break;
putc (buf[i]);
}
-#ifdef CONFIG_VIRTLAB2
- puts (" (Virtlab2)");
-#endif
+
putc ('\n');
return (0);
/* ------------------------------------------------------------------------- */
-phys_size_t initdram (int board_type)
+int dram_init(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size8, size9, size10;
long int size_b0 = 0;
long int size_b1 = 0;
+ int board_type = gd->board_type;
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
memctl->memc_or5 = CONFIG_SYS_OR5_ISP1362;
memctl->memc_br5 = CONFIG_SYS_BR5_ISP1362;
#endif /* CONFIG_ISP1362_USB */
- return (size_b0 + size_b1);
+ gd->ram_size = size_b0 + size_b1;
+
+ return 0;
}
/* ------------------------------------------------------------------------- */
immap->im_ioport.iop_padat &= ~0x0001; /* turn it off */
# endif
-#ifdef CONFIG_NSCU
- /* wake up ethernet module */
- immap->im_ioport.iop_pcpar &= ~0x0004; /* GPIO pin */
- immap->im_ioport.iop_pcdir |= 0x0004; /* output */
- immap->im_ioport.iop_pcso &= ~0x0004; /* for clarity */
- immap->im_ioport.iop_pcdat |= 0x0004; /* enable */
-#endif /* CONFIG_NSCU */
-
return (0);
}
#endif /* CONFIG_MISC_INIT_R */
}
}
-void ft_board_setup(void *blob, bd_t *bd)
+int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
ft_blob_update(blob, bd);
-}
-#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
-
-/* ---------------------------------------------------------------------------- */
-/* TK885D specific initializaion */
-/* ---------------------------------------------------------------------------- */
-#ifdef CONFIG_TK885D
-#include <miiphy.h>
-int last_stage_init(void)
-{
- const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY};
- unsigned short reg;
- int ret, i = 100;
- char *s;
-
- mii_init();
- /* Without this delay 0xff is read from the UART buffer later in
- * abortboot() and autoboot is aborted */
- udelay(10000);
- while (tstc() && i--)
- (void)getc();
-
- /* Check if auto-negotiation is prohibited */
- s = getenv("phy_auto_nego");
-
- if (!s || !strcmp(s, "on"))
- /* Nothing to do - autonegotiation by default */
- return 0;
-
- for (i = 0; i < 2; i++) {
- ret = miiphy_read("FEC", phy[i], MII_BMCR, ®);
- if (ret) {
- printf("Cannot read BMCR on PHY %d\n", phy[i]);
- return 0;
- }
- /* Auto-negotiation off, hard set full duplex, 100Mbps */
- ret = miiphy_write("FEC", phy[i],
- MII_BMCR, (reg | BMCR_SPEED100 |
- BMCR_FULLDPLX) & ~BMCR_ANENABLE);
- if (ret) {
- printf("Cannot write BMCR on PHY %d\n", phy[i]);
- return 0;
- }
- }
return 0;
}
-#endif
+#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */