#include "ppc440gx_i2c.h"
#include "sb_common.h"
+DECLARE_GLOBAL_DATA_PTR;
+
long int fixed_sdram (void);
/*************************************************************************
* metrobox_get_master
*
- * PRI_N - active low signal. If the GPIO pin is low we are the master
+ * PRI_N - active low signal. If the GPIO pin is low we are the master
*
************************************************************************/
int sbcommon_get_master(void)
{
ppc440_gpio_regs_t *gpio_regs;
- gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+ gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
if (gpio_regs->in & SBCOMMON_GPIO_PRI_N) {
return 0;
{
ppc440_gpio_regs_t *gpio_regs;
- gpio_regs = (ppc440_gpio_regs_t *)CFG_GPIO_BASE;
+ gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
if (gpio_regs->in & SBCOMMON_GPIO_SEC_PRES)
return 0;
unsigned short sernum;
/* Get the board serial number from eeprom */
- /* Initialize I2C */
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ /* Initialize I2C */
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
/* Read 256 bytes in EEPROM */
i2c_read (0x50, 0, 1, buff, 0x100);
/*************************************************************************
* sbcommon_fans
*
- * Spin up fans 2 & 3 to get some air moving. OS will take care
+ * Spin up fans 2 & 3 to get some air moving. OS will take care
* of the rest. This is mostly a precaution...
*
* Assumes i2c bus 1 is ready.
* Initialize sdram
*
************************************************************************/
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
long dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram (0);
+ dram_size = spd_sdram ();
#else
dram_size = fixed_sdram ();
#endif
*
*
************************************************************************/
-#if defined(CFG_DRAM_TEST)
+#if defined(CONFIG_SYS_DRAM_TEST)
int testdram (void)
{
- uint *pstart = (uint *) CFG_MEMTEST_START;
- uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
+ uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
uint *p;
printf("Testing SDRAM: ");
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
*
- * Assumes: 128 MB, non-ECC, non-registered
- * PLB @ 133 MHz
+ * Assumes: 128 MB, non-ECC, non-registered
+ * PLB @ 133 MHz
*
************************************************************************/
long int fixed_sdram (void)
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
- mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
- mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
+ mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
+ mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
+ mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
+ mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
+ mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
- mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
- /* RA=10 RD=3 */
+ mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
+ mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+ /* RA=10 RD=3 */
mtsdram (mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
- udelay (400); /* Delay 200 usecs (min) */
+ mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
+ mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
+ udelay (400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
- mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
+ mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
mfsdram (mem_mcsts, reg);
if (reg & 0x80000000)
break;
}
- return (128 * 1024 * 1024); /* 128 MB */
+ return (128 * 1024 * 1024); /* 128 MB */
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
* certain pre-initialization actions.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller * hose )
{
unsigned long strap;
return 1;
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
/*************************************************************************
* pci_target_init
* may not be sufficient for a given board.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller * hose )
{
- DECLARE_GLOBAL_DATA_PTR;
-
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+ out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
out32r( PCIX0_PIM0LAH, 0 );
out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+ out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*************************************************************************
if (0 == macaddr_idx) {
/* Initialize I2C */
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
/* Read 256 bytes in EEPROM */
i2c_read (0x50, 0, 1, buff, 0x100);
projects / platform / kernel / u-boot.git / blobdiff