config SUPPORT_TPL
bool
+config SPL_DFU_NO_RESET
+ bool
+
config SPL
bool
depends on SUPPORT_SPL
help
If you want to build SPL as well as the normal image, say Y.
+config SPL_RAW_IMAGE_SUPPORT
+ bool "Support SPL loading and booting of RAW images"
+ depends on SPL
+ default n if (ARCH_MX6 && (SPL_MMC_SUPPORT || SPL_SATA_SUPPORT))
+ default y if !TI_SECURE_DEVICE
+ help
+ SPL will support loading and booting a RAW image when this option
+ is y. If this is not set, SPL will move on to other available
+ boot media to find a suitable image.
+
+config SPL_LEGACY_IMAGE_SUPPORT
+ bool "Support SPL loading and booting of Legacy images"
+ default y if !TI_SECURE_DEVICE
+ help
+ SPL will support loading and booting Legacy images when this option
+ is y. If this is not set, SPL will move on to other available
+ boot media to find a suitable image.
+
config SPL_SYS_MALLOC_SIMPLE
bool
depends on SPL
banner ("U-Boot SPL ..."). This function should be provided by
the board.
+config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+ bool "MMC raw mode: by sector"
+ depends on SPL
+ default y if ARCH_SUNXI || ARCH_DAVINCI || ARCH_UNIPHIER ||ARCH_MX6 || \
+ ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \
+ ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || \
+ OMAP44XX || OMAP54XX || AM33XX || AM43XX
+ help
+ Use sector number for specifying U-Boot location on MMC/SD in
+ raw mode.
+
+config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
+ hex "Address on the MMC to load U-Boot from"
+ depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+ default 0x50 if ARCH_SUNXI
+ default 0x75 if ARCH_DAVINCI
+ default 0x8a if ARCH_MX6
+ default 0x100 if ARCH_ROCKCHIP || ARCH_UNIPHIER
+ default 0x140 if ARCH_MVEBU
+ default 0x200 if ARCH_SOCFPGA || ARCH_AT91
+ default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \
+ OMAP54XX || AM33XX || AM43XX
+ help
+ Address on the MMC to load U-Boot from, when the MMC is being used
+ in raw mode. Units: MMC sectors (1 sector = 512 bytes).
+
+config SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ bool "MMC Raw mode: by partition"
+ depends on SPL
+ help
+ Use a partition for loading U-Boot when using MMC/SD in raw mode.
+
+config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
+ hex "Partition to use to load U-Boot from"
+ depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ default 1
+ help
+ Partition on the MMC to load U-Boot from when the MMC is being
+ used in raw mode
+
+config SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
+ bool "MMC raw mode: by partition type"
+ depends on SPL && DOS_PARTITION && \
+ SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ help
+ Use partition type for specifying U-Boot partition on MMC/SD in
+ raw mode. U-Boot will be loaded from the first partition of this
+ type to be found.
+
+config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
+ hex "Partition Type on the MMC to load U-Boot from"
+ depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
+ help
+ Partition Type on the MMC to load U-Boot from, when the MMC is being
+ used in raw mode.
+
config TPL
bool
depends on SPL && SUPPORT_TPL
SHA256 variant is supported: SHA512 and others are not currently
supported in U-Boot.
+config SPL_CPU_SUPPORT
+ bool "Support CPU drivers"
+ depends on SPL
+ help
+ Enable this to support CPU drivers in SPL. These drivers can set
+ up CPUs and provide information about them such as the model and
+ name. This can be useful in SPL since setting up the CPUs earlier
+ may improve boot performance. Enable this option to build the
+ drivers in drivers/cpu as part of an SPL build.
+
config SPL_CRYPTO_SUPPORT
bool "Support crypto drivers"
depends on SPL
config SPL_MMC_SUPPORT
bool "Support MMC"
- depends on SPL
+ depends on SPL && GENERIC_MMC
help
Enable support for MMC (Multimedia Card) within SPL. This enables
the MMC protocol implementation and allows any enabled drivers to
Enable booting directly to an OS from SPL.
for more info read doc/README.falcon
+if SPL_OS_BOOT
+config SYS_OS_BASE
+ hex "addr, where OS is found"
+ depends on SPL && SPL_NOR_SUPPORT
+ help
+ Specify the address, where the OS image is found, which
+ gets booted.
+
+endif # SPL_OS_BOOT
+
+config SPL_PCI_SUPPORT
+ bool "Support PCI drivers"
+ depends on SPL
+ help
+ Enable support for PCI in SPL. For platforms that need PCI to boot,
+ or must perform some init using PCI in SPL, this provides the
+ necessary driver support. This enables the drivers in drivers/pci
+ as part of an SPL build.
+
+config SPL_PCH_SUPPORT
+ bool "Support PCH drivers"
+ depends on SPL
+ help
+ Enable support for PCH (Platform Controller Hub) devices in SPL.
+ These are used to set up GPIOs and the SPI peripheral early in
+ boot. This enables the drivers in drivers/pch as part of an SPL
+ build.
+
config SPL_POST_MEM_SUPPORT
bool "Support POST drivers"
depends on SPL
in drivers/power, drivers/power/pmic and drivers/power/regulator
as part of an SPL build.
+config SPL_RAM_SUPPORT
+ bool "Support booting from RAM"
+ depends on SPL
+ default y if MICROBLAZE || ARCH_SOCFPGA || TEGRA || ARCH_ZYNQ
+ help
+ Enable booting of an image in RAM. The image can be preloaded or
+ it can be loaded by SPL directly into RAM (e.g. using USB).
+
+config SPL_RAM_DEVICE
+ bool "Support booting from preloaded image in RAM"
+ depends on SPL_RAM_SUPPORT
+ default y if MICROBLAZE || ARCH_SOCFPGA || TEGRA || ARCH_ZYNQ
+ help
+ Enable booting of an image already loaded in RAM. The image has to
+ be already in memory when SPL takes over, e.g. loaded by the boot
+ ROM.
+
+config SPL_RTC_SUPPORT
+ bool "Support RTC drivers"
+ depends on SPL
+ help
+ Enable RTC (Real-time Clock) support in SPL. This includes support
+ for reading and setting the time. Some RTC devices also have some
+ non-volatile (battery-backed) memory which is accessible if
+ needed. This enables the drivers in drivers/rtc as part of an SPL
+ build.
+
config SPL_SATA_SUPPORT
bool "Support loading from SATA"
depends on SPL
enable SPI drivers that are needed for other purposes also, such
as a SPI PMIC.
-config SPL_USBETH_SUPPORT
- bool "Support USB Ethernet drivers"
+config SPL_TIMER_SUPPORT
+ bool "Support timer drivers"
depends on SPL
help
- Enable access to the USB network subsystem and associated
- drivers in SPL. This permits SPL to load U-Boot over a
- USB-connected Ethernet link (such as a USB Ethernet dongle) rather
- than from an onboard peripheral. Environment support is required
- since the network stack uses a number of environment variables.
- See also SPL_NET_SUPPORT and SPL_ETH_SUPPORT.
+ Enable support for timer drivers in SPL. These can be used to get
+ a timer value when in SPL, or perhaps for implementing a delay
+ function. This enables the drivers in drivers/timer as part of an
+ SPL build.
config SPL_USB_HOST_SUPPORT
bool "Support USB host drivers"
config options. This enables loading from USB using a configured
device.
+config SPL_USB_GADGET_SUPPORT
+ bool "Suppport USB Gadget drivers"
+ depends on SPL
+ help
+ Enable USB Gadget API which allows to enable USB device functions
+ in SPL.
+
+if SPL_USB_GADGET_SUPPORT
+
+config SPL_USBETH_SUPPORT
+ bool "Support USB Ethernet drivers"
+ help
+ Enable access to the USB network subsystem and associated
+ drivers in SPL. This permits SPL to load U-Boot over a
+ USB-connected Ethernet link (such as a USB Ethernet dongle) rather
+ than from an onboard peripheral. Environment support is required
+ since the network stack uses a number of environment variables.
+ See also SPL_NET_SUPPORT and SPL_ETH_SUPPORT.
+
+config SPL_DFU_SUPPORT
+ bool "Support DFU (Device Firmware Upgarde)"
+ select SPL_HASH_SUPPORT
+ select SPL_DFU_NO_RESET
+ depends on SPL_RAM_SUPPORT
+ help
+ This feature enables the DFU (Device Firmware Upgarde) in SPL with
+ RAM memory device support. The ROM code will load and execute
+ the SPL built with dfu. The user can load binaries (u-boot/kernel) to
+ selected device partition from host-pc using dfu-utils.
+ This feature is useful to flash the binaries to factory or bare-metal
+ boards using USB interface.
+
+choice
+ bool "DFU device selection"
+ depends on SPL_DFU_SUPPORT
+
+config SPL_DFU_RAM
+ bool "RAM device"
+ depends on SPL_DFU_SUPPORT && SPL_RAM_SUPPORT
+ help
+ select RAM/DDR memory device for loading binary images
+ (u-boot/kernel) to the selected device partition using
+ DFU and execute the u-boot/kernel from RAM.
+
+endchoice
+
+endif
+
config SPL_WATCHDOG_SUPPORT
bool "Support watchdog drivers"
depends on SPL