Merge branch 'master' of git://git.denx.de/u-boot

[platform/kernel/u-boot.git] / board / ti / ks2_evm / README

diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README
index 6586fab..0fe5c3b 100644 (file)
--- a/board/ti/ks2_evm/README
+++ b/board/ti/ks2_evm/README
@@ -56,38 +56,31 @@ configs/k2l_evm_defconfig
 Supported boot modes:
  - SPI NOR boot
  - AEMIF NAND boot
+ - UART boot
 
 Supported image formats:
- - u-boot.bin: for loading and running u-boot.bin through Texas instruments
-               code composure studio (CCS)
+ - u-boot-dtb.bin: for loading and running u-boot-dtb.bin through
+               Texas Instruments code composure studio (CCS) and for UART boot.
  - u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
- - u-boot-nand.gph: gpimage for programming AEMIF NAND flash for NAND boot
+ - MLO: gpimage for programming AEMIF NAND flash for NAND boot
 
 Build instructions:
 ===================
 Examples for k2hk, for k2e and k2l just replace k2hk prefix accordingly.
 Don't forget to add ARCH=arm and CROSS_COMPILE.
 
-To build u-boot.bin
+To build u-boot-dtb.bin, u-boot-spi.gph, MLO:
   >make k2hk_evm_defconfig
-  >make u-boot.bin
-
-To build u-boot-spi.gph
-  >make k2hk_evm_defconfig
-  >make u-boot-spi.gph
-
-To build u-boot-nand.gph
-  >make k2hk_evm_defconfig
-  >make u-boot-nand.gph
+  >make
 
 Load and Run U-Boot on keystone EVMs using CCS
 =========================================
 
-Need Code Composer Studio (CCS) installed on a PC to load and run u-boot.bin
+Need Code Composer Studio (CCS) installed on a PC to load and run u-boot-dtb.bin
 on EVM. See instructions at below link for installing CCS on a Windows PC.
 http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started#
 Installing_Code_Composer_Studio
-Use u-boot.bin from the build folder for loading and running u-boot binary
+Use u-boot-dtb.bin from the build folder for loading and running u-boot binary
 on EVM. Follow instructions at
 K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup
 K2E  http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup
@@ -107,7 +100,7 @@ loading the u-boot binary on the target EVM. Instead do the following:-
    is connected: Unknown)" at the debug window (This is created once Target
    configuration is launched) and select "Connect Target".
 2. Once target connect is successful, choose Tools->Load Memory option from the
-   top level menu. At the Load Memory window, choose the file u-boot.bin
+   top level menu. At the Load Memory window, choose the file u-boot-dtb.bin
    through "Browse" button and click "next >" button. In the next window, enter
    Start address as 0xc001000, choose Type-size "32 bits" and click "Finish"
    button.
@@ -157,14 +150,25 @@ instructions:
 1. Start CCS and run U-boot as described above.
 2. Suspend Target. Select Run -> Suspend from top level menu
    CortexA15_1 (Free Running)"
-3. Load u-boot-nand.gph binary from build folder on to DDR address 0x87000000
+3. Load MLO binary from build folder on to DDR address 0x87000000
    through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM
    using CCS", but using address 0x87000000.
 4. Free Run the target as described earlier (step 4) to get u-boot prompt
 5. At the U-Boot console type following to setup u-boot environment variables.
-   setenv filesize <size in hex of u-boot-nand.gph rounded to hex 0x10000>
+   setenv filesize <size in hex of MLO rounded to hex 0x10000>
    run burn_uboot_nand
    Once u-boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
    to "ARM NAND Boot mode" as per instruction at
    http://processors.wiki.ti.com/index.php/*_Hardware_Setup.
 6. Power ON the EVM. The EVM now boots with u-boot image on the NAND flash.
+
+Load and Run U-Boot on keystone EVMs using UART download
+========================================================
+
+Open BMC and regular UART terminals.
+
+1. On the regular UART port start xmodem transfer of the u-boot-dtb.bin
+2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM
+   BMC> bootmode #4
+   MBC> reboot
+3. When xmodem is complete you should see the u-boot starts on the UART port