMWORDS; j++) {
- if (membase[j] != test[i][j]) {
+ for (l=0; l<NUMLOOPS; l++) {
+ for (j = 0; j < NUMMEMWORDS; j++) {
+ if (membase[j] != test[i][j]) {
+ ppcDcbf((u32)&(membase[j]));
+ return 0;
+ }
ppcDcbf((u32)&(membase[j]));
- break;
}
- ppcDcbf((u32)&(membase[j]));
+ sync();
}
- sync();
- if (j < NUMMEMWORDS)
- break;
}
- if (i < NUMMEMTESTS)
- break;
} /* if bank enabled */
} /* for bxcf_num */
- return bxcr_num;
+ return 1;
}
#ifndef HARD_CODED_DQS
*-----------------------------------------------------------------------------*/
static void DQS_calibration_process(void)
{
- unsigned long ecc_temp;
unsigned long rfdc_reg;
unsigned long rffd;
unsigned long rqdc_reg;
unsigned long rqfd;
- unsigned long bxcr_num;
unsigned long val;
long rqfd_average;
long rffd_average;
long max_end;
unsigned char fail_found;
unsigned char pass_found;
+ u32 rqfd_start;
+ char str[] = "Auto calibration -";
+ char slash[] = "\\|/-\\|/-";
+ int loopi = 0;
/*------------------------------------------------------------------
* Test to determine the best read clock delay tuning bits.
* we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed),
* from experimentation it is safe to say you will always have a failure.
*-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, ecc_temp);
- ecc_temp &= SDRAM_MCOPT1_MCHK_MASK;
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) |
- SDRAM_MCOPT1_MCHK_NON);
+
+ /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
+ rqfd_start = 64; /* test-only: don't know if this is the _best_ start value */
+
+ puts(str);
+
+calibration_loop:
+ mfsdram(SDRAM_RQDC, rqdc_reg);
+ mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
+ SDRAM_RQDC_RQFD_ENCODE(rqfd_start));
max_start = 0;
min_end = 0;
fail_found = FALSE;
pass_found = FALSE;
- /* first fix RQDC[RQFD] to an average of 80 degre phase shift to find RFDC[RFFD] */
- /* rqdc_reg = mfsdram(SDRAM_RQDC) & ~(SDRAM_RQDC_RQFD_MASK); */
-
/*
* get the delay line calibration register value
*/
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
}
} /* for rffd */
-
/*------------------------------------------------------------------
* Set the average RFFD value
*-----------------------------------------------------------------*/
*-----------------------------------------------------------------*/
mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd));
- /* do the small memory test */
- bxcr_num = short_mem_test();
-
/*------------------------------------------------------------------
* See if the rffd value passed.
*-----------------------------------------------------------------*/
- if (bxcr_num == MAXBXCF) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0)
}
}
+ rqfd_average = ((max_start + max_end) >> 1);
+
/*------------------------------------------------------------------
* Make sure we found the valid read passing window. Halt if not
*-----------------------------------------------------------------*/
if (window_found == FALSE) {
- printf("ERROR: Cannot determine a common read delay for the "
+ if (rqfd_start < SDRAM_RQDC_RQFD_MAX) {
+ putc('\b');
+ putc(slash[loopi++ % 8]);
+
+ /* try again from with a different RQFD start value */
+ rqfd_start++;
+ goto calibration_loop;
+ }
+
+ printf("\nERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__);
- hang();
+ ppc440sp_sdram_register_dump();
+ spd_ddr_init_hang ();
}
- rqfd_average = ((max_start + max_end) >> 1);
+ blank_string(strlen(str));
if (rqfd_average < 0)
rqfd_average = 0;
if (rqfd_average > SDRAM_RQDC_RQFD_MAX)
rqfd_average = SDRAM_RQDC_RQFD_MAX;
- /*------------------------------------------------------------------
- * Restore the ECC variable to what it originally was
- *-----------------------------------------------------------------*/
- mfsdram(SDRAM_MCOPT1, val);
- mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) | ecc_temp);
-
mtsdram(SDRAM_RQDC,
(rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) |
SDRAM_RQDC_RQFD_ENCODE(rqfd_average));
if (window_found == FALSE) {
printf("ERROR: Cannot determine a common read delay for the "
"DIMM(s) installed.\n");
- hang();
+ spd_ddr_init_hang ();
}
/*------------------------------------------------------------------
dcr_data = mfdcr(SDRAM_R3BAS);
printf(" MQ3_B0BAS = 0x%08X\n", dcr_data);
}
+#else
+static void ppc440sp_sdram_register_dump(void)
+{
+}
#endif
#endif /* CONFIG_SPD_EEPROM */