static void irq_init(void)
{
-
+
/* disable global interrupt mode */
- write_mmcr_byte(SC520_PICICR, 0x40);
-
+ write_mmcr_byte(SC520_PICICR, 0x40);
+
/* set irq0-7 to edge */
write_mmcr_byte(SC520_MPICMODE, 0x00);
-
+
/* set irq9-12 to level, all the other (8, 13-15) are edge */
write_mmcr_byte(SC520_SL1PICMODE, 0x1e);
-
+
/* set irq16-24 (unused slave pic2) to level */
write_mmcr_byte(SC520_SL2PICMODE, 0xff);
-
- /* active low polarity on PIC interrupt pins,
+
+ /* active low polarity on PIC interrupt pins,
active high polarity on all other irq pins */
write_mmcr_word(SC520_INTPINPOL, 0);
/* set irq number mapping */
- write_mmcr_byte(SC520_GPTMR0MAP,0); /* disable GP timer 0 INT */
+ write_mmcr_byte(SC520_GPTMR0MAP,0); /* disable GP timer 0 INT */
write_mmcr_byte(SC520_GPTMR1MAP,0); /* disable GP timer 1 INT */
write_mmcr_byte(SC520_GPTMR2MAP,0); /* disable GP timer 2 INT */
- write_mmcr_byte(SC520_PIT0MAP,0x1); /* Set PIT timer 0 INT to IRQ0 */
+ write_mmcr_byte(SC520_PIT0MAP,0x1); /* Set PIT timer 0 INT to IRQ0 */
write_mmcr_byte(SC520_PIT1MAP,0); /* diable PIT timer 1 INT */
write_mmcr_byte(SC520_PIT2MAP,0); /* diable PIT timer 2 INT */
write_mmcr_byte(SC520_PCIINTAMAP,0x4); /* Set PCI INT A to IRQ9 */
write_mmcr_byte(SC520_PCIINTBMAP,0x5); /* Set PCI INT B to IRQ10 */
write_mmcr_byte(SC520_PCIINTCMAP,0x6); /* Set PCI INT C to IRQ11 */
write_mmcr_byte(SC520_PCIINTDMAP,0x7); /* Set PCI INT D to IRQ12 */
- write_mmcr_byte(SC520_DMABCINTMAP,0); /* disable DMA INT */
+ write_mmcr_byte(SC520_DMABCINTMAP,0); /* disable DMA INT */
write_mmcr_byte(SC520_SSIMAP,0); /* disable Synchronius serial INT */
write_mmcr_byte(SC520_WDTMAP,0); /* disable Watchdor INT */
write_mmcr_byte(SC520_RTCMAP,0x3); /* Set RTC int to 8 */
write_mmcr_byte(SC520_GP0IMAP,6); /* Set GPIRQ0 (ISA IRQ2) to IRQ9 */
write_mmcr_byte(SC520_GP1IMAP,2); /* Set GPIRQ1 (SIO IRQ1) to IRQ1 */
write_mmcr_byte(SC520_GP2IMAP,7); /* Set GPIRQ2 (ISA IRQ12) to IRQ12 */
-
+
if (CFG_USE_SIO_UART) {
write_mmcr_byte(SC520_UART1MAP,0); /* disable internal UART1 INT */
write_mmcr_byte(SC520_UART2MAP,0); /* disable internal UART2 INT */
- write_mmcr_byte(SC520_GP3IMAP,11); /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
+ write_mmcr_byte(SC520_GP3IMAP,11); /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
write_mmcr_byte(SC520_GP4IMAP,12); /* Set GPIRQ4 (ISA IRQ4) to IRQ4 */
} else {
write_mmcr_byte(SC520_UART1MAP,12); /* Set internal UART2 INT to IRQ4 */
write_mmcr_byte(SC520_UART2MAP,11); /* Set internal UART2 INT to IRQ3 */
- write_mmcr_byte(SC520_GP3IMAP,0); /* disable GPIRQ3 (ISA IRQ3) */
+ write_mmcr_byte(SC520_GP3IMAP,0); /* disable GPIRQ3 (ISA IRQ3) */
write_mmcr_byte(SC520_GP4IMAP,0); /* disable GPIRQ4 (ISA IRQ4) */
}
-
+
write_mmcr_byte(SC520_GP5IMAP,13); /* Set GPIRQ5 (ISA IRQ5) to IRQ5 */
write_mmcr_byte(SC520_GP6IMAP,21); /* Set GPIRQ6 (ISA IRQ6) to IRQ6 */
write_mmcr_byte(SC520_GP7IMAP,22); /* Set GPIRQ7 (ISA IRQ7) to IRQ7 */
write_mmcr_byte(SC520_GP8IMAP,3); /* Set GPIRQ8 (SIO IRQ8) to IRQ8 */
write_mmcr_byte(SC520_GP9IMAP,4); /* Set GPIRQ9 (ISA IRQ9) to IRQ9 */
- write_mmcr_byte(SC520_GP10IMAP,9); /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */
+ write_mmcr_byte(SC520_GP10IMAP,9); /* Set GPIRQ10 (ISA IRQ10) to IRQ10 */
write_mmcr_word(SC520_PCIHOSTMAP,0x11f); /* Map PCI hostbridge INT to NMI */
write_mmcr_word(SC520_ECCMAP,0x100); /* Map SDRAM ECC failure INT to NMI */
-
+
}
/* PCI stuff */
{
char pin;
int irq;
-
-
+
+
pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &pin);
irq = pin-1;
-
+
switch (PCI_DEV(dev)) {
case 20:
break;
case 17:
irq+=3;
break;
- default:
+ default:
return;
}
-
+
irq&=3; /* wrap around */
irq+=9; /* lowest IRQ is 9 */
-
+
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, irq);
-#if 0
- printf("fixup_irq: device %d pin %c irq %d\n",
+#if 0
+ printf("fixup_irq: device %d pin %c irq %d\n",
PCI_DEV(dev), 'A' + pin -1, irq);
#endif
}
-
+
static struct pci_controller sc520_cdp_hose = {
fixup_irq: pci_sc520_cdp_fixup_irq,
};
-void pci_init(void)
+void pci_init_board(void)
{
pci_sc520_init(&sc520_cdp_hose);
}
void setup_ali_sio(int uart_primary)
{
ali512x_init();
-
+
ali512x_set_fdc(ALI_ENABLED, 0x3f2, 6, 0);
ali512x_set_pp(ALI_ENABLED, 0x278, 7, 3);
ali512x_set_uart(ALI_ENABLED, ALI_UART1, uart_primary?0x3f8:0x3e8, 4);
ali512x_set_rtc(ALI_DISABLED, 0, 0);
ali512x_set_kbc(ALI_ENABLED, 1, 12);
ali512x_set_cio(ALI_ENABLED);
-
+
/* IrDa pins */
ali512x_cio_function(12, 1, 0, 0);
ali512x_cio_function(13, 1, 0, 0);
-
+
/* SSI chip select pins */
ali512x_cio_function(14, 0, 0, 0); /* SSI_CS */
- ali512x_cio_function(15, 0, 0, 0); /* SSI_MV */
+ ali512x_cio_function(15, 0, 0, 0); /* SSI_MV */
ali512x_cio_function(16, 0, 1, 0); /* SSI_SPI# (inverted) */
/* Board REV pins */
ali512x_cio_function(20, 0, 0, 1);
ali512x_cio_function(21, 0, 0, 1);
ali512x_cio_function(22, 0, 0, 1);
- ali512x_cio_function(23, 0, 0, 1);
+ ali512x_cio_function(23, 0, 0, 1);
}
{
/* set up the GP IO pins */
- write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); /* set the GPIO pin function 31-16 reg */
+ write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff); /* set the GPIO pin function 31-16 reg */
write_mmcr_word(SC520_PIOPFS15_0, 0xffff); /* set the GPIO pin function 15-0 reg */
- write_mmcr_byte(SC520_CSPFS, 0xf8); /* set the CS pin function reg */
+ write_mmcr_byte(SC520_CSPFS, 0xf8); /* set the CS pin function reg */
write_mmcr_byte(SC520_CLKSEL, 0x70);
-
- write_mmcr_byte(SC520_GPCSRT, 1); /* set the GP CS offset */
+
+ write_mmcr_byte(SC520_GPCSRT, 1); /* set the GP CS offset */
write_mmcr_byte(SC520_GPCSPW, 3); /* set the GP CS pulse width */
write_mmcr_byte(SC520_GPCSOFF, 1); /* set the GP CS offset */
write_mmcr_byte(SC520_GPRDW, 3); /* set the RD pulse width */
write_mmcr_byte(SC520_GPWRW, 3); /* set the GP WR pulse width */
write_mmcr_byte(SC520_GPWROFF, 1); /* set the GP WR offset */
- write_mmcr_word(SC520_BOOTCSCTL, 0x1823); /* set up timing of BOOTCS */
+ write_mmcr_word(SC520_BOOTCSCTL, 0x1823); /* set up timing of BOOTCS */
write_mmcr_word(SC520_ROMCS1CTL, 0x1823); /* set up timing of ROMCS1 */
- write_mmcr_word(SC520_ROMCS2CTL, 0x1823); /* set up timing of ROMCS2 */
-
+ write_mmcr_word(SC520_ROMCS2CTL, 0x1823); /* set up timing of ROMCS2 */
+
/* adjust the memory map:
* by default the first 256MB (0x00000000 - 0x0fffffff) is mapped to SDRAM
* and 256MB to 1G-128k (0x1000000 - 0x37ffffff) is mapped to PCI mmio
- * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */
-
-
+ * we need to map 1G-128k - 1G (0x38000000 - 0x3fffffff) to CS1 */
+
+
/* SRAM = GPCS3 128k @ d0000-effff*/
- write_mmcr_long(SC520_PAR2, 0x4e00400d);
-
+ write_mmcr_long(SC520_PAR2, 0x4e00400d);
+
/* IDE0 = GPCS6 1f0-1f7 */
- write_mmcr_long(SC520_PAR3, 0x380801f0);
+ write_mmcr_long(SC520_PAR3, 0x380801f0);
/* IDE1 = GPCS7 3f6 */
- write_mmcr_long(SC520_PAR4, 0x3c0003f6);
+ write_mmcr_long(SC520_PAR4, 0x3c0003f6);
/* bootcs */
- write_mmcr_long(SC520_PAR12, 0x8bffe800);
+ write_mmcr_long(SC520_PAR12, 0x8bffe800);
/* romcs2 */
- write_mmcr_long(SC520_PAR13, 0xcbfff000);
+ write_mmcr_long(SC520_PAR13, 0xcbfff000);
/* romcs1 */
- write_mmcr_long(SC520_PAR14, 0xabfff800);
+ write_mmcr_long(SC520_PAR14, 0xabfff800);
/* 680 LEDS */
- write_mmcr_long(SC520_PAR15, 0x30000640);
-
- asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
+ write_mmcr_long(SC520_PAR15, 0x30000640);
+
+ asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
if (CFG_USE_SIO_UART) {
- write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
+ write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
setup_ali_sio(1);
} else {
- write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
+ write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
setup_ali_sio(0);
silence_uart(0x3e8);
silence_uart(0x2e8);
int board_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
-
- init_sc520();
+
+ init_sc520();
bus_init();
irq_init();
-
+
/* max drive current on SDRAM */
write_mmcr_word(SC520_DSCTL, 0x0100);
-
+
/* enter debug mode after next reset (only if jumper is also set) */
write_mmcr_byte(SC520_RESCFG, 0x08);
-
+
/* configure the software timer to 33.333MHz */
write_mmcr_byte(SC520_SWTMRCFG, 0);
gd->bus_clk = 33333000;
-
+
return 0;
}
{
int minor;
int major;
-
+
major = minor = 0;
major |= ali512x_cio_in(23)?2:0;
major |= ali512x_cio_in(22)?1:0;
minor |= ali512x_cio_in(21)?2:0;
minor |= ali512x_cio_in(20)?1:0;
-
+
printf("AMD SC520 CDP revision %d.%d\n", major, minor);
-
+
return 0;
}
projects / platform / kernel / u-boot.git / blobdiff