* (c) 1999 Machine Vision Holdings, Inc.
* (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org>
*
+ * Added 16-bit nand support
+ * (C) 2004 Texas Instruments
*/
#include <common.h>
#include <command.h>
#include <malloc.h>
#include <asm/io.h>
+#include <watchdog.h>
#ifdef CONFIG_SHOW_BOOT_PROGRESS
# include <status_led.h>
# define SHOW_BOOT_PROGRESS(arg)
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined CONFIG_NEW_NAND_CODE
-#include <linux/mtd/nftl.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ids.h>
+#include <jffs2/jffs2.h>
+
+#ifdef CONFIG_OMAP1510
+void archflashwp(void *archdata, int wp);
+#endif
+
+#define ROUND_DOWN(value,boundary) ((value) & (~((boundary)-1)))
/*
* Definition of the out of band configuration structure
int eccvalid_pos; /* position of ECC valid flag inside oob -1 = inactive */
} oob_config = { {0}, 0, 0};
-#define NAND_DEBUG
-#undef ECC_DEBUG
+#undef NAND_DEBUG
#undef PSYCHO_DEBUG
-#undef NFTL_DEBUG
+
+/* ****************** WARNING *********************
+ * When ALLOW_ERASE_BAD_DEBUG is non-zero the erase command will
+ * erase (or at least attempt to erase) blocks that are marked
+ * bad. This can be very handy if you are _sure_ that the block
+ * is OK, say because you marked a good block bad to test bad
+ * block handling and you are done testing, or if you have
+ * accidentally marked blocks bad.
+ *
+ * Erasing factory marked bad blocks is a _bad_ idea. If the
+ * erase succeeds there is no reliable way to find them again,
+ * and attempting to program or erase bad blocks can affect
+ * the data in _other_ (good) blocks.
+ */
+#define ALLOW_ERASE_BAD_DEBUG 0
#define CONFIG_MTD_NAND_ECC /* enable ECC */
-/* #define CONFIG_MTD_NAND_ECC_JFFS2 */
+#define CONFIG_MTD_NAND_ECC_JFFS2
+
+/* bits for nand_rw() `cmd'; or together as needed */
+#define NANDRW_READ 0x01
+#define NANDRW_WRITE 0x00
+#define NANDRW_JFFS2 0x02
+#define NANDRW_JFFS2_SKIP 0x04
/*
* Function Prototypes
*/
static void nand_print(struct nand_chip *nand);
-static int nand_rw (struct nand_chip* nand, int cmd,
+int nand_rw (struct nand_chip* nand, int cmd,
size_t start, size_t len,
size_t * retlen, u_char * buf);
-static int nand_erase(struct nand_chip* nand, size_t ofs, size_t len);
+int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean);
static int nand_read_ecc(struct nand_chip *nand, size_t start, size_t len,
size_t * retlen, u_char *buf, u_char *ecc_code);
static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len,
size_t * retlen, const u_char * buf, u_char * ecc_code);
+static void nand_print_bad(struct nand_chip *nand);
+static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len,
+ size_t * retlen, u_char * buf);
+static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len,
+ size_t * retlen, const u_char * buf);
+static int NanD_WaitReady(struct nand_chip *nand, int ale_wait);
#ifdef CONFIG_MTD_NAND_ECC
static int nand_correct_data (u_char *dat, u_char *read_ecc, u_char *calc_ecc);
static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code);
#endif
-static struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE] = {{0}};
+struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE] = {{0}};
/* Current NAND Device */
static int curr_device = -1;
printf ("Usage:\n%s\n", cmdtp->usage);
return 1;
case 2:
- if (strcmp(argv[1],"info") == 0) {
+ if (strcmp(argv[1],"info") == 0) {
int i;
putc ('\n');
printf ("\nDevice %d: ", curr_device);
nand_print(&nand_dev_desc[curr_device]);
return 0;
+
+ } else if (strcmp(argv[1],"bad") == 0) {
+ if ((curr_device < 0) || (curr_device >= CFG_MAX_NAND_DEVICE)) {
+ puts ("\nno devices available\n");
+ return 1;
+ }
+ printf ("\nDevice %d bad blocks:\n", curr_device);
+ nand_print_bad(&nand_dev_desc[curr_device]);
+ return 0;
+
}
printf ("Usage:\n%s\n", cmdtp->usage);
return 1;
return 0;
}
+ else if (strcmp(argv[1],"erase") == 0 && strcmp(argv[2], "clean") == 0) {
+ struct nand_chip* nand = &nand_dev_desc[curr_device];
+ ulong off = 0;
+ ulong size = nand->totlen;
+ int ret;
+
+ printf ("\nNAND erase: device %d offset %ld, size %ld ... ",
+ curr_device, off, size);
+
+ ret = nand_erase (nand, off, size, 1);
+
+ printf("%s\n", ret ? "ERROR" : "OK");
+
+ return ret;
+ }
printf ("Usage:\n%s\n", cmdtp->usage);
return 1;
default:
/* at least 4 args */
- if (strcmp(argv[1],"read") == 0 || strcmp(argv[1],"write") == 0) {
+ if (strncmp(argv[1], "read", 4) == 0 ||
+ strncmp(argv[1], "write", 5) == 0) {
ulong addr = simple_strtoul(argv[2], NULL, 16);
ulong off = simple_strtoul(argv[3], NULL, 16);
ulong size = simple_strtoul(argv[4], NULL, 16);
- int cmd = (strcmp(argv[1],"read") == 0);
+ int cmd = (strncmp(argv[1], "read", 4) == 0) ?
+ NANDRW_READ : NANDRW_WRITE;
int ret, total;
+ char* cmdtail = strchr(argv[1], '.');
+
+ if (cmdtail && !strncmp(cmdtail, ".oob", 2)) {
+ /* read out-of-band data */
+ if (cmd & NANDRW_READ) {
+ ret = nand_read_oob(nand_dev_desc + curr_device,
+ off, size, &total,
+ (u_char*)addr);
+ }
+ else {
+ ret = nand_write_oob(nand_dev_desc + curr_device,
+ off, size, &total,
+ (u_char*)addr);
+ }
+ return ret;
+ }
+ else if (cmdtail && !strncmp(cmdtail, ".jffs2", 2))
+ cmd |= NANDRW_JFFS2; /* skip bad blocks */
+ else if (cmdtail && !strncmp(cmdtail, ".jffs2s", 2)) {
+ cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */
+ if (cmd & NANDRW_READ)
+ cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */
+ }
+#ifdef SXNI855T
+ /* need ".e" same as ".j" for compatibility with older units */
+ else if (cmdtail && !strcmp(cmdtail, ".e"))
+ cmd |= NANDRW_JFFS2; /* skip bad blocks */
+#endif
+#ifdef CFG_NAND_SKIP_BAD_DOT_I
+ /* need ".i" same as ".jffs2s" for compatibility with older units (esd) */
+ /* ".i" for image -> read skips bad block (no 0xff) */
+ else if (cmdtail && !strcmp(cmdtail, ".i")) {
+ cmd |= NANDRW_JFFS2; /* skip bad blocks (on read too) */
+ if (cmd & NANDRW_READ)
+ cmd |= NANDRW_JFFS2_SKIP; /* skip bad blocks (on read too) */
+ }
+#endif /* CFG_NAND_SKIP_BAD_DOT_I */
+ else if (cmdtail) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
printf ("\nNAND %s: device %d offset %ld, size %ld ... ",
- cmd ? "read" : "write", curr_device, off, size);
+ (cmd & NANDRW_READ) ? "read" : "write",
+ curr_device, off, size);
ret = nand_rw(nand_dev_desc + curr_device, cmd, off, size,
&total, (u_char*)addr);
- printf ("%d bytes %s: %s\n", total, cmd ? "read" : "write",
+ printf (" %d bytes %s: %s\n", total,
+ (cmd & NANDRW_READ) ? "read" : "written",
ret ? "ERROR" : "OK");
return ret;
- } else if (strcmp(argv[1],"erase") == 0) {
- ulong off = simple_strtoul(argv[2], NULL, 16);
- ulong size = simple_strtoul(argv[3], NULL, 16);
+ } else if (strcmp(argv[1],"erase") == 0 &&
+ (argc == 4 || strcmp("clean", argv[2]) == 0)) {
+ int clean = argc == 5;
+ ulong off = simple_strtoul(argv[2 + clean], NULL, 16);
+ ulong size = simple_strtoul(argv[3 + clean], NULL, 16);
int ret;
printf ("\nNAND erase: device %d offset %ld, size %ld ... ",
curr_device, off, size);
- ret = nand_erase (nand_dev_desc + curr_device, off, size);
+ ret = nand_erase (nand_dev_desc + curr_device, off, size, clean);
printf("%s\n", ret ? "ERROR" : "OK");
}
}
+U_BOOT_CMD(
+ nand, 5, 1, do_nand,
+ "nand - NAND sub-system\n",
+ "info - show available NAND devices\n"
+ "nand device [dev] - show or set current device\n"
+ "nand read[.jffs2[s]] addr off size\n"
+ "nand write[.jffs2] addr off size - read/write `size' bytes starting\n"
+ " at offset `off' to/from memory address `addr'\n"
+ "nand erase [clean] [off size] - erase `size' bytes from\n"
+ " offset `off' (entire device if not specified)\n"
+ "nand bad - show bad blocks\n"
+ "nand read.oob addr off size - read out-of-band data\n"
+ "nand write.oob addr off size - read out-of-band data\n"
+);
+
int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
char *boot_device = NULL;
return 1;
}
- printf ("\nLoading from device %d: %s at 0x%lX (offset 0x%lX)\n",
+ printf ("\nLoading from device %d: %s at 0x%lx (offset 0x%lx)\n",
dev, nand_dev_desc[dev].name, nand_dev_desc[dev].IO_ADDR,
offset);
- if (nand_rw (nand_dev_desc + dev, 1, offset,
+ if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset,
SECTORSIZE, NULL, (u_char *)addr)) {
printf ("** Read error on %d\n", dev);
SHOW_BOOT_PROGRESS (-1);
return 1;
}
- if (nand_rw (nand_dev_desc + dev, 1, offset + SECTORSIZE, cnt,
+ if (nand_rw (nand_dev_desc + dev, NANDRW_READ, offset + SECTORSIZE, cnt,
NULL, (u_char *)(addr+SECTORSIZE))) {
printf ("** Read error on %d\n", dev);
SHOW_BOOT_PROGRESS (-1);
local_args[0] = argv[0];
local_args[1] = NULL;
- printf ("Automatic boot of image at addr 0x%08lX ...\n", addr);
+ printf ("Automatic boot of image at addr 0x%08lx ...\n", addr);
do_bootm (cmdtp, 0, 1, local_args);
rcode = 1;
return rcode;
}
-static int nand_rw (struct nand_chip* nand, int cmd,
+U_BOOT_CMD(
+ nboot, 4, 1, do_nandboot,
+ "nboot - boot from NAND device\n",
+ "loadAddr dev\n"
+);
+
+/* returns 0 if block containing pos is OK:
+ * valid erase block and
+ * not marked bad, or no bad mark position is specified
+ * returns 1 if marked bad or otherwise invalid
+ */
+int check_block (struct nand_chip *nand, unsigned long pos)
+{
+ int retlen;
+ uint8_t oob_data;
+ uint16_t oob_data16[6];
+ int page0 = pos & (-nand->erasesize);
+ int page1 = page0 + nand->oobblock;
+ int badpos = oob_config.badblock_pos;
+
+ if (pos >= nand->totlen)
+ return 1;
+
+ if (badpos < 0)
+ return 0; /* no way to check, assume OK */
+
+ if (nand->bus16) {
+ if (nand_read_oob(nand, (page0 + 0), 12, &retlen, (uint8_t *)oob_data16)
+ || (oob_data16[2] & 0xff00) != 0xff00)
+ return 1;
+ if (nand_read_oob(nand, (page1 + 0), 12, &retlen, (uint8_t *)oob_data16)
+ || (oob_data16[2] & 0xff00) != 0xff00)
+ return 1;
+ } else {
+ /* Note - bad block marker can be on first or second page */
+ if (nand_read_oob(nand, page0 + badpos, 1, &retlen, &oob_data)
+ || oob_data != 0xff
+ || nand_read_oob (nand, page1 + badpos, 1, &retlen, &oob_data)
+ || oob_data != 0xff)
+ return 1;
+ }
+
+ return 0;
+}
+
+/* print bad blocks in NAND flash */
+static void nand_print_bad(struct nand_chip* nand)
+{
+ unsigned long pos;
+
+ for (pos = 0; pos < nand->totlen; pos += nand->erasesize) {
+ if (check_block(nand, pos))
+ printf(" 0x%8.8lx\n", pos);
+ }
+ puts("\n");
+}
+
+/* cmd: 0: NANDRW_WRITE write, fail on bad block
+ * 1: NANDRW_READ read, fail on bad block
+ * 2: NANDRW_WRITE | NANDRW_JFFS2 write, skip bad blocks
+ * 3: NANDRW_READ | NANDRW_JFFS2 read, data all 0xff for bad blocks
+ * 7: NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP read, skip bad blocks
+ */
+int nand_rw (struct nand_chip* nand, int cmd,
size_t start, size_t len,
size_t * retlen, u_char * buf)
{
- int noecc, ret = 0, n, total = 0;
+ int ret = 0, n, total = 0;
char eccbuf[6];
-
- while(len) {
+ /* eblk (once set) is the start of the erase block containing the
+ * data being processed.
+ */
+ unsigned long eblk = ~0; /* force mismatch on first pass */
+ unsigned long erasesize = nand->erasesize;
+
+ while (len) {
+ if ((start & (-erasesize)) != eblk) {
+ /* have crossed into new erase block, deal with
+ * it if it is sure marked bad.
+ */
+ eblk = start & (-erasesize); /* start of block */
+ if (check_block(nand, eblk)) {
+ if (cmd == (NANDRW_READ | NANDRW_JFFS2)) {
+ while (len > 0 &&
+ start - eblk < erasesize) {
+ *(buf++) = 0xff;
+ ++start;
+ ++total;
+ --len;
+ }
+ continue;
+ } else if (cmd == (NANDRW_READ | NANDRW_JFFS2 | NANDRW_JFFS2_SKIP)) {
+ start += erasesize;
+ continue;
+ } else if (cmd == (NANDRW_WRITE | NANDRW_JFFS2)) {
+ /* skip bad block */
+ start += erasesize;
+ continue;
+ } else {
+ ret = 1;
+ break;
+ }
+ }
+ }
/* The ECC will not be calculated correctly if
less than 512 is written or read */
- noecc = (start != (start | 0x1ff) + 1) || (len < 0x200);
- if (cmd)
- ret = nand_read_ecc(nand, start, len,
- &n, (u_char*)buf,
- noecc ? NULL : eccbuf);
- else
- ret = nand_write_ecc(nand, start, len,
- &n, (u_char*)buf,
- noecc ? NULL : eccbuf);
+ /* Is request at least 512 bytes AND it starts on a proper boundry */
+ if((start != ROUND_DOWN(start, 0x200)) || (len < 0x200))
+ printf("Warning block writes should be at least 512 bytes and start on a 512 byte boundry\n");
+
+ if (cmd & NANDRW_READ) {
+ ret = nand_read_ecc(nand, start,
+ min(len, eblk + erasesize - start),
+ &n, (u_char*)buf, eccbuf);
+ } else {
+ ret = nand_write_ecc(nand, start,
+ min(len, eblk + erasesize - start),
+ &n, (u_char*)buf, eccbuf);
+ }
if (ret)
break;
}
static void nand_print(struct nand_chip *nand)
- {
- printf("%s at 0x%lX,\n"
- "\t %d chip%s %s, size %d MB, \n"
- "\t total size %ld MB, sector size %ld kB\n",
- nand->name, nand->IO_ADDR, nand->numchips,
- nand->numchips>1 ? "s" : "", nand->chips_name,
- 1 << (nand->chipshift - 20),
- nand->totlen >> 20, nand->erasesize >> 10);
-
- if (nand->nftl_found) {
- struct NFTLrecord *nftl = &nand->nftl;
- unsigned long bin_size, flash_size;
-
- bin_size = nftl->nb_boot_blocks * nand->erasesize;
- flash_size = (nftl->nb_blocks - nftl->nb_boot_blocks) * nand->erasesize;
-
- printf("\t NFTL boot record:\n"
- "\t Binary partition: size %ld%s\n"
- "\t Flash disk partition: size %ld%s, offset 0x%lx\n",
- bin_size > (1 << 20) ? bin_size >> 20 : bin_size >> 10,
- bin_size > (1 << 20) ? "MB" : "kB",
- flash_size > (1 << 20) ? flash_size >> 20 : flash_size >> 10,
- flash_size > (1 << 20) ? "MB" : "kB", bin_size);
- } else {
- puts ("\t No NFTL boot record found.\n");
+{
+ if (nand->numchips > 1) {
+ printf("%s at 0x%lx,\n"
+ "\t %d chips %s, size %d MB, \n"
+ "\t total size %ld MB, sector size %ld kB\n",
+ nand->name, nand->IO_ADDR, nand->numchips,
+ nand->chips_name, 1 << (nand->chipshift - 20),
+ nand->totlen >> 20, nand->erasesize >> 10);
+ }
+ else {
+ printf("%s at 0x%lx (", nand->chips_name, nand->IO_ADDR);
+ print_size(nand->totlen, ", ");
+ print_size(nand->erasesize, " sector)\n");
}
}
/* ------------------------------------------------------------------------- */
-/* This function is needed to avoid calls of the __ashrdi3 function. */
-static int shr(int val, int shift)
- {
- return val >> shift;
-}
-
-static int NanD_WaitReady(struct nand_chip *nand)
+static int NanD_WaitReady(struct nand_chip *nand, int ale_wait)
{
/* This is inline, to optimise the common case, where it's ready instantly */
int ret = 0;
- NAND_WAIT_READY(nand);
+#ifdef NAND_NO_RB /* in config file, shorter delays currently wrap accesses */
+ if(ale_wait)
+ NAND_WAIT_READY(nand); /* do the worst case 25us wait */
+ else
+ udelay(10);
+#else /* has functional r/b signal */
+ NAND_WAIT_READY(nand);
+#endif
return ret;
}
/* Lower the CLE line */
NAND_CTL_CLRCLE(nandptr);
- return NanD_WaitReady(nand);
+#ifdef NAND_NO_RB
+ if(command == NAND_CMD_RESET){
+ u_char ret_val;
+ NanD_Command(nand, NAND_CMD_STATUS);
+ do {
+ ret_val = READ_NAND(nandptr);/* wait till ready */
+ } while((ret_val & 0x40) != 0x40);
+ }
+#endif
+ return NanD_WaitReady(nand, 0);
}
/* NanD_Address: Set the current address for the flash chip */
static int NanD_Address(struct nand_chip *nand, int numbytes, unsigned long ofs)
- {
- unsigned long nandptr;
- int i;
+{
+ unsigned long nandptr;
+ int i;
- nandptr = nand->IO_ADDR;
+ nandptr = nand->IO_ADDR;
/* Assert the ALE (Address Latch Enable) line to the flash chip */
- NAND_CTL_SETALE(nandptr);
-
- /* Send the address */
- /* Devices with 256-byte page are addressed as:
- Column (bits 0-7), Page (bits 8-15, 16-23, 24-31)
- * there is no device on the market with page256
- and more than 24 bits.
- Devices with 512-byte page are addressed as:
- Column (bits 0-7), Page (bits 9-16, 17-24, 25-31)
- * 25-31 is sent only if the chip support it.
- * bit 8 changes the read command to be sent
- (NAND_CMD_READ0 or NAND_CMD_READ1).
+ NAND_CTL_SETALE(nandptr);
+
+ /* Send the address */
+ /* Devices with 256-byte page are addressed as:
+ * Column (bits 0-7), Page (bits 8-15, 16-23, 24-31)
+ * there is no device on the market with page256
+ * and more than 24 bits.
+ * Devices with 512-byte page are addressed as:
+ * Column (bits 0-7), Page (bits 9-16, 17-24, 25-31)
+ * 25-31 is sent only if the chip support it.
+ * bit 8 changes the read command to be sent
+ * (NAND_CMD_READ0 or NAND_CMD_READ1).
*/
- if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE)
- WRITE_NAND_ADDRESS(ofs, nandptr);
+ if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE)
+ WRITE_NAND_ADDRESS(ofs, nandptr);
- ofs = ofs >> nand->page_shift;
+ ofs = ofs >> nand->page_shift;
- if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE)
- for (i = 0; i < nand->pageadrlen; i++, ofs = ofs >> 8)
- WRITE_NAND_ADDRESS(ofs, nandptr);
+ if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE) {
+ for (i = 0; i < nand->pageadrlen; i++, ofs = ofs >> 8) {
+ WRITE_NAND_ADDRESS(ofs, nandptr);
+ }
+ }
- /* Lower the ALE line */
- NAND_CTL_CLRALE(nandptr);
+ /* Lower the ALE line */
+ NAND_CTL_CLRALE(nandptr);
- /* Wait for the chip to respond */
- return NanD_WaitReady(nand);
- }
+ /* Wait for the chip to respond */
+ return NanD_WaitReady(nand, 1);
+}
/* NanD_SelectChip: Select a given flash chip within the current floor */
static inline int NanD_SelectChip(struct nand_chip *nand, int chip)
{
/* Wait for it to be ready */
- return NanD_WaitReady(nand);
+ return NanD_WaitReady(nand, 0);
}
/* NanD_IdentChip: Identify a given NAND chip given {floor,chip} */
{
int mfr, id, i;
- NAND_ENABLE_CE(nand); /* set pin low */
+ NAND_ENABLE_CE(nand); /* set pin low */
/* Reset the chip */
if (NanD_Command(nand, NAND_CMD_RESET)) {
#ifdef NAND_DEBUG
printf("NanD_Command (reset) for %d,%d returned true\n",
floor, chip);
#endif
- NAND_DISABLE_CE(nand); /* set pin high */
+ NAND_DISABLE_CE(nand); /* set pin high */
return 0;
}
printf("NanD_Command (ReadID) for %d,%d returned true\n",
floor, chip);
#endif
- NAND_DISABLE_CE(nand); /* set pin high */
+ NAND_DISABLE_CE(nand); /* set pin high */
return 0;
}
id = READ_NAND(nand->IO_ADDR);
- NAND_DISABLE_CE(nand); /* set pin high */
- /* No response - return failure */
- if (mfr == 0xff || mfr == 0)
- {
- printf("NanD_Command (ReadID) got %d %d\n", mfr, id);
- return 0;
- }
+ NAND_DISABLE_CE(nand); /* set pin high */
+
+#ifdef NAND_DEBUG
+ printf("NanD_Command (ReadID) got %x %x\n", mfr, id);
+#endif
+ if (mfr == 0xff || mfr == 0) {
+ /* No response - return failure */
+ return 0;
+ }
/* Check it's the same as the first chip we identified.
* M-Systems say that any given nand_chip device should only
* contain _one_ type of flash part, although that's not a
* hardware restriction. */
if (nand->mfr) {
- if (nand->mfr == mfr && nand->id == id)
+ if (nand->mfr == mfr && nand->id == id) {
return 1; /* This is another the same the first */
- else
+ } else {
printf("Flash chip at floor %d, chip %d is different:\n",
floor, chip);
+ }
}
/* Print and store the manufacturer and ID codes. */
nand->chipshift =
nand_flash_ids[i].chipshift;
nand->page256 = nand_flash_ids[i].page256;
+ nand->eccsize = 256;
if (nand->page256) {
nand->oobblock = 256;
nand->oobsize = 8;
nand->oobsize = 16;
nand->page_shift = 9;
}
- nand->pageadrlen =
- nand_flash_ids[i].pageadrlen;
- nand->erasesize =
- nand_flash_ids[i].erasesize;
- nand->chips_name =
- nand_flash_ids[i].name;
- return 1;
+ nand->pageadrlen = nand_flash_ids[i].pageadrlen;
+ nand->erasesize = nand_flash_ids[i].erasesize;
+ nand->chips_name = nand_flash_ids[i].name;
+ nand->bus16 = nand_flash_ids[i].bus16;
+ return 1;
}
return 0;
}
/* If there are none at all that we recognise, bail */
if (!nand->numchips) {
- puts ("No flash chips recognised.\n");
+#ifdef NAND_DEBUG
+ puts ("No NAND flash chips recognised.\n");
+#endif
return;
}
nand->numchips, nand->totlen >> 20);
#endif
}
-#ifdef CONFIG_MTD_NAND_ECC
-/* we need to be fast here, 1 us per read translates to 1 second per meg */
-static void nand_fast_copy (unsigned char *source, unsigned char *dest, long cntr)
- {
- while (cntr > 16)
- {
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- *dest++ = *source++;
- cntr -= 16;
- }
- while (cntr > 0)
- {
- *dest++ = *source++;
- cntr--;
- }
- }
-#endif
+
/* we need to be fast here, 1 us per read translates to 1 second per meg */
-static void nand_fast_read(unsigned char *data_buf, int cntr, unsigned long nandptr)
- {
- while (cntr > 16)
- {
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- *data_buf++ = READ_NAND(nandptr);
- cntr -= 16;
- }
- while (cntr > 0)
- {
- *data_buf++ = READ_NAND(nandptr);
- cntr--;
- }
- }
-
-/* This routine is made available to other mtd code via
- * inter_module_register. It must only be accessed through
- * inter_module_get which will bump the use count of this module. The
- * addresses passed back in mtd are valid as long as the use count of
- * this module is non-zero, i.e. between inter_module_get and
- * inter_module_put. Keith Owens <kaos@ocs.com.au> 29 Oct 2000.
- */
+static void NanD_ReadBuf (struct nand_chip *nand, u_char * data_buf, int cntr)
+{
+ unsigned long nandptr = nand->IO_ADDR;
+
+ NanD_Command (nand, NAND_CMD_READ0);
+
+ if (nand->bus16) {
+ u16 val;
+
+ while (cntr >= 16) {
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ cntr -= 16;
+ }
+
+ while (cntr > 0) {
+ val = READ_NAND (nandptr);
+ *data_buf++ = val & 0xff;
+ *data_buf++ = val >> 8;
+ cntr -= 2;
+ }
+ } else {
+ while (cntr >= 16) {
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ *data_buf++ = READ_NAND (nandptr);
+ cntr -= 16;
+ }
+
+ while (cntr > 0) {
+ *data_buf++ = READ_NAND (nandptr);
+ cntr--;
+ }
+ }
+}
/*
* NAND read with ECC
u_char *data_poi;
u_char ecc_calc[6];
#endif
- unsigned long nandptr = nand->IO_ADDR;
/* Do not allow reads past end of device */
if ((start + len) > nand->totlen) {
- printf ("nand_read_ecc: Attempt read beyond end of device %x %x %x\n", (uint) start, (uint) len, (uint) nand->totlen);
+ printf ("%s: Attempt read beyond end of device %x %x %x\n",
+ __FUNCTION__, (uint) start, (uint) len, (uint) nand->totlen);
*retlen = 0;
return -1;
}
/* First we calculate the starting page */
- page = shr(start, nand->page_shift);
+ /*page = shr(start, nand->page_shift);*/
+ page = start >> nand->page_shift;
/* Get raw starting column */
col = start & (nand->oobblock - 1);
/* Loop until all data read */
while (*retlen < len) {
-
#ifdef CONFIG_MTD_NAND_ECC
-
/* Do we have this page in cache ? */
if (nand->cache_page == page)
goto readdata;
/* Send the read command */
NanD_Command(nand, NAND_CMD_READ0);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
+ if (nand->bus16) {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
+
/* Read in a page + oob data */
- nand_fast_read(nand->data_buf, nand->oobblock + nand->oobsize, nandptr);
+ NanD_ReadBuf(nand, nand->data_buf, nand->oobblock + nand->oobsize);
/* copy data into cache, for read out of cache and if ecc fails */
- if (nand->data_cache)
- memcpy (nand->data_cache, nand->data_buf, nand->oobblock + nand->oobsize);
+ if (nand->data_cache) {
+ memcpy (nand->data_cache, nand->data_buf,
+ nand->oobblock + nand->oobsize);
+ }
/* Pick the ECC bytes out of the oob data */
- for (j = 0; j < 6; j++)
+ for (j = 0; j < 6; j++) {
ecc_code[j] = nand->data_buf[(nand->oobblock + oob_config.ecc_pos[j])];
+ }
/* Calculate the ECC and verify it */
/* If block was not written with ECC, skip ECC */
nand_calculate_ecc (&nand->data_buf[0], &ecc_calc[0]);
switch (nand_correct_data (&nand->data_buf[0], &ecc_code[0], &ecc_calc[0])) {
case -1:
- printf ("nand_read_ecc: " "Failed ECC read, page 0x%08x\n", page);
+ printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page);
ecc_failed++;
break;
case 1:
case 2: /* transfer ECC corrected data to cache */
- memcpy (nand->data_cache, nand->data_buf, 256);
+ if (nand->data_cache)
+ memcpy (nand->data_cache, nand->data_buf, 256);
break;
}
}
nand_calculate_ecc (&nand->data_buf[256], &ecc_calc[3]);
switch (nand_correct_data (&nand->data_buf[256], &ecc_code[3], &ecc_calc[3])) {
case -1:
- printf ("nand_read_ecc: " "Failed ECC read, page 0x%08x\n", page);
+ printf ("%s: Failed ECC read, page 0x%08x\n", __FUNCTION__, page);
ecc_failed++;
break;
case 1:
data_poi = (nand->data_cache) ? nand->data_cache : nand->data_buf;
data_poi += col;
if ((*retlen + (nand->oobblock - col)) >= len) {
- nand_fast_copy (data_poi, buf + *retlen, len - *retlen);
+ memcpy (buf + *retlen, data_poi, len - *retlen);
*retlen = len;
} else {
- nand_fast_copy (data_poi, buf + *retlen, nand->oobblock - col);
+ memcpy (buf + *retlen, data_poi, nand->oobblock - col);
*retlen += nand->oobblock - col;
}
/* Set cache page address, invalidate, if ecc_failed */
#else
/* Send the read command */
NanD_Command(nand, NAND_CMD_READ0);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
+ if (nand->bus16) {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
+
/* Read the data directly into the return buffer */
if ((*retlen + (nand->oobblock - col)) >= len) {
- nand_fast_read(buf + *retlen, len - *retlen, nandptr);
+ NanD_ReadBuf(nand, buf + *retlen, len - *retlen);
*retlen = len;
/* We're done */
continue;
} else {
- nand_fast_read(buf + *retlen, nand->oobblock - col, nandptr);
+ NanD_ReadBuf(nand, buf + *retlen, nand->oobblock - col);
*retlen += nand->oobblock - col;
}
#endif
}
/* De-select the NAND device */
- NAND_DISABLE_CE(nand); /* set pin high */
+ NAND_DISABLE_CE(nand); /* set pin high */
/*
* Return success, if no ECC failures, else -EIO
return ecc_status ? -1 : 0;
}
-
/*
* Nand_page_program function is used for write and writev !
*/
{
int i;
-#ifdef CONFIG_MTD_NAND_ECC
unsigned long nandptr = nand->IO_ADDR;
+
+#ifdef CONFIG_MTD_NAND_ECC
#ifdef CONFIG_MTD_NAND_VERIFY_WRITE
int ecc_bytes = (nand->oobblock == 512) ? 6 : 3;
#endif
/* Read back previous written data, if col > 0 */
if (col) {
- NanD_Command(nand, NAND_CMD_READ0);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
- for (i = 0; i < col; i++)
- nand->data_buf[i] = READ_NAND (nandptr);
+ NanD_Command (nand, NAND_CMD_READ0);
+ if (nand->bus16) {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
+
+ if (nand->bus16) {
+ u16 val;
+
+ for (i = 0; i < col; i += 2) {
+ val = READ_NAND (nandptr);
+ nand->data_buf[i] = val & 0xff;
+ nand->data_buf[i + 1] = val >> 8;
+ }
+ } else {
+ for (i = 0; i < col; i++)
+ nand->data_buf[i] = READ_NAND (nandptr);
+ }
}
/* Calculate and write the ECC if we have enough data */
if ((col < nand->eccsize) && (last >= nand->eccsize)) {
nand_calculate_ecc (&nand->data_buf[0], &(ecc_code[0]));
- for (i = 0; i < 3; i++)
- nand->data_buf[(nand->oobblock + oob_config.ecc_pos[i])] = ecc_code[i];
- if (oob_config.eccvalid_pos != -1)
- nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] = 0xf0;
+ for (i = 0; i < 3; i++) {
+ nand->data_buf[(nand->oobblock +
+ oob_config.ecc_pos[i])] = ecc_code[i];
+ }
+ if (oob_config.eccvalid_pos != -1) {
+ nand->data_buf[nand->oobblock +
+ oob_config.eccvalid_pos] = 0xf0;
+ }
}
/* Calculate and write the second ECC if we have enough data */
if ((nand->oobblock == 512) && (last == nand->oobblock)) {
nand_calculate_ecc (&nand->data_buf[256], &(ecc_code[3]));
- for (i = 3; i < 6; i++)
- nand->data_buf[(nand->oobblock + oob_config.ecc_pos[i])] = ecc_code[i];
- if (oob_config.eccvalid_pos != -1)
- nand->data_buf[nand->oobblock + oob_config.eccvalid_pos] &= 0x0f;
+ for (i = 3; i < 6; i++) {
+ nand->data_buf[(nand->oobblock +
+ oob_config.ecc_pos[i])] = ecc_code[i];
+ }
+ if (oob_config.eccvalid_pos != -1) {
+ nand->data_buf[nand->oobblock +
+ oob_config.eccvalid_pos] &= 0x0f;
+ }
}
#endif
/* Prepad for partial page programming !!! */
nand->data_buf[i] = 0xff;
/* Send command to begin auto page programming */
- NanD_Command(nand, NAND_CMD_SEQIN);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
+ NanD_Command (nand, NAND_CMD_READ0);
+ NanD_Command (nand, NAND_CMD_SEQIN);
+ if (nand->bus16) {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
/* Write out complete page of data */
- for (i = 0; i < (nand->oobblock + nand->oobsize); i++)
- WRITE_NAND(nand->data_buf[i], nand->IO_ADDR);
+ if (nand->bus16) {
+ for (i = 0; i < (nand->oobblock + nand->oobsize); i += 2) {
+ WRITE_NAND (nand->data_buf[i] +
+ (nand->data_buf[i + 1] << 8),
+ nand->IO_ADDR);
+ }
+ } else {
+ for (i = 0; i < (nand->oobblock + nand->oobsize); i++)
+ WRITE_NAND (nand->data_buf[i], nand->IO_ADDR);
+ }
/* Send command to actually program the data */
- NanD_Command(nand, NAND_CMD_PAGEPROG);
- NanD_Command(nand, NAND_CMD_STATUS);
-
+ NanD_Command (nand, NAND_CMD_PAGEPROG);
+ NanD_Command (nand, NAND_CMD_STATUS);
+#ifdef NAND_NO_RB
+ {
+ u_char ret_val;
+
+ do {
+ ret_val = READ_NAND (nandptr); /* wait till ready */
+ } while ((ret_val & 0x40) != 0x40);
+ }
+#endif
/* See if device thinks it succeeded */
- if (READ_NAND(nand->IO_ADDR) & 0x01) {
- printf ("nand_write_ecc: " "Failed write, page 0x%08x, ", page);
+ if (READ_NAND (nand->IO_ADDR) & 0x01) {
+ printf ("%s: Failed write, page 0x%08x, ", __FUNCTION__,
+ page);
return -1;
}
#ifdef CONFIG_MTD_NAND_VERIFY_WRITE
/* Send command to read back the page */
if (col < nand->eccsize)
- NanD_Command(nand, NAND_CMD_READ0);
+ NanD_Command (nand, NAND_CMD_READ0);
else
- NanD_Command(nand, NAND_CMD_READ1);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
+ NanD_Command (nand, NAND_CMD_READ1);
+ if (nand->bus16) {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
/* Loop through and verify the data */
- for (i = col; i < last; i++) {
- if (nand->data_buf[i] != readb (nand->IO_ADDR)) {
- printf ("nand_write_ecc: " "Failed write verify, page 0x%08x ", page);
- return -1;
+ if (nand->bus16) {
+ for (i = col; i < last; i = +2) {
+ if ((nand->data_buf[i] +
+ (nand->data_buf[i + 1] << 8)) != READ_NAND (nand->IO_ADDR)) {
+ printf ("%s: Failed write verify, page 0x%08x ",
+ __FUNCTION__, page);
+ return -1;
+ }
+ }
+ } else {
+ for (i = col; i < last; i++) {
+ if (nand->data_buf[i] != READ_NAND (nand->IO_ADDR)) {
+ printf ("%s: Failed write verify, page 0x%08x ",
+ __FUNCTION__, page);
+ return -1;
+ }
}
}
* We also want to check that the ECC bytes wrote
* correctly for the same reasons stated above.
*/
- NanD_Command(nand, NAND_CMD_READOOB);
- NanD_Address(nand, ADDR_COLUMN_PAGE, (page << nand->page_shift) + col);
- for (i = 0; i < nand->oobsize; i++)
- nand->data_buf[i] = readb (nand->IO_ADDR);
+ NanD_Command (nand, NAND_CMD_READOOB);
+ if (nand->bus16) {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + (col >> 1));
+ } else {
+ NanD_Address (nand, ADDR_COLUMN_PAGE,
+ (page << nand->page_shift) + col);
+ }
+ if (nand->bus16) {
+ for (i = 0; i < nand->oobsize; i += 2) {
+ u16 val;
+
+ val = READ_NAND (nand->IO_ADDR);
+ nand->data_buf[i] = val & 0xff;
+ nand->data_buf[i + 1] = val >> 8;
+ }
+ } else {
+ for (i = 0; i < nand->oobsize; i++) {
+ nand->data_buf[i] = READ_NAND (nand->IO_ADDR);
+ }
+ }
for (i = 0; i < ecc_bytes; i++) {
if ((nand->data_buf[(oob_config.ecc_pos[i])] != ecc_code[i]) && ecc_code[i]) {
- printf ("nand_write_ecc: Failed ECC write "
- "verify, page 0x%08x, " "%6i bytes were succesful\n", page, i);
+ printf ("%s: Failed ECC write "
+ "verify, page 0x%08x, "
+ "%6i bytes were succesful\n",
+ __FUNCTION__, page, i);
return -1;
}
}
-#endif
-#endif
+#endif /* CONFIG_MTD_NAND_ECC */
+#endif /* CONFIG_MTD_NAND_VERIFY_WRITE */
return 0;
}
+
static int nand_write_ecc (struct nand_chip* nand, size_t to, size_t len,
size_t * retlen, const u_char * buf, u_char * ecc_code)
{
/* Do not allow write past end of device */
if ((to + len) > nand->totlen) {
- printf ("nand_write_oob: Attempt to write past end of page\n");
+ printf ("%s: Attempt to write past end of page\n", __FUNCTION__);
return -1;
}
*retlen = 0;
/* Select the NAND device */
- NAND_ENABLE_CE(nand); /* set pin low */
+#ifdef CONFIG_OMAP1510
+ archflashwp(0,0);
+#endif
+#ifdef CFG_NAND_WP
+ NAND_WP_OFF();
+#endif
+
+ NAND_ENABLE_CE(nand); /* set pin low */
/* Check the WP bit */
- NanD_Command(nand, NAND_CMD_STATUS);
+ NanD_Command(nand, NAND_CMD_STATUS);
if (!(READ_NAND(nand->IO_ADDR) & 0x80)) {
- printf ("nand_write_ecc: Device is write protected!!!\n");
+ printf ("%s: Device is write protected!!!\n", __FUNCTION__);
ret = -1;
goto out;
}
nand->cache_page = -1;
/* Write data into buffer */
- if ((col + len) >= nand->oobblock)
- for (i = col, cnt = 0; i < nand->oobblock; i++, cnt++)
+ if ((col + len) >= nand->oobblock) {
+ for (i = col, cnt = 0; i < nand->oobblock; i++, cnt++) {
nand->data_buf[i] = buf[(*retlen + cnt)];
- else
- for (i = col, cnt = 0; cnt < (len - *retlen); i++, cnt++)
+ }
+ } else {
+ for (i = col, cnt = 0; cnt < (len - *retlen); i++, cnt++) {
nand->data_buf[i] = buf[(*retlen + cnt)];
+ }
+ }
/* We use the same function for write and writev !) */
ret = nand_write_page (nand, page, col, i, ecc_code);
if (ret)
out:
/* De-select the NAND device */
- NAND_DISABLE_CE(nand); /* set pin high */
+ NAND_DISABLE_CE(nand); /* set pin high */
+#ifdef CONFIG_OMAP1510
+ archflashwp(0,1);
+#endif
+#ifdef CFG_NAND_WP
+ NAND_WP_ON();
+#endif
return ret;
}
-#if 0 /* not used */
-/* Read a buffer from NanD */
-static void NanD_ReadBuf(struct nand_chip *nand, u_char * buf, int len)
-{
- unsigned long nandptr;
-
- nandptr = nand->IO_ADDR;
-
- for (; len > 0; len--)
- *buf++ = READ_NAND(nandptr);
-
-}
-/* Write a buffer to NanD */
-static void NanD_WriteBuf(struct nand_chip *nand, const u_char * buf, int len)
-{
- unsigned long nandptr;
- int i;
-
- nandptr = nand->IO_ADDR;
-
- if (len <= 0)
- return;
-
- for (i = 0; i < len; i++)
- WRITE_NAND(buf[i], nandptr);
-
-}
-
-/* find_boot_record: Find the NFTL Media Header and its Spare copy which contains the
- * various device information of the NFTL partition and Bad Unit Table. Update
- * the ReplUnitTable[] table accroding to the Bad Unit Table. ReplUnitTable[]
- * is used for management of Erase Unit in other routines in nftl.c and nftlmount.c
+/* read from the 16 bytes of oob data that correspond to a 512 byte
+ * page or 2 256-byte pages.
*/
-static int find_boot_record(struct NFTLrecord *nftl)
-{
- struct nftl_uci1 h1;
- struct nftl_oob oob;
- unsigned int block, boot_record_count = 0;
- int retlen;
- u8 buf[SECTORSIZE];
- struct NFTLMediaHeader *mh = &nftl->MediaHdr;
- unsigned int i;
-
- nftl->MediaUnit = BLOCK_NIL;
- nftl->SpareMediaUnit = BLOCK_NIL;
-
- /* search for a valid boot record */
- for (block = 0; block < nftl->nb_blocks; block++) {
- int ret;
-
- /* Check for ANAND header first. Then can whinge if it's found but later
- checks fail */
- if ((ret = nand_read_ecc(nftl->mtd, block * nftl->EraseSize, SECTORSIZE,
- &retlen, buf, NULL))) {
- static int warncount = 5;
-
- if (warncount) {
- printf("Block read at 0x%x failed\n", block * nftl->EraseSize);
- if (!--warncount)
- puts ("Further failures for this block will not be printed\n");
- }
- continue;
- }
-
- if (retlen < 6 || memcmp(buf, "ANAND", 6)) {
- /* ANAND\0 not found. Continue */
-#ifdef PSYCHO_DEBUG
- printf("ANAND header not found at 0x%x\n", block * nftl->EraseSize);
-#endif
- continue;
- }
-
-#ifdef NFTL_DEBUG
- printf("ANAND header found at 0x%x\n", block * nftl->EraseSize);
-#endif
-
- /* To be safer with BIOS, also use erase mark as discriminant */
- if ((ret = nand_read_oob(nftl->mtd, block * nftl->EraseSize + SECTORSIZE + 8,
- 8, &retlen, (char *)&h1) < 0)) {
-#ifdef NFTL_DEBUG
- printf("ANAND header found at 0x%x, but OOB data read failed\n",
- block * nftl->EraseSize);
-#endif
- continue;
- }
-
- /* OK, we like it. */
-
- if (boot_record_count) {
- /* We've already processed one. So we just check if
- this one is the same as the first one we found */
- if (memcmp(mh, buf, sizeof(struct NFTLMediaHeader))) {
-#ifdef NFTL_DEBUG
- printf("NFTL Media Headers at 0x%x and 0x%x disagree.\n",
- nftl->MediaUnit * nftl->EraseSize, block * nftl->EraseSize);
-#endif
- /* if (debug) Print both side by side */
- return -1;
- }
- if (boot_record_count == 1)
- nftl->SpareMediaUnit = block;
-
- boot_record_count++;
- continue;
- }
-
- /* This is the first we've seen. Copy the media header structure into place */
- memcpy(mh, buf, sizeof(struct NFTLMediaHeader));
-
- /* Do some sanity checks on it */
- if (mh->UnitSizeFactor != 0xff) {
- puts ("Sorry, we don't support UnitSizeFactor "
- "of != 1 yet.\n");
- return -1;
- }
-
- nftl->nb_boot_blocks = le16_to_cpu(mh->FirstPhysicalEUN);
- if ((nftl->nb_boot_blocks + 2) >= nftl->nb_blocks) {
- printf ("NFTL Media Header sanity check failed:\n"
- "nb_boot_blocks (%d) + 2 > nb_blocks (%d)\n",
- nftl->nb_boot_blocks, nftl->nb_blocks);
- return -1;
- }
-
- nftl->numvunits = le32_to_cpu(mh->FormattedSize) / nftl->EraseSize;
- if (nftl->numvunits > (nftl->nb_blocks - nftl->nb_boot_blocks - 2)) {
- printf ("NFTL Media Header sanity check failed:\n"
- "numvunits (%d) > nb_blocks (%d) - nb_boot_blocks(%d) - 2\n",
- nftl->numvunits,
- nftl->nb_blocks,
- nftl->nb_boot_blocks);
- return -1;
- }
-
- nftl->nr_sects = nftl->numvunits * (nftl->EraseSize / SECTORSIZE);
-
- /* If we're not using the last sectors in the device for some reason,
- reduce nb_blocks accordingly so we forget they're there */
- nftl->nb_blocks = le16_to_cpu(mh->NumEraseUnits) + le16_to_cpu(mh->FirstPhysicalEUN);
-
- /* read the Bad Erase Unit Table and modify ReplUnitTable[] accordingly */
- for (i = 0; i < nftl->nb_blocks; i++) {
- if ((i & (SECTORSIZE - 1)) == 0) {
- /* read one sector for every SECTORSIZE of blocks */
- if ((ret = nand_read_ecc(nftl->mtd, block * nftl->EraseSize +
- i + SECTORSIZE, SECTORSIZE,
- &retlen, buf, (char *)&oob)) < 0) {
- puts ("Read of bad sector table failed\n");
- return -1;
- }
- }
- /* mark the Bad Erase Unit as RESERVED in ReplUnitTable */
- if (buf[i & (SECTORSIZE - 1)] != 0xff)
- nftl->ReplUnitTable[i] = BLOCK_RESERVED;
- }
-
- nftl->MediaUnit = block;
- boot_record_count++;
-
- } /* foreach (block) */
-
- return boot_record_count?0:-1;
-}
static int nand_read_oob(struct nand_chip* nand, size_t ofs, size_t len,
- size_t * retlen, u_char * buf)
+ size_t * retlen, u_char * buf)
{
- int len256 = 0, ret;
- unsigned long nandptr;
+ int len256 = 0;
struct Nand *mychip;
+ int ret = 0;
- nandptr = nand->IO_ADDR;
-
- mychip = &nand->chips[shr(ofs, nand->chipshift)];
+ mychip = &nand->chips[ofs >> nand->chipshift];
/* update address for 2M x 8bit devices. OOB starts on the second */
/* page to maintain compatibility with nand_read_ecc. */
ofs -= 0x8;
}
+ NAND_ENABLE_CE(nand); /* set pin low */
NanD_Command(nand, NAND_CMD_READOOB);
- NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ if (nand->bus16) {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ ((ofs >> nand->page_shift) << nand->page_shift) +
+ ((ofs & (nand->oobblock - 1)) >> 1));
+ } else {
+ NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ }
/* treat crossing 8-byte OOB data for 2M x 8bit devices */
/* Note: datasheet says it should automaticaly wrap to the */
*retlen = len;
/* Reading the full OOB data drops us off of the end of the page,
- * causing the flash device to go into busy mode, so we need
- * to wait until ready 11.4.1 and Toshiba TC58256FT nands */
+ * causing the flash device to go into busy mode, so we need
+ * to wait until ready 11.4.1 and Toshiba TC58256FT nands */
- ret = NanD_WaitReady(nand);
+ ret = NanD_WaitReady(nand, 1);
+ NAND_DISABLE_CE(nand); /* set pin high */
return ret;
}
+
+/* write to the 16 bytes of oob data that correspond to a 512 byte
+ * page or 2 256-byte pages.
+ */
static int nand_write_oob(struct nand_chip* nand, size_t ofs, size_t len,
size_t * retlen, const u_char * buf)
{
int len256 = 0;
+ int i;
unsigned long nandptr = nand->IO_ADDR;
#ifdef PSYCHO_DEBUG
buf[8], buf[9], buf[14],buf[15]);
#endif
+ NAND_ENABLE_CE(nand); /* set pin low to enable chip */
+
/* Reset the chip */
NanD_Command(nand, NAND_CMD_RESET);
/* issue the Read2 command to set the pointer to the Spare Data Area. */
NanD_Command(nand, NAND_CMD_READOOB);
- NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ if (nand->bus16) {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ ((ofs >> nand->page_shift) << nand->page_shift) +
+ ((ofs & (nand->oobblock - 1)) >> 1));
+ } else {
+ NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ }
/* update address for 2M x 8bit devices. OOB starts on the second */
/* page to maintain compatibility with nand_read_ecc. */
/* issue the Serial Data In command to initial the Page Program process */
NanD_Command(nand, NAND_CMD_SEQIN);
- NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ if (nand->bus16) {
+ NanD_Address(nand, ADDR_COLUMN_PAGE,
+ ((ofs >> nand->page_shift) << nand->page_shift) +
+ ((ofs & (nand->oobblock - 1)) >> 1));
+ } else {
+ NanD_Address(nand, ADDR_COLUMN_PAGE, ofs);
+ }
/* treat crossing 8-byte OOB data for 2M x 8bit devices */
/* Note: datasheet says it should automaticaly wrap to the */
/* next OOB block, but it didn't work here. mf. */
if (nand->page256 && ofs + len > (ofs | 0x7) + 1) {
len256 = (ofs | 0x7) + 1 - ofs;
- NanD_WriteBuf(nand, buf, len256);
+ for (i = 0; i < len256; i++)
+ WRITE_NAND(buf[i], nandptr);
NanD_Command(nand, NAND_CMD_PAGEPROG);
NanD_Command(nand, NAND_CMD_STATUS);
- /* NanD_WaitReady() is implicit in NanD_Command */
-
+#ifdef NAND_NO_RB
+ { u_char ret_val;
+ do {
+ ret_val = READ_NAND(nandptr); /* wait till ready */
+ } while ((ret_val & 0x40) != 0x40);
+ }
+#endif
if (READ_NAND(nandptr) & 1) {
puts ("Error programming oob data\n");
/* There was an error */
+ NAND_DISABLE_CE(nand); /* set pin high */
*retlen = 0;
return -1;
}
NanD_Address(nand, ADDR_COLUMN_PAGE, ofs & (~0x1ff));
}
- NanD_WriteBuf(nand, &buf[len256], len - len256);
+ if (nand->bus16) {
+ for (i = len256; i < len; i += 2) {
+ WRITE_NAND(buf[i] + (buf[i+1] << 8), nandptr);
+ }
+ } else {
+ for (i = len256; i < len; i++)
+ WRITE_NAND(buf[i], nandptr);
+ }
NanD_Command(nand, NAND_CMD_PAGEPROG);
NanD_Command(nand, NAND_CMD_STATUS);
- /* NanD_WaitReady() is implicit in NanD_Command */
-
+#ifdef NAND_NO_RB
+ { u_char ret_val;
+ do {
+ ret_val = READ_NAND(nandptr); /* wait till ready */
+ } while ((ret_val & 0x40) != 0x40);
+ }
+#endif
if (READ_NAND(nandptr) & 1) {
puts ("Error programming oob data\n");
/* There was an error */
+ NAND_DISABLE_CE(nand); /* set pin high */
*retlen = 0;
return -1;
}
+ NAND_DISABLE_CE(nand); /* set pin high */
*retlen = len;
return 0;
}
-#endif
-static int nand_erase(struct nand_chip* nand, size_t ofs, size_t len)
+int nand_erase(struct nand_chip* nand, size_t ofs, size_t len, int clean)
{
+ /* This is defined as a structure so it will work on any system
+ * using native endian jffs2 (the default).
+ */
+ static struct jffs2_unknown_node clean_marker = {
+ JFFS2_MAGIC_BITMASK,
+ JFFS2_NODETYPE_CLEANMARKER,
+ 8 /* 8 bytes in this node */
+ };
unsigned long nandptr;
struct Nand *mychip;
+ int ret = 0;
if (ofs & (nand->erasesize-1) || len & (nand->erasesize-1)) {
printf ("Offset and size must be sector aligned, erasesize = %d\n",
- (int) nand->erasesize);
+ (int) nand->erasesize);
return -1;
}
nandptr = nand->IO_ADDR;
- /* FIXME: Do nand in the background. Use timers or schedule_task() */
- while(len) {
- mychip = &nand->chips[shr(ofs, nand->chipshift)];
+ /* Select the NAND device */
+#ifdef CONFIG_OMAP1510
+ archflashwp(0,0);
+#endif
+#ifdef CFG_NAND_WP
+ NAND_WP_OFF();
+#endif
+ NAND_ENABLE_CE(nand); /* set pin low */
- NanD_Command(nand, NAND_CMD_ERASE1);
- NanD_Address(nand, ADDR_PAGE, ofs);
- NanD_Command(nand, NAND_CMD_ERASE2);
+ /* Check the WP bit */
+ NanD_Command(nand, NAND_CMD_STATUS);
+ if (!(READ_NAND(nand->IO_ADDR) & 0x80)) {
+ printf ("nand_write_ecc: Device is write protected!!!\n");
+ ret = -1;
+ goto out;
+ }
- NanD_Command(nand, NAND_CMD_STATUS);
+ /* Check the WP bit */
+ NanD_Command(nand, NAND_CMD_STATUS);
+ if (!(READ_NAND(nand->IO_ADDR) & 0x80)) {
+ printf ("%s: Device is write protected!!!\n", __FUNCTION__);
+ ret = -1;
+ goto out;
+ }
- if (READ_NAND(nandptr) & 1) {
- printf("Error erasing at 0x%lx\n", (long)ofs);
- /* There was an error */
- goto callback;
+ /* FIXME: Do nand in the background. Use timers or schedule_task() */
+ while(len) {
+ /*mychip = &nand->chips[shr(ofs, nand->chipshift)];*/
+ mychip = &nand->chips[ofs >> nand->chipshift];
+
+ /* always check for bad block first, genuine bad blocks
+ * should _never_ be erased.
+ */
+ if (ALLOW_ERASE_BAD_DEBUG || !check_block(nand, ofs)) {
+ /* Select the NAND device */
+ NAND_ENABLE_CE(nand); /* set pin low */
+
+ NanD_Command(nand, NAND_CMD_ERASE1);
+ NanD_Address(nand, ADDR_PAGE, ofs);
+ NanD_Command(nand, NAND_CMD_ERASE2);
+
+ NanD_Command(nand, NAND_CMD_STATUS);
+
+#ifdef NAND_NO_RB
+ { u_char ret_val;
+ do {
+ ret_val = READ_NAND(nandptr); /* wait till ready */
+ } while ((ret_val & 0x40) != 0x40);
+ }
+#endif
+ if (READ_NAND(nandptr) & 1) {
+ printf ("%s: Error erasing at 0x%lx\n",
+ __FUNCTION__, (long)ofs);
+ /* There was an error */
+ ret = -1;
+ goto out;
+ }
+ if (clean) {
+ int n; /* return value not used */
+ int p, l;
+
+ /* clean marker position and size depend
+ * on the page size, since 256 byte pages
+ * only have 8 bytes of oob data
+ */
+ if (nand->page256) {
+ p = NAND_JFFS2_OOB8_FSDAPOS;
+ l = NAND_JFFS2_OOB8_FSDALEN;
+ } else {
+ p = NAND_JFFS2_OOB16_FSDAPOS;
+ l = NAND_JFFS2_OOB16_FSDALEN;
+ }
+
+ ret = nand_write_oob(nand, ofs + p, l, &n,
+ (u_char *)&clean_marker);
+ /* quit here if write failed */
+ if (ret)
+ goto out;
+ }
}
ofs += nand->erasesize;
len -= nand->erasesize;
}
- callback:
- return 0;
+out:
+ /* De-select the NAND device */
+ NAND_DISABLE_CE(nand); /* set pin high */
+#ifdef CONFIG_OMAP1510
+ archflashwp(0,1);
+#endif
+#ifdef CFG_NAND_WP
+ NAND_WP_ON();
+#endif
+
+ return ret;
}
static inline int nandcheck(unsigned long potential, unsigned long physadr)
{
-
-
return 0;
}
-void nand_probe(unsigned long physadr)
+unsigned long nand_probe(unsigned long physadr)
{
struct nand_chip *nand = NULL;
int i = 0, ChipID = 1;
oob_config.ecc_pos[3] = NAND_JFFS2_OOB_ECCPOS3;
oob_config.ecc_pos[4] = NAND_JFFS2_OOB_ECCPOS4;
oob_config.ecc_pos[5] = NAND_JFFS2_OOB_ECCPOS5;
- oob_config.badblock_pos = 5;
oob_config.eccvalid_pos = 4;
#else
oob_config.ecc_pos[0] = NAND_NOOB_ECCPOS0;
oob_config.ecc_pos[3] = NAND_NOOB_ECCPOS3;
oob_config.ecc_pos[4] = NAND_NOOB_ECCPOS4;
oob_config.ecc_pos[5] = NAND_NOOB_ECCPOS5;
- oob_config.badblock_pos = NAND_NOOB_BADBPOS;
oob_config.eccvalid_pos = NAND_NOOB_ECCVPOS;
#endif
+ oob_config.badblock_pos = 5;
for (i=0; i<CFG_MAX_NAND_DEVICE; i++) {
if (nand_dev_desc[i].ChipID == NAND_ChipID_UNKNOWN) {
- nand = nand_dev_desc + i;
+ nand = &nand_dev_desc[i];
break;
}
}
+ if (!nand)
+ return (0);
+
+ memset((char *)nand, 0, sizeof(struct nand_chip));
- if (curr_device == -1)
- curr_device = i;
+ nand->IO_ADDR = physadr;
+ nand->cache_page = -1; /* init the cache page */
+ NanD_ScanChips(nand);
+ if (nand->totlen == 0) {
+ /* no chips found, clean up and quit */
memset((char *)nand, 0, sizeof(struct nand_chip));
+ nand->ChipID = NAND_ChipID_UNKNOWN;
+ return (0);
+ }
- nand->cache_page = -1; /* init the cache page */
- nand->IO_ADDR = physadr;
- nand->ChipID = ChipID;
- NanD_ScanChips(nand);
- nand->data_buf = malloc (nand->oobblock + nand->oobsize);
- if (!nand->data_buf) {
- puts ("Cannot allocate memory for data structures.\n");
- return;
- }
+ nand->ChipID = ChipID;
+ if (curr_device == -1)
+ curr_device = i;
+
+ nand->data_buf = malloc (nand->oobblock + nand->oobsize);
+ if (!nand->data_buf) {
+ puts ("Cannot allocate memory for data structures.\n");
+ return (0);
+ }
+
+ return (nand->totlen);
}
#ifdef CONFIG_MTD_NAND_ECC
* Pre-calculated 256-way 1 byte column parity
*/
static const u_char nand_ecc_precalc_table[] = {
- 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00,
- 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65,
- 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66,
- 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03,
- 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69,
- 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c,
- 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f,
- 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a,
- 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30, 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a,
- 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55, 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f,
- 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56, 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c,
- 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33, 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69,
- 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59, 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03,
- 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c, 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66,
- 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f, 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65,
- 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00
+ 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a,
+ 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00,
+ 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f,
+ 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65,
+ 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c,
+ 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66,
+ 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59,
+ 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03,
+ 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33,
+ 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69,
+ 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56,
+ 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c,
+ 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55,
+ 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f,
+ 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30,
+ 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a,
+ 0x6a, 0x3f, 0x3c, 0x69, 0x33, 0x66, 0x65, 0x30,
+ 0x30, 0x65, 0x66, 0x33, 0x69, 0x3c, 0x3f, 0x6a,
+ 0x0f, 0x5a, 0x59, 0x0c, 0x56, 0x03, 0x00, 0x55,
+ 0x55, 0x00, 0x03, 0x56, 0x0c, 0x59, 0x5a, 0x0f,
+ 0x0c, 0x59, 0x5a, 0x0f, 0x55, 0x00, 0x03, 0x56,
+ 0x56, 0x03, 0x00, 0x55, 0x0f, 0x5a, 0x59, 0x0c,
+ 0x69, 0x3c, 0x3f, 0x6a, 0x30, 0x65, 0x66, 0x33,
+ 0x33, 0x66, 0x65, 0x30, 0x6a, 0x3f, 0x3c, 0x69,
+ 0x03, 0x56, 0x55, 0x00, 0x5a, 0x0f, 0x0c, 0x59,
+ 0x59, 0x0c, 0x0f, 0x5a, 0x00, 0x55, 0x56, 0x03,
+ 0x66, 0x33, 0x30, 0x65, 0x3f, 0x6a, 0x69, 0x3c,
+ 0x3c, 0x69, 0x6a, 0x3f, 0x65, 0x30, 0x33, 0x66,
+ 0x65, 0x30, 0x33, 0x66, 0x3c, 0x69, 0x6a, 0x3f,
+ 0x3f, 0x6a, 0x69, 0x3c, 0x66, 0x33, 0x30, 0x65,
+ 0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a,
+ 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00
};
*/
static void nand_calculate_ecc (const u_char *dat, u_char *ecc_code)
{
- u_char idx, reg1, reg2, reg3;
+ u_char idx, reg1, reg3;
int j;
/* Initialize variables */
- reg1 = reg2 = reg3 = 0;
+ reg1 = reg3 = 0;
ecc_code[0] = ecc_code[1] = ecc_code[2] = 0;
/* Build up column parity */
/* Get CP0 - CP5 from table */
idx = nand_ecc_precalc_table[dat[j]];
- reg1 ^= (idx & 0x3f);
+ reg1 ^= idx;
/* All bit XOR = 1 ? */
if (idx & 0x40) {
reg3 ^= (u_char) j;
- reg2 ^= ~((u_char) j);
}
}
/* Create non-inverted ECC code from line parity */
- nand_trans_result(reg2, reg3, ecc_code);
+ nand_trans_result((reg1 & 0x40) ? ~reg3 : reg3, reg3, ecc_code);
/* Calculate final ECC code */
ecc_code[0] = ~ecc_code[0];
if ((d1 | d2 | d3) == 0) {
/* No errors */
return 0;
- }
- else {
+ } else {
a = (d1 ^ (d1 >> 1)) & 0x55;
b = (d2 ^ (d2 >> 1)) & 0x55;
c = (d3 ^ (d3 >> 1)) & 0x54;
/* Should never happen */
return -1;
}
+
#endif
+
+#ifdef CONFIG_JFFS2_NAND
+
+int read_jffs2_nand(size_t start, size_t len,
+ size_t * retlen, u_char * buf, int nanddev)
+{
+ return nand_rw(nand_dev_desc + nanddev, NANDRW_READ | NANDRW_JFFS2,
+ start, len, retlen, buf);
+}
+
+#endif /* CONFIG_JFFS2_NAND */
+
+
#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */