#include <i2c.h>
#include <miiphy.h>
#include <cpsw.h>
+#include <power/tps65217.h>
+#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
#include "board.h"
DECLARE_GLOBAL_DATA_PTR;
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
-/* MII mode defines */
-#define MII_MODE_ENABLE 0x0
-#define RGMII_MODE_ENABLE 0x3A
-
/* GPIO that controls power to DDR on EVM-SK */
#define GPIO_DDR_VTT_EN 7
(MT47H128M16RT25E_PHY_WR_DATA<<20) |
(MT47H128M16RT25E_PHY_WR_DATA<<10) |
(MT47H128M16RT25E_PHY_WR_DATA<<0)),
- .datauserank0delay = MT47H128M16RT25E_PHY_RANK0_DELAY,
- .datadldiff0 = PHY_DLL_LOCK_DIFF,
};
static const struct cmd_control ddr2_cmd_ctrl_data = {
.cmd0csratio = MT47H128M16RT25E_RATIO,
- .cmd0dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
.cmd0iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
.cmd1csratio = MT47H128M16RT25E_RATIO,
- .cmd1dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
.cmd1iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
.cmd2csratio = MT47H128M16RT25E_RATIO,
- .cmd2dldiff = MT47H128M16RT25E_DLL_LOCK_DIFF,
.cmd2iclkout = MT47H128M16RT25E_INVERT_CLKOUT,
};
.datawdsratio0 = MT41J128MJT125_WR_DQS,
.datafwsratio0 = MT41J128MJT125_PHY_FIFO_WE,
.datawrsratio0 = MT41J128MJT125_PHY_WR_DATA,
- .datadldiff0 = PHY_DLL_LOCK_DIFF,
};
static const struct ddr_data ddr3_beagleblack_data = {
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
- .datadldiff0 = PHY_DLL_LOCK_DIFF,
};
static const struct ddr_data ddr3_evm_data = {
.datawdsratio0 = MT41J512M8RH125_WR_DQS,
.datafwsratio0 = MT41J512M8RH125_PHY_FIFO_WE,
.datawrsratio0 = MT41J512M8RH125_PHY_WR_DATA,
- .datadldiff0 = PHY_DLL_LOCK_DIFF,
};
static const struct cmd_control ddr3_cmd_ctrl_data = {
.cmd0csratio = MT41J128MJT125_RATIO,
- .cmd0dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
.cmd0iclkout = MT41J128MJT125_INVERT_CLKOUT,
.cmd1csratio = MT41J128MJT125_RATIO,
- .cmd1dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
.cmd1iclkout = MT41J128MJT125_INVERT_CLKOUT,
.cmd2csratio = MT41J128MJT125_RATIO,
- .cmd2dldiff = MT41J128MJT125_DLL_LOCK_DIFF,
.cmd2iclkout = MT41J128MJT125_INVERT_CLKOUT,
};
static const struct cmd_control ddr3_beagleblack_cmd_ctrl_data = {
.cmd0csratio = MT41K256M16HA125E_RATIO,
- .cmd0dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd1csratio = MT41K256M16HA125E_RATIO,
- .cmd1dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd2csratio = MT41K256M16HA125E_RATIO,
- .cmd2dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};
static const struct cmd_control ddr3_evm_cmd_ctrl_data = {
.cmd0csratio = MT41J512M8RH125_RATIO,
- .cmd0dldiff = MT41J512M8RH125_DLL_LOCK_DIFF,
.cmd0iclkout = MT41J512M8RH125_INVERT_CLKOUT,
.cmd1csratio = MT41J512M8RH125_RATIO,
- .cmd1dldiff = MT41J512M8RH125_DLL_LOCK_DIFF,
.cmd1iclkout = MT41J512M8RH125_INVERT_CLKOUT,
.cmd2csratio = MT41J512M8RH125_RATIO,
- .cmd2dldiff = MT41J512M8RH125_DLL_LOCK_DIFF,
.cmd2iclkout = MT41J512M8RH125_INVERT_CLKOUT,
};
}
#endif
-#endif
+#define OSC (V_OSCK/1000000)
+const struct dpll_params dpll_ddr = {
+ 266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_evm_sk = {
+ 303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_bone_black = {
+ 400, OSC-1, 1, -1, -1, -1, -1};
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void am33xx_spl_board_init(void)
{
- __maybe_unused struct am335x_baseboard_id header;
+ struct am335x_baseboard_id header;
+ int mpu_vdd;
- /*
- * The ROM will only have set up sufficient pinmux to allow for the
- * first 4KiB NOR to be read, we must finish doing what we know of
- * the NOR mux in this space in order to continue.
- */
-#ifdef CONFIG_NOR_BOOT
- asm("stmfd sp!, {r2 - r4}");
- asm("movw r4, #0x8A4");
- asm("movw r3, #0x44E1");
- asm("orr r4, r4, r3, lsl #16");
- asm("mov r2, #9");
- asm("mov r3, #8");
- asm("gpmc_mux: str r2, [r4], #4");
- asm("subs r3, r3, #1");
- asm("bne gpmc_mux");
- asm("ldmfd sp!, {r2 - r4}");
-#endif
+ if (read_eeprom(&header) < 0)
+ puts("Could not get board ID.\n");
-#ifdef CONFIG_SPL_BUILD
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
- save_omap_boot_params();
-#endif
+ /* Get the frequency */
+ dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
+ if (board_is_bone(&header) || board_is_bone_lt(&header)) {
+ /* BeagleBone PMIC Code */
+ int usb_cur_lim;
-#if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT)
- /* Setup the PLLs and the clocks for the peripherals */
- pll_init();
+ /*
+ * Only perform PMIC configurations if board rev > A1
+ * on Beaglebone White
+ */
+ if (board_is_bone(&header) && !strncmp(header.version,
+ "00A1", 4))
+ return;
+
+ if (i2c_probe(TPS65217_CHIP_PM))
+ return;
+
+ /*
+ * On Beaglebone White we need to ensure we have AC power
+ * before increasing the frequency.
+ */
+ if (board_is_bone(&header)) {
+ uchar pmic_status_reg;
+ if (tps65217_reg_read(TPS65217_STATUS,
+ &pmic_status_reg))
+ return;
+ if (!(pmic_status_reg & TPS65217_PWR_SRC_AC_BITMASK)) {
+ puts("No AC power, disabling frequency switch\n");
+ return;
+ }
+ }
+
+ /*
+ * Override what we have detected since we know if we have
+ * a Beaglebone Black it supports 1GHz.
+ */
+ if (board_is_bone_lt(&header))
+ dpll_mpu_opp100.m = MPUPLL_M_1000;
+
+ /*
+ * Increase USB current limit to 1300mA or 1800mA and set
+ * the MPU voltage controller as needed.
+ */
+ if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+ } else {
+ usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+ mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+ }
+
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+ TPS65217_POWER_PATH,
+ usb_cur_lim,
+ TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+ puts("tps65217_reg_write failure\n");
+
+ /* Set DCDC3 (CORE) voltage to 1.125V */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+ TPS65217_DCDC_VOLT_SEL_1125MV)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+ /* Set DCDC2 (MPU) voltage */
+ if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+ puts("tps65217_voltage_update failure\n");
+ return;
+ }
+
+ /*
+ * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
+ * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
+ */
+ if (board_is_bone(&header)) {
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS1,
+ TPS65217_LDO_VOLTAGE_OUT_3_3,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+ } else {
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS1,
+ TPS65217_LDO_VOLTAGE_OUT_1_8,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+ }
+
+ if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+ TPS65217_DEFLS2,
+ TPS65217_LDO_VOLTAGE_OUT_3_3,
+ TPS65217_LDO_MASK))
+ puts("tps65217_reg_write failure\n");
+ } else {
+ int sil_rev;
+
+ /*
+ * The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all
+ * MPU frequencies we support we use a CORE voltage of
+ * 1.1375V. For MPU voltage we need to switch based on
+ * the frequency we are running at.
+ */
+ if (i2c_probe(TPS65910_CTRL_I2C_ADDR))
+ return;
+
+ /*
+ * Depending on MPU clock and PG we will need a different
+ * VDD to drive at that speed.
+ */
+ sil_rev = readl(&cdev->deviceid) >> 28;
+ mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev,
+ dpll_mpu_opp100.m);
+
+ /* Tell the TPS65910 to use i2c */
+ tps65910_set_i2c_control();
+
+ /* First update MPU voltage. */
+ if (tps65910_voltage_update(MPU, mpu_vdd))
+ return;
+
+ /* Second, update the CORE voltage. */
+ if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3))
+ return;
+
+ /* Set CORE Frequencies to OPP100 */
+ do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+ }
+
+ /* Set MPU Frequency to what we detected now that voltages are set */
+ do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+ struct am335x_baseboard_id header;
+
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+ if (read_eeprom(&header) < 0)
+ puts("Could not get board ID.\n");
- /* Enable RTC32K clock */
- rtc32k_enable();
+ if (board_is_evm_sk(&header))
+ return &dpll_ddr_evm_sk;
+ else if (board_is_bone_lt(&header))
+ return &dpll_ddr_bone_black;
+ else if (board_is_evm_15_or_later(&header))
+ return &dpll_ddr_evm_sk;
+ else
+ return &dpll_ddr;
+}
+void set_uart_mux_conf(void)
+{
#ifdef CONFIG_SERIAL1
enable_uart0_pin_mux();
#endif /* CONFIG_SERIAL1 */
#ifdef CONFIG_SERIAL6
enable_uart5_pin_mux();
#endif /* CONFIG_SERIAL6 */
+}
- uart_soft_reset();
+void set_mux_conf_regs(void)
+{
+ __maybe_unused struct am335x_baseboard_id header;
-#if defined(CONFIG_NOR_BOOT)
- /* We want our console now. */
- gd->baudrate = CONFIG_BAUDRATE;
- serial_init();
- gd->have_console = 1;
-#else
- gd = &gdata;
+ if (read_eeprom(&header) < 0)
+ puts("Could not get board ID.\n");
- preloader_console_init();
-#endif
+ enable_board_pin_mux(&header);
+}
+
+const struct ctrl_ioregs ioregs_evmsk = {
+ .cm0ioctl = MT41J128MJT125_IOCTRL_VALUE,
+ .cm1ioctl = MT41J128MJT125_IOCTRL_VALUE,
+ .cm2ioctl = MT41J128MJT125_IOCTRL_VALUE,
+ .dt0ioctl = MT41J128MJT125_IOCTRL_VALUE,
+ .dt1ioctl = MT41J128MJT125_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs_bonelt = {
+ .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+ .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs_evm15 = {
+ .cm0ioctl = MT41J512M8RH125_IOCTRL_VALUE,
+ .cm1ioctl = MT41J512M8RH125_IOCTRL_VALUE,
+ .cm2ioctl = MT41J512M8RH125_IOCTRL_VALUE,
+ .dt0ioctl = MT41J512M8RH125_IOCTRL_VALUE,
+ .dt1ioctl = MT41J512M8RH125_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs = {
+ .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+ .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
+};
+
+void sdram_init(void)
+{
+ __maybe_unused struct am335x_baseboard_id header;
- /* Initalize the board header */
- enable_i2c0_pin_mux();
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
if (read_eeprom(&header) < 0)
puts("Could not get board ID.\n");
- enable_board_pin_mux(&header);
if (board_is_evm_sk(&header)) {
/*
* EVM SK 1.2A and later use gpio0_7 to enable DDR3.
}
if (board_is_evm_sk(&header))
- config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
+ config_ddr(303, &ioregs_evmsk, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
else if (board_is_bone_lt(&header))
- config_ddr(400, MT41K256M16HA125E_IOCTRL_VALUE,
+ config_ddr(400, &ioregs_bonelt,
&ddr3_beagleblack_data,
&ddr3_beagleblack_cmd_ctrl_data,
&ddr3_beagleblack_emif_reg_data, 0);
else if (board_is_evm_15_or_later(&header))
- config_ddr(303, MT41J512M8RH125_IOCTRL_VALUE, &ddr3_evm_data,
+ config_ddr(303, &ioregs_evm15, &ddr3_evm_data,
&ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);
else
- config_ddr(266, MT47H128M16RT25E_IOCTRL_VALUE, &ddr2_data,
+ config_ddr(266, &ioregs, &ddr2_data,
&ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
-#ifdef CONFIG_NOR
- const u32 gpmc_nor[GPMC_MAX_REG] = { STNOR_GPMC_CONFIG1,
- STNOR_GPMC_CONFIG2, STNOR_GPMC_CONFIG3, STNOR_GPMC_CONFIG4,
- STNOR_GPMC_CONFIG5, STNOR_GPMC_CONFIG6, STNOR_GPMC_CONFIG7 };
+#if defined(CONFIG_HW_WATCHDOG)
+ hw_watchdog_init();
#endif
- gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
-
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
gpmc_init();
-
-#ifdef CONFIG_NOR
- /* Reconfigure CS0 for NOR instead of NAND. */
- enable_gpmc_cs_config(gpmc_nor, &gpmc_cfg->cs[0],
- CONFIG_SYS_FLASH_BASE, GPMC_SIZE_16M);
#endif
-
return 0;
}
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
PHY_INTERFACE_MODE_MII;
} else {
- writel(RGMII_MODE_ENABLE, &cdev->miisel);
+ writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
PHY_INTERFACE_MODE_RGMII;
}
projects / platform / kernel / u-boot.git / blobdiff