* Jun Gu, Artesyn Technology, jung@artesyncp.com
* Support for AMCC 440 based on OpenBIOS draminit.c from IBM.
*
- * (C) Copyright 2005
+ * (C) Copyright 2005-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
* MA 02111-1307 USA
*/
+/* define DEBUG for debugging output (obviously ;-)) */
+#if 0
+#define DEBUG
+#endif
+
#include <common.h>
#include <asm/processor.h>
#include <i2c.h>
#define ONE_BILLION 1000000000
+/*
+ * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed
+ */
+void __spd_ddr_init_hang (void)
+{
+ hang ();
+}
+void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang")));
+
/*-----------------------------------------------------------------------------
| Memory Controller Options 0
+-----------------------------------------------------------------------------*/
#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */
#endif
-const unsigned long test[NUMMEMTESTS][NUMMEMWORDS] = {
- {0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
- 0xFFFFFFFF, 0xFFFFFFFF},
- {0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
- 0x00000000, 0x00000000},
- {0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
- 0x55555555, 0x55555555},
- {0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
- 0xAAAAAAAA, 0xAAAAAAAA},
- {0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
- 0x5A5A5A5A, 0x5A5A5A5A},
- {0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
- 0xA5A5A5A5, 0xA5A5A5A5},
- {0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
- 0x55AA55AA, 0x55AA55AA},
- {0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
- 0xAA55AA55, 0xAA55AA55}
-};
-
/* bank_parms is used to sort the bank sizes by descending order */
struct bank_param {
unsigned long cr;
typedef struct bank_param BANKPARMS;
#ifdef CFG_SIMULATE_SPD_EEPROM
-extern unsigned char cfg_simulate_spd_eeprom[128];
+extern const unsigned char cfg_simulate_spd_eeprom[128];
#endif
-void program_tlb(u32 start, u32 size, u32 tlb_word2_i_value);
-unsigned char spd_read(uchar chip, uint addr);
-
-void get_spd_info(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void check_mem_type
-(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void check_volt_type
-(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void program_cfg0(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void program_cfg1(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void program_rtr (unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void program_tr0 (unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
-
-void program_tr1 (void);
-
-void program_ecc (unsigned long num_bytes);
+static unsigned char spd_read(uchar chip, uint addr);
+static void get_spd_info(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void check_mem_type(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void check_volt_type(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void program_cfg0(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void program_cfg1(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void program_rtr(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void program_tr0(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
+static void program_tr1(void);
+
+#ifdef CONFIG_DDR_ECC
+static void program_ecc(unsigned long num_bytes);
+#endif
-unsigned
-long program_bxcr(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks);
+static unsigned long program_bxcr(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks);
/*
* This function is reading data from the DIMM module EEPROM over the SPD bus
* BUG: Don't handle ECC memory
* BUG: A few values in the TR register is currently hardcoded
*/
-
long int spd_sdram(void) {
unsigned char iic0_dimm_addr[] = SPD_EEPROM_ADDRESS;
unsigned long dimm_populated[sizeof(iic0_dimm_addr)];
#ifdef CONFIG_PROG_SDRAM_TLB /* this define should eventually be removed */
/* and program tlb entries for this size (dynamic) */
- program_tlb(0, total_size, MY_TLB_WORD2_I_ENABLE);
+ program_tlb(0, 0, total_size, MY_TLB_WORD2_I_ENABLE);
#endif
/*
*/
while (1) {
mfsdram(mem_mcsts, mcsts);
- if ((mcsts & SDRAM_MCSTS_MRSC) != 0) {
+ if ((mcsts & SDRAM_MCSTS_MRSC) != 0)
break;
- }
}
/*
*/
program_tr1();
+#ifdef CONFIG_DDR_ECC
/*
- * if ECC is enabled, initialize parity bits
+ * If ecc is enabled, initialize the parity bits.
*/
+ program_ecc(total_size);
+#endif
return total_size;
}
-unsigned char spd_read(uchar chip, uint addr)
+static unsigned char spd_read(uchar chip, uint addr)
{
unsigned char data[2];
return 0;
}
-void get_spd_info(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void get_spd_info(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long dimm_found;
if ((num_of_bytes != 0) && (total_size != 0)) {
dimm_populated[dimm_num] = TRUE;
dimm_found = TRUE;
-#if 0
- printf("DIMM slot %lu: populated\n", dimm_num);
-#endif
+ debug("DIMM slot %lu: populated\n", dimm_num);
} else {
dimm_populated[dimm_num] = FALSE;
-#if 0
- printf("DIMM slot %lu: Not populated\n", dimm_num);
-#endif
+ debug("DIMM slot %lu: Not populated\n", dimm_num);
}
}
if (dimm_found == FALSE) {
printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
}
-void check_mem_type(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void check_mem_type(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned char dimm_type;
dimm_type = spd_read(iic0_dimm_addr[dimm_num], 2);
switch (dimm_type) {
case 7:
-#if 0
- printf("DIMM slot %lu: DDR SDRAM detected\n", dimm_num);
-#endif
+ debug("DIMM slot %lu: DDR SDRAM detected\n", dimm_num);
break;
default:
printf("ERROR: Unsupported DIMM detected in slot %lu.\n",
dimm_num);
printf("Only DDR SDRAM DIMMs are supported.\n");
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
break;
}
}
}
}
-
-void check_volt_type(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void check_volt_type(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long voltage_type;
if (voltage_type != 0x04) {
printf("ERROR: DIMM %lu with unsupported voltage level.\n",
dimm_num);
- hang();
+ spd_ddr_init_hang ();
} else {
-#if 0
- printf("DIMM %lu voltage level supported.\n", dimm_num);
-#endif
+ debug("DIMM %lu voltage level supported.\n", dimm_num);
}
break;
}
}
}
-void program_cfg0(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void program_cfg0(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long cfg0;
printf("WARNING: DIMM with datawidth of %lu bits.\n",
data_width);
printf("Only DIMMs with 32 or 64 bit datawidths supported.\n");
- hang();
+ spd_ddr_init_hang ();
}
break;
}
mtsdram(mem_cfg0, cfg0);
}
-void program_cfg1(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void program_cfg1(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long cfg1;
mfsdram(mem_cfg1, cfg1);
mtsdram(mem_cfg1, cfg1);
}
-void program_rtr (unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void program_rtr(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long bus_period_x_10;
get_sys_info(&sys_info);
bus_period_x_10 = ONE_BILLION / (sys_info.freqPLB / 10);
-
for (dimm_num = 0; dimm_num < num_dimm_banks; dimm_num++) {
if (dimm_populated[dimm_num] == TRUE) {
refresh_rate_type = 0x7F & spd_read(iic0_dimm_addr[dimm_num], 12);
mtsdram(mem_rtr, sdram_rtr);
}
-void program_tr0 (unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static void program_tr0(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long tr0;
if ((tcyc_reg & 0x0F) >= 10) {
printf("ERROR: Tcyc incorrect for DIMM in slot %lu\n",
dimm_num);
- hang();
+ spd_ddr_init_hang ();
}
cycle_time_ns_x_10[cas_index] =
printf("ERROR: No supported CAS latency with the installed DIMMs.\n");
printf("Only CAS latencies of 2.0, 2.5, and 3.0 are supported.\n");
printf("Make sure the PLB speed is within the supported range.\n");
- hang();
+ spd_ddr_init_hang ();
}
/*
break;
}
-#if 0
- printf("tr0: %x\n", tr0);
-#endif
+ debug("tr0: %x\n", tr0);
mtsdram(mem_tr0, tr0);
}
-void program_tr1 (void)
+static int short_mem_test(void)
+{
+ unsigned long i, j;
+ unsigned long bxcr_num;
+ unsigned long *membase;
+ const unsigned long test[NUMMEMTESTS][NUMMEMWORDS] = {
+ {0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
+ 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF},
+ {0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
+ 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000},
+ {0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
+ 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555},
+ {0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
+ 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA},
+ {0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
+ 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A},
+ {0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
+ 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5},
+ {0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
+ 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA},
+ {0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
+ 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55}};
+
+ for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) {
+ mtdcr(memcfga, mem_b0cr + (bxcr_num << 2));
+ if ((mfdcr(memcfgd) & SDRAM_BXCR_SDBE) == SDRAM_BXCR_SDBE) {
+ /* Bank is enabled */
+ membase = (unsigned long*)
+ (mfdcr(memcfgd) & SDRAM_BXCR_SDBA_MASK);
+
+ /*
+ * Run the short memory test
+ */
+ for (i = 0; i < NUMMEMTESTS; i++) {
+ for (j = 0; j < NUMMEMWORDS; j++) {
+ /* printf("bank enabled base:%x\n", &membase[j]); */
+ membase[j] = test[i][j];
+ ppcDcbf((unsigned long)&(membase[j]));
+ }
+
+ for (j = 0; j < NUMMEMWORDS; j++) {
+ if (membase[j] != test[i][j]) {
+ ppcDcbf((unsigned long)&(membase[j]));
+ return 0;
+ }
+ ppcDcbf((unsigned long)&(membase[j]));
+ }
+
+ if (j < NUMMEMWORDS)
+ return 0;
+ }
+
+ /*
+ * see if the rdclt value passed
+ */
+ if (i < NUMMEMTESTS)
+ return 0;
+ }
+ }
+
+ return 1;
+}
+
+static void program_tr1(void)
{
unsigned long tr0;
unsigned long tr1;
unsigned long ecc_temp;
unsigned long dlycal;
unsigned long dly_val;
- unsigned long i, j, k;
- unsigned long bxcr_num;
+ unsigned long k;
unsigned long max_pass_length;
unsigned long current_pass_length;
unsigned long current_fail_length;
unsigned char window_found;
unsigned char fail_found;
unsigned char pass_found;
- unsigned long * membase;
PPC440_SYS_INFO sys_info;
/*
window_found = FALSE;
fail_found = FALSE;
pass_found = FALSE;
-#ifdef DEBUG
- printf("Starting memory test ");
-#endif
+ debug("Starting memory test ");
+
for (k = 0; k < NUMHALFCYCLES; k++) {
- for (rdclt = 0; rdclt < dly_val; rdclt++) {
+ for (rdclt = 0; rdclt < dly_val; rdclt++) {
/*
* Set the timing reg for the test.
*/
mtsdram(mem_tr1, (tr1 | SDRAM_TR1_RDCT_ENCODE(rdclt)));
- for (bxcr_num = 0; bxcr_num < MAXBXCR; bxcr_num++) {
- mtdcr(memcfga, mem_b0cr + (bxcr_num<<2));
- if ((mfdcr(memcfgd) & SDRAM_BXCR_SDBE) == SDRAM_BXCR_SDBE) {
- /* Bank is enabled */
- membase = (unsigned long*)
- (mfdcr(memcfgd) & SDRAM_BXCR_SDBA_MASK);
-
- /*
- * Run the short memory test
- */
- for (i = 0; i < NUMMEMTESTS; i++) {
- for (j = 0; j < NUMMEMWORDS; j++) {
- membase[j] = test[i][j];
- ppcDcbf((unsigned long)&(membase[j]));
- }
-
- for (j = 0; j < NUMMEMWORDS; j++) {
- if (membase[j] != test[i][j]) {
- ppcDcbf((unsigned long)&(membase[j]));
- break;
- }
- ppcDcbf((unsigned long)&(membase[j]));
- }
-
- if (j < NUMMEMWORDS) {
- break;
- }
- }
-
- /*
- * see if the rdclt value passed
- */
- if (i < NUMMEMTESTS) {
- break;
- }
- }
- }
-
- if (bxcr_num == MAXBXCR) {
+ if (short_mem_test()) {
if (fail_found == TRUE) {
pass_found = TRUE;
if (current_pass_length == 0) {
}
}
}
-#ifdef DEBUG
- printf(".");
-#endif
+ debug(".");
+
if (window_found == TRUE) {
break;
}
tr1 = tr1 ^ SDRAM_TR1_RDCD_MASK;
rdclt_offset += dly_val;
}
-#ifdef DEBUG
- printf("\n");
-#endif
+ debug("\n");
/*
* make sure we find the window
*/
if (window_found == FALSE) {
printf("ERROR: Cannot determine a common read delay.\n");
- hang();
+ spd_ddr_init_hang ();
}
/*
}
tr1 |= SDRAM_TR1_RDCT_ENCODE(rdclt_average);
-#if 0
- printf("tr1: %x\n", tr1);
-#endif
+ debug("tr1: %x\n", tr1);
+
/*
* program SDRAM Timing Register 1 TR1
*/
mtsdram(mem_tr1, tr1);
}
-unsigned long program_bxcr(unsigned long* dimm_populated,
- unsigned char* iic0_dimm_addr,
- unsigned long num_dimm_banks)
+static unsigned long program_bxcr(unsigned long *dimm_populated,
+ unsigned char *iic0_dimm_addr,
+ unsigned long num_dimm_banks)
{
unsigned long dimm_num;
unsigned long bank_base_addr;
#ifdef CONFIG_BAMBOO
/*
* This next section is hardware dependent and must be programmed
- * to match the hardware. For bammboo, the following holds...
- * 1. SDRAM0_B0CR: Bank 0 of dimm 0 ctrl_bank_num : 0
+ * to match the hardware. For bamboo, the following holds...
+ * 1. SDRAM0_B0CR: Bank 0 of dimm 0 ctrl_bank_num : 0 (soldered onboard)
* 2. SDRAM0_B1CR: Bank 0 of dimm 1 ctrl_bank_num : 1
* 3. SDRAM0_B2CR: Bank 1 of dimm 1 ctrl_bank_num : 1
* 4. SDRAM0_B3CR: Bank 0 of dimm 2 ctrl_bank_num : 3
ctrl_bank_num[1] = 1;
ctrl_bank_num[2] = 3;
#else
+ /*
+ * Ocotea, Ebony and the other IBM/AMCC eval boards have
+ * 2 DIMM slots with each max 2 banks
+ */
ctrl_bank_num[0] = 0;
- ctrl_bank_num[1] = 1;
- ctrl_bank_num[2] = 2;
- ctrl_bank_num[3] = 3;
+ ctrl_bank_num[1] = 2;
#endif
/*
num_col_addr = spd_read(iic0_dimm_addr[dimm_num], 4);
num_banks = spd_read(iic0_dimm_addr[dimm_num], 5);
bank_size_id = spd_read(iic0_dimm_addr[dimm_num], 31);
+ debug("DIMM%d: row=%d col=%d banks=%d\n", dimm_num,
+ num_row_addr, num_col_addr, num_banks);
/*
* Set the SDRAM0_BxCR regs
printf("ERROR: Unsupported value for the banksize: %d.\n",
bank_size_id);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
switch (num_col_addr) {
printf("ERROR: Unsupported value for number of "
"column addresses: %d.\n", num_col_addr);
printf("Replace the DIMM module with a supported DIMM.\n\n");
- hang();
+ spd_ddr_init_hang ();
}
/*
*/
cr |= SDRAM_BXCR_SDBE;
- for (i = 0; i < num_banks; i++) {
- bank_parms[ctrl_bank_num[dimm_num]+i+dimm_num].bank_size_bytes =
- (4 * 1024 * 1024) * bank_size_id;
- bank_parms[ctrl_bank_num[dimm_num]+i+dimm_num].cr = cr;
- }
+ for (i = 0; i < num_banks; i++) {
+ bank_parms[ctrl_bank_num[dimm_num]+i].bank_size_bytes =
+ (4 << 20) * bank_size_id;
+ bank_parms[ctrl_bank_num[dimm_num]+i].cr = cr;
+ debug("DIMM%d-bank %d (SDRAM0_B%dCR): bank_size_bytes=%d\n",
+ dimm_num, i, ctrl_bank_num[dimm_num]+i,
+ bank_parms[ctrl_bank_num[dimm_num]+i].bank_size_bytes);
+ }
}
}
bank_parms[sorted_bank_num[bx_cr_num]].cr;
mtdcr(memcfgd, temp);
bank_base_addr += bank_parms[sorted_bank_num[bx_cr_num]].bank_size_bytes;
+ debug("SDRAM0_B%dCR=0x%08lx\n", sorted_bank_num[bx_cr_num], temp);
}
}
return(bank_base_addr);
}
-void program_ecc (unsigned long num_bytes)
+#ifdef CONFIG_DDR_ECC
+static void program_ecc(unsigned long num_bytes)
{
unsigned long bank_base_addr;
unsigned long current_address;
bank_base_addr = CFG_SDRAM_BASE;
if ((cfg0 & SDRAM_CFG0_MCHK_MASK) != SDRAM_CFG0_MCHK_NON) {
- mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) |
- SDRAM_CFG0_MCHK_GEN);
+ mtsdram(mem_cfg0, (cfg0 & ~SDRAM_CFG0_MCHK_MASK) | SDRAM_CFG0_MCHK_GEN);
- if ((cfg0 & SDRAM_CFG0_DMWD_MASK) == SDRAM_CFG0_DMWD_32) {
+ if ((cfg0 & SDRAM_CFG0_DMWD_MASK) == SDRAM_CFG0_DMWD_32)
address_increment = 4;
- } else {
+ else
address_increment = 8;
- }
current_address = (unsigned long)(bank_base_addr);
end_address = (unsigned long)(bank_base_addr) + num_bytes;
SDRAM_CFG0_MCHK_CHK);
}
}
+#endif /* CONFIG_DDR_ECC */
#endif /* CONFIG_SPD_EEPROM */
projects / platform / kernel / u-boot.git / blobdiff