config CMD_CRC32
bool "crc32"
+ select HASH
default y
help
Compute CRC32.
option is to use sandbox and pass the -d point to sandbox's
u-boot.dtb file.
+config CMD_IDE
+ bool "ide - Support for IDE drivers"
+ select IDE
+ help
+ Provides an 'ide' command which allows accessing the IDE drive,
+ reseting the IDE interface, printing the partition table and
+ geting device info. It also enables the 'diskboot' command which
+ permits booting from an IDE drive.
+
+config CMD_IO
+ bool "io - Support for performing I/O accesses"
+ help
+ Provides an 'iod' command to display I/O space and an 'iow' command
+ to write values to the I/O space. This can be useful for manually
+ checking the state of devices during boot when debugging device
+ drivers, etc.
+
+config CMD_IOTRACE
+ bool "iotrace - Support for tracing I/O activity"
+ help
+ Provides an 'iotrace' command which supports recording I/O reads and
+ writes in a trace buffer in memory . It also maintains a checksum
+ of the trace records (even if space is exhausted) so that the
+ sequence of I/O accesses can be verified.
+
+ When debugging drivers it is useful to see what I/O accesses were
+ done and in what order.
+
+ Even if the individual accesses are of little interest it can be
+ useful to verify that the access pattern is consistent each time
+ an operation is performed. In this case a checksum can be used to
+ characterise the operation of a driver. The checksum can be compared
+ across different runs of the operation to verify that the driver is
+ working properly.
+
+ In particular, when performing major refactoring of the driver, where
+ the access pattern should not change, the checksum provides assurance
+ that the refactoring work has not broken the driver.
+
+ This works by sneaking into the io.h heder for an architecture and
+ redirecting I/O accesses through iotrace's tracing mechanism.
+
+ For now no commands are provided to examine the trace buffer. The
+ format is fairly simple, so 'md' is a reasonable substitute.
+
+ Note: The checksum feature is only useful for I/O regions where the
+ contents do not change outside of software control. Where this is not
+ suitable you can fall back to manually comparing the addresses. It
+ might be useful to enhance tracing to only checksum the accesses and
+ not the data read/written.
+
config CMD_LOADB
bool "loadb"
default y
help
FPGA support.
+config CMD_FPGA_LOADBP
+ bool "fpga loadbp - load partial bitstream (Xilinx only)"
+ depends on CMD_FPGA
+ help
+ Supports loading an FPGA device from a bitstream buffer containing
+ a partial bitstream.
+
+config CMD_FPGA_LOADFS
+ bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)"
+ depends on CMD_FPGA
+ help
+ Supports loading an FPGA device from a FAT filesystem.
+
+config CMD_FPGA_LOADMK
+ bool "fpga loadmk - load bitstream from image"
+ depends on CMD_FPGA
+ help
+ Supports loading an FPGA device from a image generated by mkimage.
+
+config CMD_FPGA_LOADP
+ bool "fpga loadp - load partial bitstream"
+ depends on CMD_FPGA
+ help
+ Supports loading an FPGA device from a bitstream buffer containing
+ a partial bitstream.
+
+config CMD_FPGAD
+ bool "fpgad - dump FPGA registers"
+ help
+ (legacy, needs conversion to driver model)
+ Provides a way to dump FPGA registers by calling the board-specific
+ fpga_get_reg() function. This functions similarly to the 'md'
+ command.
+
+config CMD_FUSE
+ bool "fuse - support for the fuse subssystem"
+ help
+ (deprecated - needs conversion to driver model)
+ This allows reading, sensing, programming or overriding fuses
+ which control the behaviour of the device. The command uses the
+ fuse_...() API.
+
config CMD_REMOTEPROC
bool "remoteproc"
depends on REMOTEPROC
help
GPIO support.
+config CMD_FDC
+ bool "fdcboot - Boot from floppy device"
+ help
+ The 'fdtboot' command allows booting an image from a floppy disk.
+
endmenu
help
Acquire a network IP address using the link-local protocol
+config CMD_ETHSW
+ bool "ethsw"
+ help
+ Allow control of L2 Ethernet switch commands. These are supported
+ by the vsc9953 Ethernet driver at present. Sub-commands allow
+ operations such as enabling / disabling a port and
+ viewing/maintaining the filtering database (FDB)
+
endmenu
menu "Misc commands"
help
Run commands and summarize execution time.
+config CMD_GETTIME
+ bool "gettime - read elapsed time"
+ help
+ Enable the 'gettime' command which reads the elapsed time since
+ U-Boot started running. This shows the time in seconds and
+ milliseconds. See also the 'bootstage' command which provides more
+ flexibility for boot timing.
+
# TODO: rename to CMD_SLEEP
config CMD_MISC
bool "sleep"
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
+config CMD_HASH
+ bool "Support 'hash' command"
+ select HASH
+ help
+ This provides a way to hash data in memory using various supported
+ algorithms (such as SHA1, MD5, CRC32). The computed digest can be
+ saved to memory or to an environment variable. It is also possible
+ to verify a hash against data in memory.
+
config CMD_TPM
bool "Enable the 'tpm' command"
depends on TPM
help
Enables fsuuid command for filesystem UUID.
+config CMD_JFFS2
+ bool "jffs2 command"
+ select FS_JFFS2
+ help
+ Enables commands to support the JFFS2 (Journalling Flash File System
+ version 2) filesystem. This enables fsload, ls and fsinfo which
+ provide the ability to load files, list directories and obtain
+ filesystem information.
+
config CMD_MTDPARTS
depends on ARCH_SUNXI
bool "MTD partition support"