-menu "SPL / TPL"
+menu "SPL / TPL / VPL"
config SUPPORT_SPL
bool
config SUPPORT_TPL
bool
+config SUPPORT_VPL
+ bool
+
config SPL_DFU_NO_RESET
bool
of SRAM available for SPL when the stack required before reolcation
uses this SRAM, too.
+config SPL_MAX_SIZE
+ hex "Maximum size of the SPL image, excluding BSS"
+ default 0x30000 if ARCH_MX6 && MX6_OCRAM_256KB
+ default 0x1b000 if AM33XX && !TI_SECURE_DEVICE
+ default 0x10000 if ARCH_MX6 && !MX6_OCRAM_256KB
+ default 0x7fa0 if SUNXI_SRAM_ADDRESS = 0x10000
+ default 0x7fa0 if SUNXI_SRAM_ADDRESS = 0x20000 && !MACH_SUN50I_H616
+ default 0x7000 if RCAR_GEN3
+ default 0x5fa0 if SUNXI_SRAM_ADDRESS = 0x0
+ default 0x0
+ help
+ Maximum size of the SPL image (text, data, rodata, and linker lists
+ sections), BSS excluded. When defined, the linker checks that the
+ actual size does not exceed it.
+
+config SPL_PAD_TO
+ hex "Offset to which the SPL should be padded before appending the SPL payload"
+ default 0x31000 if ARCH_MX6 && MX6_OCRAM_256KB
+ default 0x11000 if ARCH_MX7 || (ARCH_MX6 && !MX6_OCRAM_256KB)
+ default 0x10000 if ARCH_KEYSTONE
+ default 0x8000 if ARCH_SUNXI && !MACH_SUN50I_H616
+ default TPL_MAX_SIZE if TPL_MAX_SIZE > SPL_MAX_SIZE
+ default SPL_MAX_SIZE
+ help
+ Image offset to which the SPL should be padded before appending the
+ SPL payload. By default, this is defined as CONFIG_SPL_MAX_SIZE, or 0 if
+ CONFIG_SPL_MAX_SIZE is undefined. CONFIG_SPL_PAD_TO must be either
+ 0, meaning to append the SPL payload without any padding, or >=
+ CONFIG_SPL_MAX_SIZE.
+
+config SPL_HAS_BSS_LINKER_SECTION
+ depends on SPL_FRAMEWORK
+ bool "Use a specific address for the BSS via the linker script"
+ default y if ARCH_SUNXI || ARCH_MX6 || ARCH_OMAP2PLUS || MIPS || RISCV
+
+config SPL_BSS_START_ADDR
+ hex "Link address for the BSS within the SPL binary"
+ depends on SPL_HAS_BSS_LINKER_SECTION
+ default 0x88200000 if (ARCH_MX6 && (MX6SX || MX6SL || MX6UL || MX6ULL)) || ARCH_MX7
+ default 0x18200000 if ARCH_MX6 && !(MX6SX || MX6SL || MX6UL || MX6ULL)
+ default 0x80a00000 if ARCH_OMAP2PLUS
+ default 0x81f80000 if ARCH_SUNXI && MACH_SUNIV
+ default 0x4ff80000 if ARCH_SUNXI && !(MACH_SUN9I || MACH_SUNIV)
+ default 0x2ff80000 if ARCH_SUNXI && MACH_SUN9I
+
+choice
+ prompt "Enforce SPL BSS limit"
+ depends on SPL && !PPC
+ default SPL_BSS_LIMIT
+ help
+ In some platforms we only want to enforce a limit on the size of the
+ BSS in memory. On other platforms we need to enforce a limit on the
+ whole of the memory allocation as we're strictly limited to a small
+ typically non-DRAM location. Finally, other platforms do not enforce
+ a memory limit within SPL.
+
+config SPL_NO_BSS_LIMIT
+ bool "Do not enforce a build time limit on the size of the BSS"
+
+config SPL_BSS_LIMIT
+ bool "Enforce a limit on the size of the BSS only"
+
+config SPL_FOOTPRINT_LIMIT
+ bool "Enforce a limit on the whole of memory allocated to SPL, BSS included"
+
+endchoice
+
+config SPL_BSS_MAX_SIZE
+ hex "Maximum size in memory allocated to the SPL BSS"
+ depends on SPL_BSS_LIMIT
+ default 0x100000 if ARCH_MX6 || RISCV
+ default 0x80000 if ARCH_OMAP2PLUS || ARCH_SUNXI
+ help
+ When non-zero, the linker checks that the actual memory used by SPL
+ from __bss_start to __bss_end does not exceed it.
+
+config SPL_MAX_FOOTPRINT
+ hex "Maximum size in memory allocated to the SPL, BSS included"
+ depends on SPL_FOOTPRINT_LIMIT
+ help
+ When non-zero, the linker checks that the actual memory used by SPL
+ from _start to __bss_end does not exceed it.
+
config SPL_SYS_STACK_F_CHECK_BYTE
hex
default 0xaa
This adds a small amount to SPL code size, perhaps 100 bytes.
+config SPL_BINMAN_SYMBOLS
+ bool "Declare binman symbols in SPL"
+ depends on SPL_FRAMEWORK && BINMAN
+ default y
+ help
+ This enables use of symbols in SPL which refer to U-Boot, enabling SPL
+ to obtain the location of U-Boot simply by calling spl_get_image_pos()
+ and spl_get_image_size().
+
+ For this to work, you must have a U-Boot image in the binman image, so
+ binman can update SPL with the location of it.
+
menu "PowerPC and LayerScape SPL Boot options"
config SPL_NAND_BOOT
Create boot binary having SPL binary in PBI format concatenated with
u-boot binary.
+config SPL_SYS_CCSR_DO_NOT_RELOCATE
+ bool "Ensures that CCSR is not relocated"
+ depends on PPC
+ help
+ If this is defined, then CONFIG_SYS_CCSRBAR_PHYS will be forced to a
+ value that ensures that CCSR is not relocated.
+
+config TPL_SYS_CCSR_DO_NOT_RELOCATE
+ def_bool y
+ depends on SPL_SYS_CCSR_DO_NOT_RELOCATE
+
+endmenu
+
+menu "PowerPC SPL / TPL specific options"
+ depends on PPC && (SPL && !SPL_FRAMEWORK)
+
+config SPL_INIT_MINIMAL
+ bool "Arch init code will be built for a very small image"
+
+config SPL_FLUSH_IMAGE
+ bool "Clean dcache and invalidate icache after loading the image"
+
+config SPL_SKIP_RELOCATE
+ bool "Skip relocating SPL"
+
+config SPL_RELOC_TEXT_BASE
+ hex "Address to relocate SPL to"
+ default SPL_TEXT_BASE
+ help
+ If unspecified, this is equal to CONFIG_SPL_TEXT_BASE (i.e. no
+ relocation is done).
+
+config SPL_RELOC_STACK
+ hex "Address of the start of the stack SPL will use after relocation."
+ help
+ If unspecified, this is equal to CONFIG_SYS_SPL_MALLOC_START. Starting
+ address of the malloc pool used in SPL. When this option is set the full
+ malloc is used in SPL and it is set up by spl_init() and before that, the
+ simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
+
+config SPL_RELOC_MALLOC
+ bool "SPL has malloc pool after relocation"
+
+config SPL_RELOC_MALLOC_ADDR
+ hex "Address of malloc pool in SPL"
+ depends on SPL_RELOC_MALLOC
+
+config SPL_RELOC_MALLOC_SIZE
+ hex "Size of malloc pool in SPL"
+ depends on SPL_RELOC_MALLOC
+
+config TPL_RELOC_TEXT_BASE
+ hex "Address to relocate TPL to"
+ depends on TPL
+ default TPL_TEXT_BASE
+ help
+ If unspecified, this is equal to CONFIG_TPL_TEXT_BASE (i.e. no
+ relocation is done).
+
+config TPL_RELOC_STACK
+ hex "Address of the start of the stack TPL will use after relocation."
+ depends on TPL
+ help
+ If unspecified, this is equal to CONFIG_SYS_TPL_MALLOC_START. Starting
+ address of the malloc pool used in TPL. When this option is set the full
+ malloc is used in TPL and it is set up by spl_init() and before that, the
+ simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.
+
+config TPL_RELOC_MALLOC
+ bool "TPL has malloc pool after relocation"
+ depends on TPL
+
+config TPL_RELOC_MALLOC_ADDR
+ hex "Address of malloc pool in TPL"
+ depends on TPL_RELOC_MALLOC
+
+config TPL_RELOC_MALLOC_SIZE
+ hex "Size of malloc pool in TPL"
+ depends on TPL_RELOC_MALLOC
+
endmenu
config HANDOFF
spl_board_init() from board_init_r(). This function should be
provided by the board.
+config VPL_BOARD_INIT
+ bool "Call board-specific initialization in VPL"
+ help
+ If this option is enabled, U-Boot will call the function
+ spl_board_init() from board_init_r(). This function should be
+ provided by the board.
+
config SPL_BOOTROM_SUPPORT
bool "Support returning to the BOOTROM"
help
config SPL_RAW_IMAGE_SUPPORT
bool "Support SPL loading and booting of RAW images"
- default n if (ARCH_MX6 && (SPL_MMC || SPL_SATA_SUPPORT))
- default y if !TI_SECURE_DEVICE
+ default n if (ARCH_MX6 && (SPL_MMC || SPL_SATA))
+ default y
+ depends on !TI_SECURE_DEVICE
help
SPL will support loading and booting a RAW image when this option
is y. If this is not set, SPL will move on to other available
boot media to find a suitable image.
-config SPL_LEGACY_IMAGE_SUPPORT
+config SPL_LEGACY_IMAGE_FORMAT
bool "Support SPL loading and booting of Legacy images"
- default y if !TI_SECURE_DEVICE && !SPL_LOAD_FIT
+ default y if !SPL_LOAD_FIT
+ depends on !TI_SECURE_DEVICE
help
SPL will support loading and booting Legacy images when this option
is y. If this is not set, SPL will move on to other available
config SPL_LEGACY_IMAGE_CRC_CHECK
bool "Check CRC of Legacy images"
- depends on SPL_LEGACY_IMAGE_SUPPORT
+ depends on SPL_LEGACY_IMAGE_FORMAT
select SPL_CRC32
help
Enable this to check the CRC of Legacy images. While this increases
this will make the TPL binary smaller at the cost of more heap
usage as the *_simple malloc functions do not re-use free-ed mem.
+config SPL_SHARES_INIT_SP_ADDR
+ bool "SPL and U-Boot use the same initial stack pointer location"
+ depends on (ARM || ARCH_JZ47XX || MICROBLAZE || RISCV) && SPL_FRAMEWORK
+ default n if ARCH_SUNXI || ARCH_MX6 || ARCH_MX7
+ default y
+ help
+ In many cases, we can use the same initial stack pointer address for
+ both SPL and U-Boot itself. If you need to specify a different address
+ however, say N here and then set a different value in CONFIG_SPL_STACK.
+
+config SPL_STACK
+ hex "Initial stack pointer location"
+ depends on (ARM || ARCH_JZ47XX || MICROBLAZE || RISCV) && SPL_FRAMEWORK
+ depends on !SPL_SHARES_INIT_SP_ADDR
+ default 0x946bb8 if ARCH_MX7
+ default 0x93ffb8 if ARCH_MX6 && MX6_OCRAM_256KB
+ default 0x91ffb8 if ARCH_MX6 && !MX6_OCRAM_256KB
+ help
+ Address of the start of the stack SPL will use before SDRAM is
+ initialized.
+
config SPL_STACK_R
bool "Enable SDRAM location for SPL stack"
help
location is used. Normally we put the device tree at the end of BSS
but with this option enabled, it goes at _image_binary_end.
+config SYS_SPL_MALLOC
+ bool "Enable malloc pool in SPL"
+ depends on SPL_FRAMEWORK
+
+config HAS_CUSTOM_SPL_MALLOC_START
+ bool "For the SPL malloc pool, define a custom starting address"
+ depends on SYS_SPL_MALLOC
+
+config CUSTOM_SYS_SPL_MALLOC_ADDR
+ hex "SPL malloc addr"
+ depends on HAS_CUSTOM_SPL_MALLOC_START
+
+config SYS_SPL_MALLOC_SIZE
+ hex "Size of the SPL malloc pool"
+ depends on SYS_SPL_MALLOC
+ default 0x100000
+
config SPL_READ_ONLY
bool
depends on SPL_OF_PLATDATA
writeable memory) of anything it wants to modify, such as
device-private data.
+config TPL_SEPARATE_BSS
+ bool "BSS section is in a different memory region from text"
+ default y if SPL_SEPARATE_BSS
+ help
+ Some platforms need a large BSS region in TPL and can provide this
+ because RAM is already set up. In this case BSS can be moved to RAM.
+ This option should then be enabled so that the correct device tree
+ location is used. Normally we put the device tree at the end of BSS
+ but with this option enabled, it goes at _image_binary_end.
+
config SPL_BANNER_PRINT
bool "Enable output of the SPL banner 'U-Boot SPL ...'"
default y
config SPL_CRC32
bool "Support CRC32"
- default y if SPL_LEGACY_IMAGE_SUPPORT
+ default y if SPL_LEGACY_IMAGE_FORMAT || SPL_EFI_PARTITION
+ default y if SPL_ENV_SUPPORT || TPL_BLOBLIST
help
Enable this to support CRC32 in uImages or FIT images within SPL.
This is a 32-bit checksum value that can be used to verify images.
applications where images may be changed maliciously, you should
consider SHA256 or SHA384.
-config SPL_FIT_SHA1
- bool "Support SHA1"
- depends on SPL_FIT
- select SHA1
- help
- Enable this to support SHA1 in FIT images within SPL. A SHA1
- checksum is a 160-bit (20-byte) hash value used to check that the
- image contents have not been corrupted or maliciously altered.
- While SHA1 is fairly secure it is coming to the end of its life
- due to the expanding computing power available to brute-force
- attacks. For more security, consider SHA256 or SHA384.
-
-config SPL_FIT_SHA256
- bool "Support SHA256"
- depends on SPL_FIT
- select SHA256
- help
- Enable this to support SHA256 in FIT images within SPL. A SHA256
- checksum is a 256-bit (32-byte) hash value used to check that the
- image contents have not been corrupted.
-
-config SPL_FIT_SHA384
- bool "Support SHA384"
- depends on SPL_FIT
- select SHA384
- select SHA512_ALGO
- help
- Enable this to support SHA384 in FIT images within SPL. A SHA384
- checksum is a 384-bit (48-byte) hash value used to check that the
- image contents have not been corrupted. Use this for the highest
- security.
-
-config SPL_FIT_SHA512
- bool "Support SHA512"
- depends on SPL_FIT
- select SHA512
- select SHA512_ALGO
- help
- Enable this to support SHA512 in FIT images within SPL. A SHA512
- checksum is a 512-bit (64-byte) hash value used to check that the
- image contents have not been corrupted.
-
config SPL_FIT_IMAGE_TINY
bool "Remove functionality from SPL FIT loading to reduce size"
depends on SPL_FIT
ensure this information is available to the next image
invoked).
-config SPL_CACHE_SUPPORT
+config SPL_CACHE
bool "Support CACHE drivers"
help
Enable CACHE drivers in SPL. These drivers can keep data so that
this option to build the drivers in drivers/crypto as part of an
SPL build.
-config SPL_HASH_SUPPORT
- bool "Support hashing drivers"
- select SHA1
- select SHA256
- help
- Enable hashing drivers in SPL. These drivers can be used to
- accelerate secure boot processing in secure applications. Enable
- this option to build system-specific drivers for hash acceleration
- as part of an SPL build.
-
-config TPL_HASH_SUPPORT
- bool "Support hashing drivers in TPL"
- depends on TPL
- select SHA1
- select SHA256
- help
- Enable hashing drivers in SPL. These drivers can be used to
- accelerate secure boot processing in secure applications. Enable
- this option to build system-specific drivers for hash acceleration
- as part of an SPL build.
-
config SPL_DMA
bool "Support DMA drivers"
help
config SPL_ETH
bool "Support Ethernet"
depends on SPL_ENV_SUPPORT
+ depends on SPL_NET
help
Enable access to the network subsystem and associated Ethernet
drivers in SPL. This permits SPL to load U-Boot over an Ethernet
link rather than from an on-board peripheral. Environment support
is required since the network stack uses a number of environment
- variables. See also SPL_NET_SUPPORT.
+ variables. See also SPL_NET.
config SPL_FS_EXT4
bool "Support EXT filesystems"
filesystem from within SPL. Support for the underlying block
device (e.g. MMC or USB) must be enabled separately.
+config SPL_FS_LOAD_PAYLOAD_NAME
+ string "File to load for U-Boot from the filesystem"
+ depends on SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS
+ default "tispl.bin" if SYS_K3_SPL_ATF
+ default "u-boot.itb" if SPL_LOAD_FIT
+ default "u-boot.img"
+ help
+ Filename to read to load U-Boot when reading from filesystem.
+
+config SPL_FS_LOAD_KERNEL_NAME
+ string "File to load for the OS kernel from the filesystem"
+ depends on (SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS) && SPL_OS_BOOT
+ default "uImage"
+ help
+ Filename to read to load for the OS kernel when reading from the
+ filesystem.
+
+config SPL_FS_LOAD_ARGS_NAME
+ string "File to load for the OS kernel argument parameters from the filesystem"
+ depends on (SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS) && SPL_OS_BOOT
+ default "args"
+ help
+ Filename to read to load for the OS kernel argument parameters from
+ the filesystem.
+
config SPL_FAT_WRITE
bool "Support write for FAT filesystems"
help
default 1
help
Partition on the MMC to load U-Boot from when the MMC is being
- used in fs mode
+ used in fs mode.
+ Use -1 as a special value to use the first bootable partition.
config SPL_MMC_TINY
bool "Tiny MMC framework in SPL"
Enable write access to MMC and SD Cards in SPL
-config SPL_MPC8XXX_INIT_DDR_SUPPORT
+config SPL_MPC8XXX_INIT_DDR
bool "Support MPC8XXX DDR init"
help
Enable support for DDR-SDRAM (double-data-rate synchronous dynamic
This enables the drivers in drivers/mtd/nand/raw as part of an SPL
build.
+config SPL_NAND_RAW_ONLY
+ bool "Support to boot only raw u-boot.bin images"
+ depends on SPL_NAND_SUPPORT
+ help
+ Use this only if you need to save space.
+
config SPL_NAND_DRIVERS
bool "Use standard NAND driver"
help
SPL uses normal NAND drivers, not minimal drivers.
config SPL_NAND_ECC
- bool "Include standard software ECC in the SPL"
+ bool "Include standard ECC in SPL"
+
+config SPL_NAND_SOFTECC
+ bool "Use software ECC in SPL"
+ depends on SPL_NAND_ECC
config SPL_NAND_SIMPLE
bool "Support simple NAND drivers in SPL"
README.ubispl for more info.
if SPL_DM
-config SPL_CACHE
- depends on CACHE
- bool "Support cache drivers in SPL"
- help
- Enable support for cache drivers in SPL.
-
config SPL_DM_SPI
bool "Support SPI DM drivers in SPL"
help
endif # if SPL_UBI
-config SPL_NET_SUPPORT
+config SPL_NET
bool "Support networking"
help
Enable support for network devices (such as Ethernet) in SPL.
the network stack uses a number of environment variables. See also
SPL_ETH.
-if SPL_NET_SUPPORT
+if SPL_NET
config SPL_NET_VCI_STRING
string "BOOTP Vendor Class Identifier string sent by SPL"
help
of a client. This is often used in practice to allow for the DHCP
server to specify different files to load depending on if the ROM,
SPL or U-Boot itself makes the request
-endif # if SPL_NET_SUPPORT
+endif # if SPL_NET
config SPL_NO_CPU_SUPPORT
bool "Drop CPU code in SPL"
endif # SPL_OS_BOOT
+config SPL_FALCON_BOOT_MMCSD
+ bool "Enable Falcon boot from MMC or SD media"
+ depends on SPL_OS_BOOT && SPL_MMC
+ help
+ Select this if the Falcon mode OS image mode is on MMC or SD media.
+
+config SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
+ hex "Falcon mode: Sector to load kernel uImage from MMC"
+ depends on SPL_FALCON_BOOT_MMCSD
+ help
+ When Falcon mode is used with an MMC or SD media, SPL needs to know
+ where to look for the kernel uImage. The image is expected to begin
+ at the raw MMC specified in this config.
+ Note that the Falcon mode image can also be a FIT, if FIT support is
+ enabled.
+
config SPL_PAYLOAD
string "SPL payload"
default "tpl/u-boot-with-tpl.bin" if TPL
config SPL_POWER_DOMAIN
bool "Support power domain drivers"
+ select SPL_POWER
help
Enable support for power domain control in SPL. Many SoCs allow
power to be applied to or removed from portions of the SoC (power
needed. This enables the drivers in drivers/rtc as part of an SPL
build.
-config SPL_SATA_SUPPORT
+config SPL_SATA
bool "Support loading from SATA"
help
Enable support for SATA (Serial AT attachment) in SPL. This allows
config SPL_SATA_RAW_U_BOOT_USE_SECTOR
bool "SATA raw mode: by sector"
- depends on SPL_SATA_SUPPORT
+ depends on SPL_SATA
default y if ARCH_MVEBU
help
Use sector number for specifying U-Boot location on SATA disk in
config SPL_USB_ETHER
bool "Support USB Ethernet drivers"
+ depends on SPL_NET
help
Enable access to the USB network subsystem and associated
drivers in SPL. This permits SPL to load U-Boot over a
USB-connected Ethernet link (such as a USB Ethernet dongle) rather
than from an onboard peripheral. Environment support is required
since the network stack uses a number of environment variables.
- See also SPL_NET_SUPPORT and SPL_ETH.
+ See also SPL_NET and SPL_ETH.
config SPL_DFU
bool "Support DFU (Device Firmware Upgrade)"
- select SPL_HASH_SUPPORT
+ select SPL_HASH
select SPL_DFU_NO_RESET
depends on SPL_RAM_SUPPORT
help
Enable access to the AM33xx RTC and select the external 32kHz clock
source.
-config SPL_OPTEE
- bool "Support OP-TEE Trusted OS"
+config SPL_OPTEE_IMAGE
+ bool "Support OP-TEE Trusted OS image in SPL"
depends on ARM
help
- OP-TEE is an open source Trusted OS which is loaded by SPL.
+ OP-TEE is an open source Trusted OS which is loaded by SPL.
More detail at: https://github.com/OP-TEE/optee_os
config SPL_OPENSBI
Specifies the maximum length of the U-Boot TPL image.
If this value is zero, it is ignored.
+config TPL_BINMAN_SYMBOLS
+ bool "Declare binman symbols in TPL"
+ depends on SPL_FRAMEWORK && BINMAN
+ default y
+ help
+ This enables use of symbols in TPL which refer to U-Boot, enabling TPL
+ to obtain the location of U-Boot simply by calling spl_get_image_pos()
+ and spl_get_image_size().
+
+ For this to work, you must have a U-Boot image in the binman image, so
+ binman can update TPL with the location of it.
+
config TPL_FRAMEWORK
bool "Support TPL based upon the common SPL framework"
default y if SPL_FRAMEWORK
May be left empty to trigger the Makefile infrastructure to
fall back to the linker-script used for the SPL stage.
-config TPL_NEEDS_SEPARATE_TEXT_BASE
- bool "TPL needs a separate text-base"
- depends on TPL
- help
- Enable, if the TPL stage should not inherit its text-base
- from the SPL stage. When enabled, a base address for the
- .text sections of the TPL stage has to be set below.
-
config TPL_NEEDS_SEPARATE_STACK
bool "TPL needs a separate initial stack-pointer"
depends on TPL
Enable, if the TPL stage should not inherit its initial
stack-pointer from the settings for the SPL stage.
+config TPL_POWER
+ bool "Support power drivers"
+ help
+ Enable support for power control in TPL. This includes support
+ for PMICs (Power-management Integrated Circuits) and some of the
+ features provided by PMICs. In particular, voltage regulators can
+ be used to enable/disable power and vary its voltage. That can be
+ useful in TPL to turn on boot peripherals and adjust CPU voltage
+ so that the clock speed can be increased. This enables the drivers
+ in drivers/power, drivers/power/pmic and drivers/power/regulator
+ as part of an TPL build.
+
config TPL_TEXT_BASE
hex "Base address for the .text section of the TPL stage"
- depends on TPL_NEEDS_SEPARATE_TEXT_BASE
+ default 0
help
The base address for the .text section of the TPL stage.
config TPL_MAX_SIZE
- int "Maximum size (in bytes) for the TPL stage"
- default 0
- depends on TPL
+ hex "Maximum size (in bytes) for the TPL stage"
+ default 0x2e000 if ROCKCHIP_RK3399
+ default 0x8000 if ROCKCHIP_RK3288
+ default 0x7000 if ROCKCHIP_RK322X || ROCKCHIP_RK3328 || ROCKCHIP_RK3368
+ default 0x2800 if ROCKCHIP_PX30
+ default 0x0
help
The maximum size (in bytes) of the TPL stage.
+config TPL_PAD_TO
+ hex "Offset to which the TPL should be padded before appending the TPL payload"
+ depends on !TPL_FRAMEWORK && PPC
+ default TPL_MAX_SIZE
+ help
+ Image offset to which the TPL should be padded before appending the
+ TPL payload. By default, this is defined as CONFIG_TPL_MAX_SIZE, or 0 if
+ CONFIG_TPL_MAX_SIZE is undefined. CONFIG_TPL_PAD_TO must be either
+ 0, meaning to append the TPL payload without any padding, or >=
+ CONFIG_TPL_MAX_SIZE.
+
config TPL_STACK
hex "Address of the initial stack-pointer for the TPL stage"
depends on TPL_NEEDS_SEPARATE_STACK
BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
boot device list, if not implemented for a given board)
+config TPL_CRC32
+ bool "Support CRC32 in TPL"
+ default y if TPL_ENV_SUPPORT || TPL_BLOBLIST
+ help
+ Enable this to support CRC32 in uImages or FIT images within SPL.
+ This is a 32-bit checksum value that can be used to verify images.
+ For FIT images, this is the least secure type of checksum, suitable
+ for detected accidental image corruption. For secure applications you
+ should consider SHA1 or SHA256.
+
config TPL_DRIVERS_MISC
bool "Support misc drivers in TPL"
help
Enable support for generic U-Boot libraries within TPL. See
SPL_LIBGENERIC_SUPPORT for details.
-config TPL_MPC8XXX_INIT_DDR_SUPPORT
+config TPL_MPC8XXX_INIT_DDR
bool "Support MPC8XXX DDR init"
help
Enable support for DDR-SDRAM on the MPC8XXX family within TPL. See
- SPL_MPC8XXX_INIT_DDR_SUPPORT for details.
+ SPL_MPC8XXX_INIT_DDR for details.
config TPL_MMC
bool "Support MMC"
endif # TPL
+config VPL
+ bool
+ depends on SUPPORT_SPL
+ prompt "Enable VPL"
+ help
+ If you want to build VPL as well as the normal image, TPL and SPL,
+ say Y.
+
+if VPL
+
+config VPL_BANNER_PRINT
+ bool "Enable output of the VPL banner 'U-Boot VPL ...'"
+ depends on VPL
+ default y
+ help
+ If this option is enabled, VPL will print the banner with version
+ info. Disabling this option could be useful to reduce VPL boot time
+ (e.g. approx. 6 ms faster, when output on i.MX6 with 115200 baud).
+
+config VPL_BOARD_INIT
+ bool "Call board-specific initialization in VPL"
+ help
+ If this option is enabled, U-Boot will call the function
+ spl_board_init() from board_init_r(). This function should be
+ provided by the board.
+
+config VPL_CACHE
+ depends on CACHE
+ bool "Support cache drivers in VPL"
+ help
+ Enable support for cache drivers in VPL.
+
+config VPL_CRC32
+ bool "Support CRC32 in VPL"
+ default y if VPL_ENV_SUPPORT || VPL_BLOBLIST
+ help
+ Enable this to support CRC32 in uImages or FIT images within VPL.
+ This is a 32-bit checksum value that can be used to verify images.
+ For FIT images, this is the least secure type of checksum, suitable
+ for detected accidental image corruption. For secure applications you
+ should consider SHA1 or SHA256.
+
+config VPL_DM_SPI
+ bool "Support SPI DM drivers in VPL"
+ help
+ Enable support for SPI DM drivers in VPL.
+
+config VPL_DM_SPI_FLASH
+ bool "Support SPI DM FLASH drivers in VPL"
+ help
+ Enable support for SPI DM flash drivers in VPL.
+
+config VPL_FRAMEWORK
+ bool "Support VPL based upon the common SPL framework"
+ default y
+ help
+ Enable the SPL framework under common/spl/ for VPL builds.
+ This framework supports MMC, NAND and YMODEM and other methods
+ loading of U-Boot's next stage. If unsure, say Y.
+
+config VPL_HANDOFF
+ bool "Pass hand-off information from VPL to SPL"
+ depends on HANDOFF && VPL_BLOBLIST
+ default y
+ help
+ This option enables VPL to write handoff information. This can be
+ used to pass information like the size of SDRAM from VPL to SPL. Also
+ VPL can receive information from TPL in the same place if that is
+ enabled.
+
+config VPL_LIBCOMMON_SUPPORT
+ bool "Support common libraries"
+ default y if SPL_LIBCOMMON_SUPPORT
+ help
+ Enable support for common U-Boot libraries within VPL. See
+ SPL_LIBCOMMON_SUPPORT for details.
+
+config VPL_LIBGENERIC_SUPPORT
+ bool "Support generic libraries"
+ default y if SPL_LIBGENERIC_SUPPORT
+ help
+ Enable support for generic U-Boot libraries within VPL. These
+ libraries include generic code to deal with device tree, hashing,
+ printf(), compression and the like. This option is enabled on many
+ boards. Enable this option to build the code in lib/ as part of a
+ VPL build.
+
+config VPL_DRIVERS_MISC
+ bool "Support misc drivers"
+ default y if TPL_DRIVERS_MISC
+ help
+ Enable miscellaneous drivers in VPL. These drivers perform various
+ tasks that don't fall nicely into other categories, Enable this
+ option to build the drivers in drivers/misc as part of a VPL
+ build, for those that support building in VPL (not all drivers do).
+
+config VPL_ENV_SUPPORT
+ bool "Support an environment"
+ help
+ Enable environment support in VPL. The U-Boot environment provides
+ a number of settings (essentially name/value pairs) which can
+ control many aspects of U-Boot's operation. Enabling this option will
+ make env_get() and env_set() available in VSPL.
+
+config VPL_GPIO
+ bool "Support GPIO in VPL"
+ default y if SPL_GPIO
+ help
+ Enable support for GPIOs (General-purpose Input/Output) in VPL.
+ GPIOs allow U-Boot to read the state of an input line (high or
+ low) and set the state of an output line. This can be used to
+ drive LEDs, control power to various system parts and read user
+ input. GPIOs can be useful in VPL to enable a 'sign-of-life' LED,
+ for example. Enable this option to build the drivers in
+ drivers/gpio as part of a VPL build.
+
+config VPL_HANDOFF
+ bool "Pass hand-off information from VPL to SPL and U-Boot proper"
+ depends on HANDOFF && VPL_BLOBLIST
+ default y
+ help
+ This option enables VPL to write handoff information. This can be
+ used to pass information like the size of SDRAM from VPL to U-Boot
+ proper. The information is also available to VPL if it is useful
+ there.
+
+config VPL_HASH
+ bool "Support hashing drivers in VPL"
+ depends on VPL
+ select SHA1
+ select SHA256
+ help
+ Enable hashing drivers in VPL. These drivers can be used to
+ accelerate secure boot processing in secure applications. Enable
+ this option to build system-specific drivers for hash acceleration
+ as part of a VPL build.
+
+config VPL_I2C_SUPPORT
+ bool "Support I2C in VPL"
+ default y if SPL_I2C_SUPPORT
+ help
+ Enable support for the I2C bus in VPL. Vee SPL_I2C_SUPPORT for
+ details.
+
+config VPL_PCH_SUPPORT
+ bool "Support PCH drivers"
+ default y if TPL_PCH_SUPPORT
+ help
+ Enable support for PCH (Platform Controller Hub) devices in VPL.
+ These are used to set up GPIOs and the SPI peripheral early in
+ boot. This enables the drivers in drivers/pch as part of a VPL
+ build.
+
+config VPL_PCI
+ bool "Support PCI drivers"
+ default y if SPL_PCI
+ help
+ Enable support for PCI in VPL. For platforms that need PCI to boot,
+ or must perform some init using PCI in VPL, this provides the
+ necessary driver support. This enables the drivers in drivers/pci
+ as part of a VPL build.
+
+config VPL_RTC
+ bool "Support RTC drivers"
+ help
+ Enable RTC (Real-time Clock) support in VPL. This includes support
+ for reading and setting the time. Some RTC devices also have some
+ non-volatile (battery-backed) memory which is accessible if
+ needed. This enables the drivers in drivers/rtc as part of a VPL
+ build.
+
+config VPL_SERIAL
+ bool "Support serial"
+ default y if TPL_SERIAL
+ select VPL_PRINTF
+ select VPL_STRTO
+ help
+ Enable support for serial in VPL. See SPL_SERIAL_SUPPORT for
+ details.
+
+config VPL_SIZE_LIMIT
+ hex "Maximum size of VPL image"
+ depends on VPL
+ default 0x0
+ help
+ Specifies the maximum length of the U-Boot VPL image.
+ If this value is zero, it is ignored.
+
+config VPL_SPI
+ bool "Support SPI drivers"
+ help
+ Enable support for using SPI in VPL. See SPL_SPI_SUPPORT for
+ details.
+
+config VPL_SPI_FLASH_SUPPORT
+ bool "Support SPI flash drivers"
+ help
+ Enable support for using SPI flash in VPL, and loading U-Boot from
+ SPI flash. SPI flash (Serial Peripheral Bus flash) is named after
+ the SPI bus that is used to connect it to a system. It is a simple
+ but fast bidirectional 4-wire bus (clock, chip select and two data
+ lines). This enables the drivers in drivers/mtd/spi as part of a
+ VPL build. This normally requires VPL_SPI_SUPPORT.
+
+config VPL_TEXT_BASE
+ hex "VPL Text Base"
+ default 0x0
+ help
+ The address in memory that VPL will be running from.
+
+endif # VPL
+
config SPL_AT91_MCK_BYPASS
bool "Use external clock signal as a source of main clock for AT91 platforms"
depends on ARCH_AT91