choice
prompt "Sunxi SoC Variant"
+ optional
config MACH_SUN4I
bool "sun4i (Allwinner A10)"
config MACH_SUN6I
bool "sun6i (Allwinner A31)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN7I
bool "sun7i (Allwinner A20)"
config MACH_SUN8I_A23
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN8I_A33
bool "sun8i (Allwinner A33)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN9I
+ bool "sun9i (Allwinner A80)"
+ select CPU_V7
+ select SUNXI_GEN_SUN6I
endchoice
---help---
Set the dram zq value.
+config DRAM_ODT_EN
+ bool "sunxi dram odt enable"
+ default n if !MACH_SUN8I_A23
+ default y if MACH_SUN8I_A23
+ ---help---
+ Select this to enable dram odt (on die termination).
+
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
int "sunxi dram emr1 value"
---help---
Set the dram controller emr1 value.
-config DRAM_ODT_EN
- int "sunxi dram odt_en value"
- default 0
- ---help---
- Set the dram controller odt_en parameter. This can be used to
- enable/disable the ODT feature.
-
config DRAM_TPR3
hex "sunxi dram tpr3 value"
default 0
endif
+if MACH_SUN8I_A23
+config DRAM_ODT_CORRECTION
+ int "sunxi dram odt correction value"
+ default 0
+ ---help---
+ Set the dram odt correction value (range -255 - 255). In allwinner
+ fex files, this option is found in bits 8-15 of the u32 odt_en variable
+ in the [dram] section. When bit 31 of the odt_en variable is set
+ then the correction is negative. Usually the value for this is 0.
+endif
+
config SYS_CLK_FREQ
default 912000000 if MACH_SUN7I
default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
default "sun6i" if MACH_SUN6I
default "sun7i" if MACH_SUN7I
default "sun8i" if MACH_SUN8I
+ default "sun9i" if MACH_SUN9I
config SYS_BOARD
default "sunxi"
config SYS_SOC
default "sunxi"
-config SPL_FEL
- bool "SPL/FEL mode support"
- depends on SPL
- default n
- help
- This enables support for Fast Early Loader (FEL) mode. This
- allows U-Boot to be loaded to the board over USB by the on-chip
- boot rom. U-Boot should be sent in two parts: SPL first, with
- 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
- 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
- shrinks the amount of SRAM available to SPL, so only enable it if
- you need FEL. Note that enabling this option only allows FEL to be
- used; it is still possible to boot U-Boot from boot media. U-Boot
- SPL detects when it is being loaded using FEL.
-
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
- depends on SPL_FEL
default n
---help---
Repurpose the SD card slot for getting access to the UART0 serial
Set this to enable various workarounds for old kernels, this results in
sub-optimal settings for newer kernels, only enable if needed.
+config MMC
+ depends on !UART0_PORT_F
+ default y if ARCH_SUNXI
+
config MMC0_CD_PIN
string "Card detect pin for mmc0"
default ""
Set the Vbus detect pin for usb0 (otg). This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config USB0_ID_DET
+ string "ID detect pin for usb0 (otg)"
+ default ""
+ ---help---
+ Set the ID detect pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
Set the enable pin for the external VGA DAC. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_COMPOSITE
+ boolean "Composite video output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting composite video.
+
config VIDEO_LCD_MODE
string "LCD panel timing details"
depends on VIDEO
LCD panel timing details string, leave empty if there is no LCD panel.
This is in drivers/video/videomodes.c: video_get_params() format, e.g.
x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+ Also see: http://linux-sunxi.org/LCD
config VIDEO_LCD_DCLK_PHASE
int "LCD panel display clock phase"
select VIDEO_LCD_SSD2828
select VIDEO_LCD_IF_PARALLEL
---help---
- 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+ 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+
+config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
+ bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip"
+ select VIDEO_LCD_ANX9804
+ select VIDEO_LCD_IF_PARALLEL
+ select VIDEO_LCD_PANEL_I2C
+ ---help---
+ Select this for eDP LCD panels with 4 lanes running at 1.62G,
+ connected via an ANX9804 bridge chip.
config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
bool "Hitachi tx18d42vm LCD panel"
endchoice
-config USB_MUSB_SUNXI
- bool "Enable sunxi OTG / DRC USB controller in host mode"
- default n
- ---help---
- Say y here to enable support for the sunxi OTG / DRC USB controller
- used on almost all sunxi boards. Note currently u-boot can only have
- one usb host controller enabled at a time, so enabling this on boards
- which also use the ehci host controller will result in build errors.
-
-config USB_KEYBOARD
- boolean "Enable USB keyboard support"
- default y
- ---help---
- Say Y here to add support for using a USB keyboard (typically used
- in combination with a graphical console).
-
config GMAC_TX_DELAY
int "GMAC Transmit Clock Delay Chain"
default 0
---help---
Set the GMAC Transmit Clock Delay Chain value.
-config NET
- default y
-
-config NETDEVICES
- default y
-
-config DM_ETH
- default y
-
-config DM_SERIAL
- default y
+config SPL_STACK_R_ADDR
+ default 0x4fe00000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN7I || MACH_SUN8I
+ default 0x2fe00000 if MACH_SUN9I
endif