{
volatile pcmconf8xx_t *pcmp;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+ pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
return ((pcmp->pcmc_pipr >> 24) & 0xf);
}
/*
* Initialize SDRAM
*/
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
/*---------------------------------------------------------------------*/
/*---------------------------------------------------------------------*/
memctl->memc_mptpr = 0x0200; /* Divide by 32 WV */
- memctl->memc_mamr = CFG_MAMR_VAL & 0xFF7FFFFF; /* Bit 8 := "0" Kein Refresh WV */
- memctl->memc_mbmr = CFG_MBMR_VAL;
+ memctl->memc_mamr = CONFIG_SYS_MAMR_VAL & 0xFF7FFFFF; /* Bit 8 := "0" Kein Refresh WV */
+ memctl->memc_mbmr = CONFIG_SYS_MBMR_VAL;
/*---------------------------------------------------------------------*/
/* Initialize the Memory Controller registers, MPTPR, Chip Select 1 */
/* clock rate (16.67MHz) to allow proper operation for all ADS */
/* clock frequencies. */
/*---------------------------------------------------------------------*/
- memctl->memc_or1 = CFG_OR1_PRELIM;
- memctl->memc_br1 = CFG_BR1_PRELIM;
+ memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
/*-------------------------------------------------------------------*/
/* Wait at least 200 usec for DRAM to stabilize, this magic number */
memctl->memc_mamr = (memctl->memc_mamr | 0x04) & ~0x08;
- memctl->memc_br1 = CFG_BR1_PRELIM;
- memctl->memc_or1 = CFG_OR1_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
+ memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
/*---------------------------------------------------------------------*/
/* run MRS command in location 5-8 of UPMB. */
/*---------------------------------------------------------------------*/
/* rerstore MBMR value (4-beat refresh burst.) */
/*---------------------------------------------------------------------*/
- memctl->memc_mamr = CFG_MAMR_VAL | 0x00800000; /* Bit 8 := "1" Refresh Enable WV */
+ memctl->memc_mamr = CONFIG_SYS_MAMR_VAL | 0x00800000; /* Bit 8 := "1" Refresh Enable WV */
udelay(200);
/*
* Make sure that RTC has clock output enabled (triggers watchdog!)
*/
- val = i2c_reg_read (CFG_I2C_RTC_ADDR, 0x0D);
+ val = i2c_reg_read (CONFIG_SYS_I2C_RTC_ADDR, 0x0D);
val |= 0x80;
- i2c_reg_write (CFG_I2C_RTC_ADDR, 0x0D, val);
+ i2c_reg_write (CONFIG_SYS_I2C_RTC_ADDR, 0x0D, val);
/*
* Configure PHY to setup LED's correctly and use 100MBit, FD
return 0;
}
-
-
-#ifdef CONFIG_POST
-/*
- * Returns 1 if keys pressed to start the power-on long-running tests
- * Called from board_init_f().
- */
-int post_hotkeys_pressed (void)
-{
- return 0; /* No hotkeys supported */
-}
-#endif