if ARCH_SUNXI
+# Note only one of these may be selected at a time! But hidden choices are
+# not supported by Kconfig
+config SUNXI_GEN_SUN4I
+ bool
+ ---help---
+ Select this for sunxi SoCs which have resets and clocks set up
+ as the original A10 (mach-sun4i).
+
+config SUNXI_GEN_SUN6I
+ bool
+ ---help---
+ Select this for sunxi SoCs which have sun6i like periphery, like
+ separate ahb reset control registers, custom pmic bus, new style
+ watchdog, etc.
+
+
choice
prompt "Sunxi SoC Variant"
+ optional
config MACH_SUN4I
bool "sun4i (Allwinner A10)"
select CPU_V7
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
config MACH_SUN5I
bool "sun5i (Allwinner A13)"
select CPU_V7
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
config MACH_SUN6I
bool "sun6i (Allwinner A31)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN7I
bool "sun7i (Allwinner A20)"
select CPU_V7
select CPU_V7_HAS_NONSEC
select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-config MACH_SUN8I
+config MACH_SUN8I_A23
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN8I_A33
+ bool "sun8i (Allwinner A33)"
+ select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN6I
+ select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN9I
+ bool "sun9i (Allwinner A80)"
+ select CPU_V7
+ select SUNXI_GEN_SUN6I
endchoice
+# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
+config MACH_SUN8I
+ bool
+ default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
+
+
config DRAM_CLK
int "sunxi dram clock speed"
default 312 if MACH_SUN6I || MACH_SUN8I
---help---
Set the dram zq value.
+config DRAM_ODT_EN
+ bool "sunxi dram odt enable"
+ default n if !MACH_SUN8I_A23
+ default y if MACH_SUN8I_A23
+ ---help---
+ Select this to enable dram odt (on die termination).
+
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
int "sunxi dram emr1 value"
---help---
Set the dram controller emr1 value.
-config DRAM_ODT_EN
- int "sunxi dram odt_en value"
- default 0
- ---help---
- Set the dram controller odt_en parameter. This can be used to
- enable/disable the ODT feature.
-
config DRAM_TPR3
hex "sunxi dram tpr3 value"
default 0
endif
+if MACH_SUN8I_A23
+config DRAM_ODT_CORRECTION
+ int "sunxi dram odt correction value"
+ default 0
+ ---help---
+ Set the dram odt correction value (range -255 - 255). In allwinner
+ fex files, this option is found in bits 8-15 of the u32 odt_en variable
+ in the [dram] section. When bit 31 of the odt_en variable is set
+ then the correction is negative. Usually the value for this is 0.
+endif
+
config SYS_CLK_FREQ
default 912000000 if MACH_SUN7I
default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
default "sun6i" if MACH_SUN6I
default "sun7i" if MACH_SUN7I
default "sun8i" if MACH_SUN8I
+ default "sun9i" if MACH_SUN9I
config SYS_BOARD
default "sunxi"
config SYS_SOC
default "sunxi"
-config SPL_FEL
- bool "SPL/FEL mode support"
- depends on SPL
- default n
- help
- This enables support for Fast Early Loader (FEL) mode. This
- allows U-Boot to be loaded to the board over USB by the on-chip
- boot rom. U-Boot should be sent in two parts: SPL first, with
- 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
- 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
- shrinks the amount of SRAM available to SPL, so only enable it if
- you need FEL. Note that enabling this option only allows FEL to be
- used; it is still possible to boot U-Boot from boot media. U-Boot
- SPL detects when it is being loaded using FEL.
-
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
- depends on SPL_FEL
default n
---help---
Repurpose the SD card slot for getting access to the UART0 serial
at the same time, the system can be only booted in the FEL mode.
Only enable this if you really know what you are doing.
-config FDTFILE
- string "Default fdtfile env setting for this board"
-
config OLD_SUNXI_KERNEL_COMPAT
boolean "Enable workarounds for booting old kernels"
default n
Set this to enable various workarounds for old kernels, this results in
sub-optimal settings for newer kernels, only enable if needed.
+config MMC
+ depends on !UART0_PORT_F
+ default y if ARCH_SUNXI
+
config MMC0_CD_PIN
string "Card detect pin for mmc0"
default ""
---help---
See MMC0_CD_PIN help text.
+config MMC1_PINS
+ string "Pins for mmc1"
+ default ""
+ ---help---
+ Set the pins used for mmc1, when applicable. This takes a string in the
+ format understood by sunxi_name_to_gpio_bank, e.g. PH for port H.
+
+config MMC2_PINS
+ string "Pins for mmc2"
+ default ""
+ ---help---
+ See MMC1_PINS help text.
+
+config MMC3_PINS
+ string "Pins for mmc3"
+ default ""
+ ---help---
+ See MMC1_PINS help text.
+
config MMC_SUNXI_SLOT_EXTRA
int "mmc extra slot number"
default -1
Set the Vbus detect pin for usb0 (otg). This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config USB0_ID_DET
+ string "ID detect pin for usb0 (otg)"
+ default ""
+ ---help---
+ Set the ID detect pin for usb0 (otg). This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
config USB1_VBUS_PIN
string "Vbus enable pin for usb1 (ehci0)"
default "PH6" if MACH_SUN4I || MACH_SUN7I
---help---
See USB1_VBUS_PIN help text.
+config I2C0_ENABLE
+ bool "Enable I2C/TWI controller 0"
+ default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
+ default n if MACH_SUN6I || MACH_SUN8I
+ ---help---
+ This allows enabling I2C/TWI controller 0 by muxing its pins, enabling
+ its clock and setting up the bus. This is especially useful on devices
+ with slaves connected to the bus or with pins exposed through e.g. an
+ expansion port/header.
+
+config I2C1_ENABLE
+ bool "Enable I2C/TWI controller 1"
+ default n
+ ---help---
+ See I2C0_ENABLE help text.
+
+config I2C2_ENABLE
+ bool "Enable I2C/TWI controller 2"
+ default n
+ ---help---
+ See I2C0_ENABLE help text.
+
+if MACH_SUN6I || MACH_SUN7I
+config I2C3_ENABLE
+ bool "Enable I2C/TWI controller 3"
+ default n
+ ---help---
+ See I2C0_ENABLE help text.
+endif
+
+if MACH_SUN7I
+config I2C4_ENABLE
+ bool "Enable I2C/TWI controller 4"
+ default n
+ ---help---
+ See I2C0_ENABLE help text.
+endif
+
+config AXP_GPIO
+ boolean "Enable support for gpio-s on axp PMICs"
+ default n
+ ---help---
+ Say Y here to enable support for the gpio pins of the axp PMIC ICs.
+
config VIDEO
boolean "Enable graphical uboot console on HDMI, LCD or VGA"
default y
Set the enable pin for the external VGA DAC. This takes a string in the
format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+config VIDEO_COMPOSITE
+ boolean "Composite video output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting composite video.
+
config VIDEO_LCD_MODE
string "LCD panel timing details"
depends on VIDEO
LCD panel timing details string, leave empty if there is no LCD panel.
This is in drivers/video/videomodes.c: video_get_params() format, e.g.
x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+ Also see: http://linux-sunxi.org/LCD
config VIDEO_LCD_DCLK_PHASE
int "LCD panel display clock phase"
select VIDEO_LCD_SSD2828
select VIDEO_LCD_IF_PARALLEL
---help---
- 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+ 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
+
+config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
+ bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip"
+ select VIDEO_LCD_ANX9804
+ select VIDEO_LCD_IF_PARALLEL
+ select VIDEO_LCD_PANEL_I2C
+ ---help---
+ Select this for eDP LCD panels with 4 lanes running at 1.62G,
+ connected via an ANX9804 bridge chip.
config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
bool "Hitachi tx18d42vm LCD panel"
endchoice
-config USB_MUSB_SUNXI
- bool "Enable sunxi OTG / DRC USB controller in host mode"
- default n
- ---help---
- Say y here to enable support for the sunxi OTG / DRC USB controller
- used on almost all sunxi boards. Note currently u-boot can only have
- one usb host controller enabled at a time, so enabling this on boards
- which also use the ehci host controller will result in build errors.
-
-config USB_KEYBOARD
- boolean "Enable USB keyboard support"
- default y
- ---help---
- Say Y here to add support for using a USB keyboard (typically used
- in combination with a graphical console).
-
config GMAC_TX_DELAY
int "GMAC Transmit Clock Delay Chain"
default 0
---help---
Set the GMAC Transmit Clock Delay Chain value.
+config SPL_STACK_R_ADDR
+ default 0x4fe00000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN7I || MACH_SUN8I
+ default 0x2fe00000 if MACH_SUN9I
+
endif