/*
- * (C) Copyright 2004-2008
+ * (C) Copyright 2004-2011
* Texas Instruments, <www.ti.com>
*
* Author :
#include <status_led.h>
#endif
#include <twl4030.h>
+#include <linux/mtd/nand.h>
#include <asm/io.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
+#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
-#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
#include <asm/mach-types.h>
+#include <asm/omap_musb.h>
+#include <asm/errno.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
#include "beagle.h"
+#include <command.h>
+
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
#define TWL4030_I2C_BUS 0
#define EXPANSION_EEPROM_I2C_BUS 1
#define TINCANTOOLS_TRAINER 0x04000100
#define TINCANTOOLS_SHOWDOG 0x03000100
#define KBADC_BEAGLEFPGA 0x01000600
-
+#define LW_BEAGLETOUCH 0x01000700
+#define BRAINMUX_LCDOG 0x01000800
+#define BRAINMUX_LCDOGTOUCH 0x02000800
+#define BBTOYS_WIFI 0x01000B00
+#define BBTOYS_VGA 0x02000B00
+#define BBTOYS_LCD 0x03000B00
+#define BCT_BRETTL3 0x01000F00
+#define BCT_BRETTL4 0x02000F00
#define BEAGLE_NO_EEPROM 0xffffffff
DECLARE_GLOBAL_DATA_PTR;
* GPIO173, GPIO172, GPIO171: 1 0 1 => C4
* GPIO173, GPIO172, GPIO171: 0 0 0 => xM
*/
-int get_board_revision(void)
+static int get_board_revision(void)
{
int revision;
- if (!omap_request_gpio(171) &&
- !omap_request_gpio(172) &&
- !omap_request_gpio(173)) {
-
- omap_set_gpio_direction(171, 1);
- omap_set_gpio_direction(172, 1);
- omap_set_gpio_direction(173, 1);
+ if (!gpio_request(171, "") &&
+ !gpio_request(172, "") &&
+ !gpio_request(173, "")) {
- revision = omap_get_gpio_datain(173) << 2 |
- omap_get_gpio_datain(172) << 1 |
- omap_get_gpio_datain(171);
+ gpio_direction_input(171);
+ gpio_direction_input(172);
+ gpio_direction_input(173);
- omap_free_gpio(171);
- omap_free_gpio(172);
- omap_free_gpio(173);
+ revision = gpio_get_value(173) << 2 |
+ gpio_get_value(172) << 1 |
+ gpio_get_value(171);
} else {
printf("Error: unable to acquire board revision GPIOs\n");
revision = -1;
return revision;
}
+#ifdef CONFIG_SPL_BUILD
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on both banks.
+ */
+void get_board_mem_timings(struct board_sdrc_timings *timings)
+{
+ int pop_mfr, pop_id;
+
+ /*
+ * We need to identify what PoP memory is on the board so that
+ * we know what timings to use. If we can't identify it then
+ * we know it's an xM. To map the ID values please see nand_ids.c
+ */
+ identify_nand_chip(&pop_mfr, &pop_id);
+
+ timings->mr = MICRON_V_MR_165;
+ switch (get_board_revision()) {
+ case REVISION_C4:
+ if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
+ /* 512MB DDR */
+ timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ break;
+ } else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xba) {
+ /* Beagleboard Rev C4, 512MB Nand/256MB DDR*/
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ break;
+ } else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
+ /* Beagleboard Rev C5, 256MB DDR */
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ break;
+ }
+ case REVISION_XM_A:
+ case REVISION_XM_B:
+ case REVISION_XM_C:
+ if (pop_mfr == 0) {
+ /* 256MB DDR */
+ timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_200;
+ timings->ctrlb = MICRON_V_ACTIMB_200;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+ } else {
+ /* 512MB DDR */
+ timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+ timings->ctrla = NUMONYX_V_ACTIMA_165;
+ timings->ctrlb = NUMONYX_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ }
+ break;
+ default:
+ /* Assume 128MB and Micron/165MHz timings to be safe */
+ timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+ timings->ctrla = MICRON_V_ACTIMA_165;
+ timings->ctrlb = MICRON_V_ACTIMB_165;
+ timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+ }
+}
+#endif
+
/*
* Routine: get_expansion_id
* Description: This function checks for expansion board by checking I2C
* bus 1 for the availability of an AT24C01B serial EEPROM.
* returns the device_vendor field from the EEPROM
*/
-unsigned int get_expansion_id(void)
+static unsigned int get_expansion_id(void)
{
i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS);
return expansion_config.device_vendor;
}
+#ifdef CONFIG_VIDEO_OMAP3
+/*
+ * Configure DSS to display background color on DVID
+ * Configure VENC to display color bar on S-Video
+ */
+static void beagle_display_init(void)
+{
+ omap3_dss_venc_config(&venc_config_std_tv, VENC_HEIGHT, VENC_WIDTH);
+ switch (get_board_revision()) {
+ case REVISION_AXBX:
+ case REVISION_CX:
+ case REVISION_C4:
+ omap3_dss_panel_config(&dvid_cfg);
+ break;
+ case REVISION_XM_A:
+ case REVISION_XM_B:
+ case REVISION_XM_C:
+ default:
+ omap3_dss_panel_config(&dvid_cfg_xm);
+ break;
+ }
+}
+
+/*
+ * Enable DVI power
+ */
+static void beagle_dvi_pup(void)
+{
+ uchar val;
+
+ switch (get_board_revision()) {
+ case REVISION_AXBX:
+ case REVISION_CX:
+ case REVISION_C4:
+ case REVISION_XM_A:
+ gpio_request(170, "");
+ gpio_direction_output(170, 0);
+ gpio_set_value(170, 1);
+ break;
+ case REVISION_XM_B:
+ case REVISION_XM_C:
+ default:
+ #define GPIODATADIR1 (TWL4030_BASEADD_GPIO+3)
+ #define GPIODATAOUT1 (TWL4030_BASEADD_GPIO+6)
+
+ i2c_read(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+ val |= 4;
+ i2c_write(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+
+ i2c_read(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+ val |= 4;
+ i2c_write(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+ break;
+ }
+}
+#endif
+
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .num_eps = 16,
+ .ram_bits = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_MUSB_HOST)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_MUSB_GADGET)
+ .mode = MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_MUSB_HOST or CONFIG_MUSB_GADGET"
+#endif
+ .config = &musb_config,
+ .power = 100,
+ .platform_ops = &omap2430_ops,
+ .board_data = &musb_board_data,
+};
+#endif
+
/*
* Routine: misc_init_r
* Description: Configure board specific parts
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
- struct control_prog_io *prog_io_base = (struct gpio *)OMAP34XX_CTRL_BASE;
+ struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
/* Enable i2c2 pullup resisters */
writel(~(PRG_I2C2_PULLUPRESX), &prog_io_base->io1);
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("beaglerev", "AxBx");
- setenv("mpurate", "600");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
setenv("beaglerev", "Cx");
- setenv("mpurate", "600");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
setenv("beaglerev", "C4");
- setenv("mpurate", "720");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
- case REVISION_XM:
+ case REVISION_XM_A:
printf("Beagle xM Rev A\n");
setenv("beaglerev", "xMA");
- setenv("mpurate", "1000");
+ MUX_BEAGLE_XM();
+ /* Set VAUX2 to 1.8V for EHCI PHY */
+ twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+ TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+ TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+ TWL4030_PM_RECEIVER_DEV_GRP_P1);
+ break;
+ case REVISION_XM_B:
+ printf("Beagle xM Rev B\n");
+ setenv("beaglerev", "xMB");
+ MUX_BEAGLE_XM();
+ /* Set VAUX2 to 1.8V for EHCI PHY */
+ twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+ TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+ TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+ TWL4030_PM_RECEIVER_DEV_GRP_P1);
+ break;
+ case REVISION_XM_C:
+ printf("Beagle xM Rev C\n");
+ setenv("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
break;
default:
printf("Beagle unknown 0x%02x\n", get_board_revision());
+ MUX_BEAGLE_XM();
+ /* Set VAUX2 to 1.8V for EHCI PHY */
+ twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+ TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+ TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+ TWL4030_PM_RECEIVER_DEV_GRP_P1);
}
switch (get_expansion_id()) {
MUX_KBADC_BEAGLEFPGA();
setenv("buddy", "beaglefpga");
break;
+ case LW_BEAGLETOUCH:
+ printf("Recognized Liquidware BeagleTouch board\n");
+ setenv("buddy", "beagletouch");
+ break;
+ case BRAINMUX_LCDOG:
+ printf("Recognized Brainmux LCDog board\n");
+ setenv("buddy", "lcdog");
+ break;
+ case BRAINMUX_LCDOGTOUCH:
+ printf("Recognized Brainmux LCDog Touch board\n");
+ setenv("buddy", "lcdogtouch");
+ break;
+ case BBTOYS_WIFI:
+ printf("Recognized BeagleBoardToys WiFi board\n");
+ MUX_BBTOYS_WIFI()
+ setenv("buddy", "bbtoys-wifi");
+ break;;
+ case BBTOYS_VGA:
+ printf("Recognized BeagleBoardToys VGA board\n");
+ break;;
+ case BBTOYS_LCD:
+ printf("Recognized BeagleBoardToys LCD board\n");
+ break;;
+ case BCT_BRETTL3:
+ printf("Recognized bct electronic GmbH brettl3 board\n");
+ break;
+ case BCT_BRETTL4:
+ printf("Recognized bct electronic GmbH brettl4 board\n");
+ break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
setenv(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
- twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
-
- /* Configure GPIOs to output */
- writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
- writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+ switch (get_board_revision()) {
+ case REVISION_XM_A:
+ case REVISION_XM_B:
+ twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
+ break;
+ default:
+ twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
+ break;
+ }
- /* Set GPIOs */
+ /* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+ /* Configure GPIOs to output */
+ writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
+ writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+
dieid_num_r();
+#ifdef CONFIG_VIDEO_OMAP3
+ beagle_dvi_pup();
+ beagle_display_init();
+ omap3_dss_enable();
+#endif
+
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+ musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
return 0;
}
MUX_BEAGLE();
}
-#ifdef CONFIG_GENERIC_MMC
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
int board_mmc_init(bd_t *bis)
{
- omap_mmc_init(0);
+ omap_mmc_init(0, 0, 0);
return 0;
}
#endif
+
+#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+/* Call usb_stop() before starting the kernel */
+void show_boot_progress(int val)
+{
+ if (val == BOOTSTAGE_ID_RUN_OS)
+ usb_stop();
+}
+
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
+};
+
+int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(int index)
+{
+ return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)
+int board_eth_init(bd_t *bis)
+{
+ return usb_eth_initialize(bis);
+}
+#endif