video: Drop CONFIG_VIDEO

[platform/kernel/u-boot.git] / board / technexion / pico-imx7d / README

diff --git a/board/technexion/pico-imx7d/README b/board/technexion/pico-imx7d/README
index 24eb97e..e8f5082 100644 (file)
--- a/board/technexion/pico-imx7d/README
+++ b/board/technexion/pico-imx7d/README
@@ -11,7 +11,7 @@ $ make mrproper
 $ make pico-imx7d_defconfig
 $ make
 
-This generates the SPL and u-boot.img binaries.
+This generates the SPL and u-boot-dtb.img binaries.
 
 1. Loading U-Boot via USB Serial Download Protocol
 
@@ -26,17 +26,21 @@ Connect a USB to serial adapter between the host PC and pico.
 
 Connect a USB cable between the OTG pico port and the host PC.
 
+Note: Some computers may be a bit strict with USB current draw and will
+shut down their ports if the draw is too high. The solution for that is
+to use an externally powered USB hub between the board and the host computer.
+
 Open a terminal program such as minicom.
 
-Copy SPL and u-boot.img to the imx_usb_loader folder.
+Copy SPL and u-boot-dtb.img to the imx_usb_loader folder.
 
 Load the SPL binary via USB:
 
 $ sudo ./imx_usb SPL
 
-Load the u-boot.img binary via USB:
+Load the u-boot-dtb.img binary via USB:
 
-$ sudo ./imx_usb u-boot.img
+$ sudo ./imx_usb u-boot-dtb.img
 
 Then U-Boot starts and its messages appear in the console program.
 
@@ -51,14 +55,104 @@ Run the DFU agent so we can flash the new images using dfu-util tool:
 
 => dfu 0 mmc 0
 
-Flash SPL and u-boot.img into the eMMC running the following commands on a PC:
+Flash SPL and u-boot-dtb.img into the eMMC running the following commands on a PC:
 
 $ sudo dfu-util -D SPL -a spl
 
-$ sudo dfu-util -D u-boot.img -a u-boot
+$ sudo dfu-util -D u-boot-dtb.img -a u-boot
 
 Remove power from the pico board.
 
 Put pico board into normal boot mode.
 
 Power up the board and the new updated U-Boot should boot from eMMC.
+
+Booting in Falcon mode
+======================
+
+Generate a uImage kernel:
+
+$ make imx_v6_v7_defconfig (Using the default imx_v6_v7_defconfig configuration
+just for an example. In order to boot faster the user should customize the
+defconfig by only enabling the minimal required drivers).
+
+$ make -j4 uImage LOADADDR=0x80008000
+
+$ cp arch/arm/boot/uImage /tftpboot
+$ cp arch/arm/boot/dts/imx7d-pico-pi.dtb /tftpboot
+
+In the U-Boot prompt:
+
+Setup the server and board IP addresses:
+=> setenv serverip 192.168.0.10
+=> setenv ipaddr 192.168.0.11
+
+Get the dtb file:
+=> tftp ${fdt_addr} imx7d-pico-pi.dtb
+
+Get the kernel:
+=> tftp ${loadaddr} uImage
+
+Write the kernel at 2MB offset:
+=> mmc write ${loadaddr} 0x1000 0x5000
+
+Setup the bootargs:
+=> setenv bootargs 'console=ttymxc4,115200 root=/dev/mmcblk2p1 rootfstype=ext4 rootwait rw'
+
+Prepare args:
+=> spl export fdt ${loadaddr} - ${fdt_addr}
+## Booting kernel from Legacy Image at 80800000 ...
+   Image Name:   Linux-5.2.14
+   Image Type:   ARM Linux Kernel Image (uncompressed)
+   Data Size:    9077544 Bytes = 8.7 MiB
+   Load Address: 80008000
+   Entry Point:  80008000
+   Verifying Checksum ... OK
+## Flattened Device Tree blob at 83000000
+   Booting using the fdt blob at 0x83000000
+   Loading Kernel Image
+   Using Device Tree in place at 83000000, end 8300b615
+subcommand not supported
+subcommand not supported
+   Using Device Tree in place at 83000000, end 8300e615
+Argument image is now in RAM: 0x83000000
+=>
+
+Write 1MB of args data (0x800 sectors) to 1MB offset (0x800 sectors):
+
+=> mmc write ${fdt_addr} 0x800 0x800
+
+In order to boot with Falcon mode, activate the CONFIG_SPL_OS_BOOT
+option in the defconfig
+
+--- a/configs/pico-imx7d_defconfig
++++ b/configs/pico-imx7d_defconfig
+@@ -67,3 +67,4 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+ CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+ CONFIG_CI_UDC=y
++CONFIG_SPL_OS_BOOT=y
+
+Then rebuild U-Boot:
+
+$ make pico-imx7d_defconfig
+$ make -j4
+
+Launch UMS:
+=> ums 0 mmc 0
+
+Flash the new binaries:
+
+$ sudo dd if=SPL of=/dev/sdX bs=1k seek=1; sync
+$ sudo dd if=u-boot-dtb.img  of=/dev/sdX bs=1k seek=69; sync
+
+And then SPL binary will load and jump directly to the kernel:
+
+U-Boot SPL 2019.10-rc3-00284-g001c8ea94a-dirty (Sep 10 2019 - 12:46:01 -0300)
+Trying to boot from MMC1
+[    0.000000] Booting Linux on physical CPU 0x0
+[    0.000000] Linux version 5.2.14 (fabio@fabio-OptiPlex-7010) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #30 SMP Wed Sep 10 12:36:27 -03 2019
+[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
+[    0.000000] CPU: div instructions available: patching division code
+[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
+[    0.000000] OF: fdt: Machine model: TechNexion PICO-IMX7D Board and PI baseboard
+...